Tile Hurst fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Tile Hurst and nearby, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Fire-rated sealant that has cracked or shrunk back
- Service penetrations left open after M&E works
- Openings found when ceilings come down for a refit
Fire stopping for businesses in Tile Hurst
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Fire stopping in Tile Hurst: the local picture
Tile Hurst has several hotels close by, all within 2 miles. Hotels are divided into compartments, and refurbishments that add pipes and cables through bedroom and corridor walls leave gaps to close. For England, the fire stopping of penetrations is dealt with in Approved Document B. From 2 September 2029, BS 476 references are being taken out of Approved Document B, leaving BS EN 13501-2 classification as the route, subject to the Government’s transitional arrangements. We install whatever has been specified, to the product’s tested detail.
Older community buildings such as Zoar Strict Baptist Chapel that have been rewired or given new heating can have service gaps through walls worth checking against the specification. Shop fits on retail sites such as Hailsham Retail Park (to the south-east of Tile Hurst) can bring new services through fire-resisting walls between units, to be sealed with the specified product. Hotels like Boship Farm Hotel, 0.6 miles north-west of Tile Hurst, are refurbished in phases, and each phase can open up compartment walls.
Tile Hurst is about 1 mile north-west of Hailsham, in East Sussex. We cover commercial sites throughout Tile Hurst, whether it’s a single job or part of a planned programme. 308 places across East Sussex fall within our area, including Tile Hurst. Brighton is covered too, around 16 miles from Tile Hurst.
Anyone looking for fire stopping in BN27 gets the same process as the rest of our area: send details, get a quote, we seal, guaranteed. If your building is just outside Tile Hurst, we cover Lower Horsebridge (1 mile north), Hailsham (1 mile south-east), Upper Horsebridge (1 mile north-east), Lower Dicker (1 mile north-west) and Hellingly (1 mile north-east). Nearby towns on our patch include Eastbourne (6 miles south), Hastings (14 miles east), Bexhill-on-Sea (10 miles east), Seaford (9 miles south-west), Lewes (10 miles west) and Crowborough (13 miles north).
Local landmarks in Tile Hurst
Around Tile Hurst, our work takes us to commercial buildings near Hailsham Community College, The Grenadier pub and Bede's Prep School. The nearest railway station is Polegate station, about 3.4 miles south. Other landmarks nearby include Herstmonceux Castle (4.5 miles east) and Hellingly Hospital Railway (1.6 miles north-east). Green spaces nearby include Combe Hill.
Fire stopping in Tile Hurst
No fire sealant works on its own: its test evidence covers one product in one kind of wall or floor, with set services, gaps, depths and backing. Before we seal anything, we check the opening against the detail it is meant to follow, and raise it with you if it falls outside. If you are dealing with hidden openings found during inspections and openings left by services added after handover, we can put it right, whatever the surface. A single leaking joint is often how a building in Tile Hurst first comes to us: we check the joints around it and give you an honest view of what needs doing now and what can wait.
Rural conversions around Tile Hurst can put new fire-resisting partitions inside older structures. Where a pipe or cable passes through a fire-resisting wall, the seal must match the tested detail: product, substrate, gap and depth.
Our 12-month guarantee is about workmanship, not wear and tear. Sealant wears with time, and movement, weather, cleaning and use decide how fast, so we spell out the cover before we begin.
- Where
- Tile Hurst (BN27)
- Region
- East Sussex
- Cover
- A 12-month guarantee
- Quote
- Quoted before any work starts
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Questions we’re asked in Tile Hurst
Can you seal around new services in a hotel near Tile Hurst?
Yes, where fire-rated sealant is the specified product. It goes in to the manufacturer’s tested detail for the wall or floor and the services passing through, and we’ll tell you if the detail calls for a collar, wrap or batt instead.
Is Tile Hurst off your patch?
Not at all. Tile Hurst is within our area. London and every South East county are within our area. We plan jobs in smaller places so return trips are kept to a minimum.
Do you have public liability insurance?
Yes. We’re fully insured, and the certificate can go with your quote.
Can the building stay open while you work?
In most cases, yes. Phased work can be planned so areas stay in use.
What will the job cost?
Every job gets its own fixed quote. For yours, give us a call on 01277 525 020 or email the details over.
Do you take on small jobs?
Small jobs are welcome alongside larger packages. Send details for a fixed quote.
Which sealant will you use?
Where there’s a specification, we use the product it names. Otherwise, we recommend a product to suit the joint’s movement, the substrate and the conditions, following the manufacturer’s guidance.
Why act early in Tile Hurst
An improvised seal can look finished while offering no tested performance. Correcting it means cutting it out and starting again with the specified product, so it makes sense to get it right first time. One visit to deal with every failing joint makes more sense than several trips to a place like Tile Hurst, rather than one at a time. Photos of every joint help us quote for the whole job.
Every site prices differently: joint size, product, access and site hours all play a part. A fixed quote follows once we understand the job.
Why us?
- Constructionline member
- Commercial sealant work since 2005
- 12-month guarantee on workmanship
- A fixed quote before work starts
Take a look at what affects the cost and our accreditations.
Owners, agents and contractors
Building owners and managing agents use us on sealant work across single buildings or whole portfolios around Tile Hurst. Several sites can go on one quote, which keeps the paperwork simple.
Hospitality, education, healthcare, office and retail clients come to us directly as well. The work is planned around how the building runs, so the building keeps working while we do.
Doing it in-house
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
For most general trades, sealant is a sideline. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint.
Places near Tile Hurst
What else we do in Tile Hurst
On site: what to expect
At the end of each section, the masking comes off, the area is cleaned and every joint is checked with your site contact. If an area should be left alone while the sealant cures, we say how long and put signs out. Jobs in and around smaller places like Tile Hurst are typically planned as a single visit, so we ask for photographs and rough sizes first. That way the right products come on the day.
- We ask for the product and detail your designer has specified.
- We sort the openings by the detail each one needs.
- Old or wrong materials are cut out.
- Mineral wool or other backing is fitted where required.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Preparing the site
- Confirm the product named in the specification
- Point out any areas we must not close
- Share your working hours and any access restrictions
Quotes
Quotes are fixed against the scope you send, so you know the figure before anyone is on site. To start the process, give us a call on 01277 525 020 or email a schedule or drawings.
Read more
What the job involves on each surface
Plastic pipes
Waste and drainage pipes through floors are a frequent case. Whether sealant alone is acceptable depends entirely on the tested detail, and we won’t substitute it for a specified collar.
Masonry and concrete
Openings through concrete vary from tidy cores to rough break-outs. Each gap is measured where it is widest so we know it sits within the tested range, and any outside it are raised with you.
Maintenance after handover
For the best life from the joints:
- Check with the data sheet before painting over fire sealant
- Check risers and ceiling voids after each round of works
- Flag new cables with no seal around them
- Don’t let anyone top up a fire seal with the wrong product
Keep the product data and installation details with the building’s fire safety information. It makes later repairs much easier to match.
Regular walk-rounds of service areas are worth the time. Catching a damaged seal early keeps the fix small.