Tonbridge fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps across Tonbridge, by CSCS-carded applicators. CHAS accredited and fully insured.
- Damaged fire seals in risers and voids
- Openings found when ceilings come down for a refit
- Seals that don’t match their tested detail
Need fire stopping in Tonbridge?
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Common questions from Tonbridge clients
Can you take on a job at a hospital such as Tonbridge Cottage Hospital?
Yes, hospitals are one of the sectors we cover. Each area is agreed with the ward or department and the estates team in advance.
Does your area include sites such as Kingstanding Business Park, near Tonbridge?
Yes. We cover Tonbridge and the area around it, including industrial estates, business parks and retail parks such as Kingstanding Business Park. Send details of the unit and the work through our quote form for a quick quote.
What’s the quickest route to a quote?
It works in four steps: send details, receive a fixed quote, we carry out the work, and it’s guaranteed. Step one needs little more than photos and a postcode.
How long does a job like this take?
The duration is planned around your programme and the access we’re given. You will have an expected duration with the quote.
Do you hold third-party fire-stopping installer certification?
No, and we won’t imply otherwise. Third-party schemes aren’t a legal requirement, but many clients and main contractors ask for them, so it’s worth checking what your contract says. Where it isn’t required, we install the specified sealant to the maker’s details.
Are you fully insured?
Yes. We’re fully insured, and the certificate can go with your quote.
What about RAMS and site documents?
Let us know which documents the site needs, such as RAMS, an insurance certificate or CSCS details, and we’ll confirm them with the quote.
Fire stopping in Tonbridge, done properly
We should be clear about what we do and don’t do. Deciding the specification sits with the designer, the fire engineer and building control. We fit the specified fire-rated sealant following that specification and the maker’s installation guidance in Tonbridge and nearby. We work on cable penetrations, linear gaps at wall heads and joints between fire-resisting walls and floors, and the usual reasons a site gets in touch are fire stopping installed outside its tested range and expanding foam used as fire stopping. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Tonbridge it comes down to the same thing: failed joints cut out, faces prepared and the right sealant laid to the right depth.
In a town like Tonbridge, penetration seals normally need attention after other trades have been through. A check after services work is sensible; tell us what the specification says and we will install to it.
Work we carry out comes with a 12-month guarantee. Should something we installed fail, call 01277 525 020 or send details through our quote form and we will come back to it.
- Where
- Tonbridge (TN9, TN10, TN11)
- Wider area
- Kent
- Cover
- 12 months on every job
- Quotes
- Quoted before any work starts
- Call
- 01277 525 020
- Page updated
- 3 November 2026
After the work
Keep the joints in good shape with a few simple steps:
- Make fire stopping part of every scope that crosses a fire-resisting wall
- Look above ceilings when tiles are lifted for other jobs
- Get seals inspected before ceilings and boxing close
- Keep product data and details in the fire safety file
After every round of M&E works, check that the openings created have been sealed. A short check at the end of each job saves a long hunt later.
Looking at service areas on a regular cycle pays off. Catching a damaged seal early keeps the fix small.
Our process
On arrival, we sign in, go through any site induction and check how permits are handled. Everything around the joints gets protected before anything is cut or cleaned, and the work normally takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence. In a town such as Tonbridge, most jobs are single buildings. We start with your photos, drawings or a site visit, then send a fixed quote.
- We read the specification, drawings or penetration schedule you send and raise any questions before we price.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- We fit the backing the detail asks for, to the stated depth.
- We apply the specified sealant to the depth and around the services as the detail shows.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
What we need from you
- Explain the parking and delivery arrangements
- For older buildings, check the asbestos register before work
- Tell us your opening times and when work is allowed
Getting a fixed quote
Send us photos, drawings or a joint schedule are often enough for a fixed quote. If the job needs a look first, we will arrange a site visit.
Advice
Should maintenance staff do it?
The visible bead is only part of the job. Backing rod, primer where specified and a joint designed to move with the building are where general trades tend to cut corners.
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
When something else is needed
We seal joints; we don’t mend everything behind them. On its own, sealant can’t deal with:
- Issuing fire ratings or certificates for seals
- Construction that lacks the fire resistance the seal relies on
- Openings that need collars, wraps, batts or boards rather than sealant
Not sure which it is? You can call the office on 01277 525 020 or send photos by email and we’ll tell you honestly before you book.
Where we work in Tonbridge
- Linear gaps at wall heads
- Service gaps in risers
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Pipe penetrations
Quoting for work in Tonbridge
Each job is priced on its own details. The things that drive the figure:
- Joint width, depth and condition
- The product specified
- Whether the work must be split into stages
- Whether old sealant has to be cut out first
Access can matter as much as the joints themselves: easy-to-reach joints are quicker than those that need equipment to get to. Mention the access as part of your enquiry.
Before you send an enquiry
Diagnosis starts before we arrive. Let us know:
- Drawings or a marked-up plan, if available
- Any dates the work must fit around
- Anything awkward about access or site hours
- Photos of the joints, close up and from further back
Specifications, drawings and tender packages are welcome with any enquiry, and we will price the work to it. For smaller jobs, photographs and a description will do.
Fire-rated sealing for Tonbridge buildings
Fire stopping of openings and penetrations in England falls under Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. What we install is set by the specification, and it goes in to the tested detail. The area within 2 miles of Tonbridge holds a number of hotels. In hotels, bedroom and corridor walls are normally fire-resisting, so services added in a refit need sealing with the specified product.
Offices at parks like Kingstanding Business Park (to the south of Tonbridge) are re-cabled with each new tenant, and compartment walls need sealing afterwards to the tested detail. Workshops and IT rooms at colleges like West Kent College (1.1 miles south-west of Tonbridge) are re-serviced often, leaving penetrations to seal.
Tonbridge is about 12 miles south-west of Maidstone, in Kent. If you’re looking for fire stopping in Tonbridge, we can help, as we do across Kent. 931 places across Kent fall within our area, Tonbridge among them. London is covered too, some 26 miles away.
We cover the TN9, TN10 and TN11 postcode districts for service penetrations. Streets here include High Street, Old London Road and London Road, and sites on any of them can send details for a fixed quote. With the A26 and A227 nearby, Tonbridge is straightforward for us to reach. We also cover Lower Haysden (2 miles south-west), Leigh (3 miles west), Bidborough (3 miles south-west), Southborough (3 miles south) and Printstile (3 miles south-west). Nearby towns on our patch include Maidstone (12 miles north-east), Sevenoaks (7 miles north-west), Royal Tunbridge Wells (4 miles south), Swanley (14 miles north), Kings Hill (7 miles north-east) and Foley Park (12 miles north-east).
Around Tonbridge
In Tonbridge, that means premises near Haysden Country Park, Royal Rise Primary School and Hillview School for Girls and the streets around them. For rail, the closest station is Tonbridge station, about 0.6 miles south-west. A little further out are The Milne Museum (less than half a mile west) and Tonbridge Castle (less than half a mile south-west). Not far away are Tudeley Woods RSPB reserve and Barden Lake.
When to call us in Tonbridge
Damage plays a part too. Maintenance work can knock a seal, cut it back for an extra cable or remove it with an old pipe and the opening isn’t always resealed.
Most enquiries start with something like this:
- Hidden openings found during inspections
- Openings left by services added after handover
- Fire stopping installed outside its tested range
- Fire-stopping items raised at inspection or handover
Residences at universities like University of Kent - Tonbridge (0.5 miles south-west of Tonbridge) have compartment walls that must be resealed whenever services change.
What to look for in a quote
- Who will actually carry out the work
- The terms of the workmanship guarantee
- Is depth set with backing rod, or bond-breaker tape in shallow joints?
- Which product they’ll use, and why it suits the joint