Floor Joint Sealing contractors in Coombe Hill
Floor joint sealing in Coombe Hill, backed by over 20 years in commercial sealing. Fully insured and CHAS accredited.
- Failing joints at loading bays and dock doors
- Soft sealant dragged out of trafficked joints
- Open saw cuts full of debris
Floor joint sealing for businesses in Coombe Hill
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Floor joint sealing in Coombe Hill, done properly
Sometimes the concrete either side of a joint has already spalled. A filler laid against broken edges has nothing sound to grip, so if the edges need repair before any filling, we will say so and explain how it affects the programme. We work on construction joints, saw-cut induced joints and joints along racking aisles, and the failures we are asked to look at most are sealant pulled out along a truck route and cracked and crumbling joint fill. Whoever orders the work in Coombe Hill, the brief is usually the same: a clear scope, tidy work and joints that don’t fail again.
Areas such as a loading bay or car park deck in Coombe Hill typically have to stay in use. Joints are done in sections, with bays coned off one after another, so the site keeps operating, at times agreed with the building manager.
Our workmanship is guaranteed for 12 months, wherever the site is. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Where
- Coombe Hill (SW15, KT2)
- Region
- Greater London
- Cover
- 12 months on our workmanship
- Quotes
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Floor joint sealing in Coombe Hill: the local picture
Coombe Hill has at least three named business or industrial parks inside a 3-mile radius. Sites like these are full of saw-cut floor joints, yard slabs and car park joints. In London, decks, bays and service yards normally have to keep running, which is why we work a few bays at a time.
Campuses like Kingston University (Kingston Hill Campus) (to the south of Coombe Hill) mix old and new buildings, with movement joints wherever they meet. Another example is Rainbow Industrial Estate (2.2 miles south-east of Coombe Hill), where floors and yards would be done in stages around the occupiers.
Coombe Hill is about 2 miles north-east of Kingston upon Thames, in Greater London. Our applicators travel to Coombe Hill for work on floor joints. Across Greater London, 764 places are covered, including Coombe Hill. For work in that direction, see our London page (9 miles or so).
We take on floor joints across the SW15 and KT2 postcode area. Streets here include Keswick Avenue, Derwent Avenue and Robin Hood Lane. Being close to the A308, Coombe Hill is easy to get to with materials and equipment. Nearby places we also cover include Kingston Vale (1 mile east), Putney Vale (1 mile east), Coombe (1 mile south), Norbiton (2 miles south-west) and Motspur Park (2 miles south-east) for floor joints. Bigger towns within reach include London (9 miles north-east), City of Westminster (7 miles north-east), Marylebone (8 miles north-east), Kensington (5 miles north-east), St Pancras (9 miles north-east) and Shoreditch (10 miles north-east).
What’s near Coombe Hill
Locally, jobs take us to sites close to Coombe Girls' School, Canbury School and Richmond Park. The closest station to Coombe Hill is Norbiton station, about 1.6 miles south-west. Other landmarks nearby include Bentall Centre (2.2 miles south-west) and Kingston Hospital (1.4 miles south-west). Not far away are Kingston Hill Road area and Fishpond Wood and Beverley Meads.
Work for main contractors and building owners
Blocks and communal areas make up much of the work for housing associations and agents. We phase the work so people keep access, with each stage agreed with your site contact.
Hospitality, education, healthcare, office and retail clients come to us directly as well. The work is planned around how the building runs, so the building keeps working while we do.
Our process
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Any old material is cut back to clean, sound faces, the manufacturer’s primer is applied where it’s called for, and the sealant is tooled off neatly. Planning a London job such as one in Coombe Hill starts with access. Give us the hours we can be on site and we will schedule to suit.
- We agree the traffic routes and phasing with your site team.
- Any joints with broken edges are flagged before work starts.
- We clear each run back to clean concrete.
- The chosen filler or sealant goes in flush with the slab.
- You get a time for each zone to reopen.
What we need from you
- Agree which areas must stay open
- Tell us your opening times and when work is allowed
- Have the specification and drawings to hand
Get a fixed quote
A handful of photos and a postcode is the fastest way to a quote. Send them through the quote form, or call the office on 01277 525 020 or email the details over to discuss it first.
Related advice
Also near Coombe Hill
More services for Coombe Hill
Should maintenance staff do it?
Site maintenance staff can often handle a short internal joint. The usual problems come from preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
Certain joints really need a specialist: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. A poor seal in places like these tends to cost more to put right later.
When it isn’t the sealant
Sealant solves a lot, but not everything, and we are upfront when that’s the case. It won’t fix:
- Wide or random cracking that suggests a structural issue
- Spalled arrises, which need an edge repair first
- A floor that rocks at the joints, which needs a structural fix
Not sure which it is? You can ring 01277 525 020 or use the quote form and we will tell you honestly before you book.
Surfaces we seal
- Joints along racking aisles
- Construction joints
- Retail and showroom floors
- Forklift and pallet-truck routes
- Saw-cut induced joints
- Loading bays
Questions about Coombe Hill
Can you work at a site such as St. George's Industrial Estate, by Coombe Hill?
Yes. Estates, retail parks and business parks around Coombe Hill, St. George's Industrial Estate among them, are all within reach. A few photographs and the unit address let us price the work.
Do you work in London buildings with loading restrictions?
Yes, most London buildings have access rules of some kind, and we plan around them. Say when the building is occupied and when it’s quiet, and we will plan accordingly. We allow for the ULEZ, which covers every borough
Is the floor joint work guaranteed?
Every job has our 12-month guarantee. It covers our workmanship, not later slab movement or damage from impacts.
How soon can traffic go back on the floor?
Each product has its own cure time and cooler floors take longer. Phasing is planned with that in mind.
Can you work to our specification?
Yes. Include it with the drawings when you ask for a quote, and we’ll price the work to it.
Do you use semi-rigid filler or flexible sealant on floor joints?
There isn’t one answer for a whole floor. Hard wheels need edge support, which points to a semi-rigid filler and perimeter or movement joints need flexibility. The quote sets out what goes where.
Who decides which product is used?
A specification, where there is one, decides it. Without one, the joint decides: its movement, its surfaces and what it has to cope with.
What happens if it’s left?
Open joints are where dirt collects, out of reach of the floor cleaner. Where the floor is on show or needs to be kept clean, that is a problem. Flush, filled joints leave nothing for cleaners to dig out. In a London building, a failed joint rarely affects only one party: water travels through shared structures, and a small leak becomes a dispute between occupiers. Dealing with it early is simpler for everyone.
There’s no price list, since every building and every scope is different. For a fixed figure, call for a quote.
What you get with us
- Commercial sealant work since 2005
- Health and safety: CHAS accredited
- Work to your specification and the manufacturer’s guidance
- Old sealant cut out, never sealed over
Read what affects the cost or our accreditations.
Do you need floor joint sealing in Coombe Hill?
Oil, laitance, dust and old cleaning chemicals build up inside joints. If the faces aren’t taken back to clean concrete first, the new material simply lifts out.
Most enquiries start with something like this:
- Trucks and loads jolting over damaged joints
- Old filler gone hard, cracked or loose
- Failing joints at loading bays and dock doors
- Filler that has parted from one face
Hospitals like New Victoria Hospital (to the south-east of Coombe Hill) have multi-storey or surface car parks whose joints carry vehicles round the clock.
Comparing quotes
- Proof of insurance
- The named product and why it was chosen
- Their pre-qualification and accreditations
- How joint depth will be controlled