Fire Stopping in Wildhern
Looking for fire stopping in Wildhern? It’s simple: send details, get a quote, we seal, guaranteed.
- Seals disturbed by maintenance and left open
- Fire-stopping items raised at inspection or handover
- Non-fire-rated filler around services
Fire stopping across Wildhern
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Fire stopping for commercial buildings in Wildhern
It helps to set out our role at the start. Deciding the specification sits with the designer, the fire engineer and building control. What we bring is careful installation of the specified sealant, to the maker’s guidance. We work on small duct penetrations where the tested detail allows, joints between fire-resisting walls and floors and cable penetrations, and the failures we’re asked to look at most are seals that don’t match their tested detail and openings found when ceilings come down for a refit. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Wildhern it comes down to the same thing: failed joints cut out, faces prepared and the right sealant laid to the right depth.
For a smaller site near Wildhern, we plan to do all the penetrations in one go, with the specification and photos sent in advance. Design and sign-off belong to the designer or building control; we install what’s specified.
Work we carry out in Hampshire comes with a 12-month guarantee. If an installation problem shows up, give us a call on 01277 525 020 or email drawings and photos and we’ll arrange a return visit.
- Location
- Wildhern (SP11)
- Region
- Hampshire
- Guarantee
- 12 months on every job
- Quote
- Quoted before any work starts
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Service penetrations in Wildhern buildings
In England, Approved Document B covers fire stopping of openings and penetrations. Its BS 476 references are being withdrawn from 2 September 2029, with BS EN 13501-2 classification taking over, subject to transitional arrangements. Our part stays the same: the specified product, installed to its tested detail. At about 63 miles from central London, Wildhern is within reach of the capital. Office refits around the commuter belt bring new cabling through fire-resisting walls.
At a healthcare site like Andover War Memorial Hospital, which lies south of Wildhern, new services through compartment walls are a constant, and each needs the specified seal. Industrial units on estates such as Glenmore Trade Park, 2.7 miles south of Wildhern, often separate offices from warehouse space with fire-resisting walls, and new services through them need the specified seal.
Wildhern is about 3 miles north of Andover, in Hampshire. Wildhern sits inside our coverage, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. We work across 723 places in Hampshire. There’s a separate page for Southampton, roughly 24 miles from Wildhern.
Business premises anywhere in SP11 are within our area. Sites close to Wildhern are covered too, including Upper Enham (1 mile south-east), Enham Alamein (1 mile south-east), Little London (2 miles east), Knights Enham (2 miles south-east) and Smannell (2 miles south-east). Further afield, our area takes in Andover (3 miles south), Hyde (15 miles south-east), Tidworth (7 miles west), Weeke (15 miles south-east), Kempshott (15 miles east) and Ludgershall (5 miles west).
Local landmarks in Wildhern
In Wildhern, that means premises near The Hare & Hounds pub and the streets around them. For rail, the closest station is Andover station, roughly 3.1 miles south of the centre. Well-known places in the area include Finkley Down Farm Museum (3.1 miles south-east) and Andover War Memorial Hospital (2.8 miles south). Green spaces nearby include Anton Lakes and Mill Lake.
Questions we are asked in Wildhern
Does your area include sites such as Glenmore Trade Park, near Wildhern?
Yes. We cover Wildhern and the area around it, including industrial estates, business parks and retail parks such as Glenmore Trade Park. Photos and a short description are enough for a first look.
Is Wildhern too small for you to travel to?
No. Small places get the same service as large ones. We work across Greater London and the South East. We plan jobs in smaller places so return trips are kept to a minimum.
How long before the joints can be used?
The product and site conditions decide that. Some products skin over quickly but need longer to cure fully, so we’ll confirm the curing time on the day.
Can you handle several sites?
Yes. Several buildings can share a single quote, with one point of contact across South East England, Greater London and Scotland.
Does weather matter for sealant work?
It can, for external work. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so we watch the forecast and rearrange outside work if we have to. Internal work is far less affected.
Do you approve fire stopping for building control?
No. Sign-off isn’t ours to give, and we don’t hold a third-party installer certificate. We work to the specification and the manufacturer’s installation guidance.
Which standards are fire seals tested to?
Penetration seals are tested to BS EN 1366-3 and linear joint seals to BS EN 1366-4. Classification follows BS EN 13501-2 as E for integrity and I for insulation, with a time such as EI 60 or EI 120. The rating applies to the product as tested.
When it isn’t the sealant
Sealant solves a lot, but not everything, and we’d rather tell you before you spend money. These need a different solution:
- Large openings beyond what any sealant detail covers
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Gaps in walls that were never built as compartment walls
If you’re not sure, just call the office on 01277 525 020 or email the details over and we will give you a straight answer.
Joints and surfaces we work on
- Pipe penetrations
- Service gaps in risers
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
- Small duct penetrations where the tested detail allows
- Cable penetrations
Places near Wildhern
Also in Wildhern
For managing agents and facilities managers
We take on planned maintenance as well as one-off repairs: working through a building or an estate in stages that fit your budget. Wildhern can form part of a wider programme across Hampshire.
For main contractors, we work as the sealant subcontractor on new-build and refurbishment projects. We work to your programme, your specification and your site rules.
What we’re called out for in Wildhern
Head-of-wall joints and wall-to-wall junctions are frequent weak points. Deflection and building movement can open these gaps, and the wrong product can split as a result. The tested detail for a linear joint states the width and movement it covers.
Typical triggers for a call:
- Service penetrations left open after M&E works
- Builders’ foam or ordinary silicone in compartment walls
- Fire-rated sealant that has cracked or shrunk back
- Fire seals cut back for extra cables and never reinstated
Holiday works at schools like Hatherden Church of England Primary School often leave service openings to seal before pupils return.
Comparing quotes
- Whether their applicators hold CSCS cards
- Will failed sealant be removed rather than covered?
- Health and safety accreditation such as CHAS
- Which product they’ll use, and why it suits the joint
Should maintenance staff do it?
Some joints are best left to specialists: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. A poor seal in places like these tends to cost more to put right later.
What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
Cost factors for service penetrations
These are the things that shape the price:
- Travel to remote or island sites
- How much existing material needs removing
- Whether the work must be split into stages
- Access and working height
The product called for affects the cost, and so does the preparation, from cutting out to priming and backing rod. Access, phasing and site requirements come into it too.
Sending details for a quote
Good information means a firmer quote. When you get in touch, include:
- The type of building and who uses it
- Access details, including height
- Whether an asbestos survey exists
- The site address and postcode
We quote a fixed sum against the scope you give us, so you know the figure before anyone is on site. To start the process, phone 01277 525 020 or email a schedule or drawings.
Our process
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. On site, the work typically takes a single visit for a short list of penetrations, or a phased programme for a whole building, and we clear our waste as we work. Rural sites near Wildhern may need directions, gate codes or a contact on site. Add it to your enquiry and we will build it into the plan.
- First we confirm the product and tested details named in the specification.
- We sort the openings by the detail each one needs.
- Old or wrong materials are cut out.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Preparing the site
- Let us know about inductions and permits
- Move anything stored against the joints
- Share your working hours and any access restrictions
Getting a fixed quote
A good quote starts with a clear picture: the joints involved, quantities, access and the product called for. Send what you have, and we will arrange a site visit if anything is unclear.