Strathyre fire stopping
Need fire stopping in Strathyre? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Open linear gaps along the top of fire-resisting walls
- Penetration schedules that need working through
- Builders’ foam or ordinary silicone in compartment walls
Fire stopping near Strathyre
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
How we handle fire stopping in Strathyre
Opened ceilings and riser doors often reveal service openings nobody sealed. If a specification already covers those walls and floors, we can reseal to it, matching the product and detail it names. With no specification in place, the first step sits with your designer or fire engineer, not with us. We work on service gaps in risers, joints between fire-resisting walls and floors and small duct penetrations where the tested detail allows, and the usual reasons a site gets in touch are seals that don’t match their tested detail and fire sealant pulled out of the opening. Most enquiries from Strathyre start with one failed joint and grow into a wider look at the building: we check the joints around it and give you an honest view of what needs doing now and what can wait.
In smaller Scottish places like Strathyre, buildings with fire-resisting walls typically include schools, care homes, hotels and health centres. Where services pass through, specified fire-rated sealant is installed following the manufacturer’s guidance for that wall or floor.
The 12-month guarantee covers our workmanship: preparation, application and finish. It doesn’t extend to damage, other trades’ later work or movement the joint was never designed to take.
- Location
- Strathyre (FK18)
- Region
- Stirling
- Guarantee
- 12 months on our workmanship
- Quotes
- Quoted before any work starts
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Signs you need fire stopping in Strathyre
On a busy project, programme pressure can mean fire stopping is rushed or left to whichever trade is closest. That is how unsuitable products and improvised details end up in compartment walls and later need putting right.
These are often picked up first by site or facilities staff:
- Seals that don’t match their tested detail
- Service penetrations left open after M&E works
- Unsealed penetrations discovered above suspended ceilings
- Damaged fire seals in risers and voids
Buildings near Strathyre get the fire-rated product that’s specified, installed to its tested detail.
Before you book anyone
- Are they CHAS accredited or on Constructionline?
- How joint depth will be controlled
- Whether their applicators hold CSCS cards
- Whether old or failed sealant will be cut out, not overlaid
What we can’t put right
Not every problem is a sealant problem, and we’d rather tell you before you spend money. It won’t fix:
- Fire doors, dampers or other fire safety equipment
- Deciding what a wall or floor needs, which belongs to the designer
- Gaps in walls that were never built as compartment walls
If you’re not sure, just call 01277 525 020 or use the quote form and we’ll give you a straight answer.
What we seal
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
- Service gaps in risers
- Pipe penetrations
From enquiry to sign-off
On arrival, we report to your site contact and complete whatever induction the building runs. Floors, finishes and fittings next to the joints are covered before any cutting starts, with the work itself usually taking anything from one day to a planned run of visits, depending on the number of seals and the access. Jobs near Strathyre are often grouped with others in the same area. Tell us how flexible your dates are.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned so the seal starts clean.
- Backing and fire-rated sealant are installed to the detail and tooled.
- Anything outside the detail is reported to you rather than sealed.
Preparing the site
- Share the asbestos register for older buildings
- Let us know about inductions and permits
- Agree which areas must stay open
Ask for a quote
Tell us about the building, the joints and when you need the work done, and we’ll put a fixed quote together. The easiest way is to give us a call on 01277 525 020 or email us.
Related advice
Quoting for work in Strathyre
The price varies from site to site. Expect it to depend on:
- Site requirements such as inductions and permits
- Access and working height
- Working within restricted access windows
- How much existing material needs removing
The price depends on the quantity of joints, how much old material needs removing and the access. Call for a fixed quote when you are ready.
Sending details for a quote
A few photographs plus some basic facts will normally do. It helps to include:
- Anything awkward about access or site hours
- Approximate linear metres or a joint schedule
- The asbestos register, for older buildings
- A wide shot and a close-up of the area
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To start the process, call the office on 01277 525 020 or use the quote form.
When to bring in a specialist
Redoing a failed joint normally costs more than getting it right at the outset, since all of it has to come out and the faces be cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
Certain joints really need a specialist: for example fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. A poor seal in places like these tends to cost more to put right later.
Service penetrations in Strathyre buildings
In Scotland, clause 2.1.14 of the non-domestic Technical Handbook expects service penetrations to keep at least the fire resistance duration of the wall or floor, and products should be tested for their end use. Where fire-rated sealant is specified, that’s what we install, to the tested detail.
Hotels such as Ben Sheann Hotel, less than half a mile north-east of Strathyre, rely on fire-resisting walls between bedrooms and corridors, and refits that add services leave penetrations to seal where fire-rated sealant is specified.
Strathyre is about 21 miles north-west of Stirling, in Stirling. We cover commercial sites throughout Strathyre, whether it’s a single job or part of a planned programme. Strathyre is one of 52 places we cover in Stirling. Sites around Glasgow have their own page, about 32 miles away.
Work on service penetrations is covered throughout FK18. Close to Strathyre, our area also takes in Lochearnhead (5 miles north-east), Kilmahog (6 miles south-east), Brig o'Turk (6 miles south), Callander (7 miles south-east) and St Fillans (10 miles north-east).
What’s near Strathyre
A little further out are Edinample Castle (4.3 miles north-east). Not far away are Loch Lubnaig.
Places near Strathyre
What else we do in Strathyre
Looking after the joints
For the best life from the joints:
- Foam or ordinary sealant is never a fire-seal repair
- File the specified details where the next contractor can find them
- Check risers and ceiling voids after each round of works
- Leave fire sealant to cure fully before covering it
During planned inspections, look at seals in risers, cupboards and voids. Watch for cracked sealant, new services with no seal and openings that have grown.
Specify fire stopping early on refits, not as an afterthought. The designer can then choose details that suit the services planned.
FAQs: Strathyre
Do you decide the fire-stopping details for buildings in Strathyre?
No. Fire-stopping design and sign-off belong to the designer, principal designer, fire engineer or building control. We install what’s specified, to the product’s tested detail.
Is a smaller place like Strathyre outside your area?
No. Small places get the same service as large ones. We work across every Scottish council area. We plan jobs in smaller places so return trips are kept to a minimum.
Is colour matching possible?
That depends on the product specified. Some ranges offer many colours, others very few, so we will confirm the colours available for the specified product with the quote.
Will you come and look before quoting?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we will arrange a visit.
Does weather matter for sealant work?
It can, for external work. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so external work may be moved if conditions aren’t right. Indoors, the weather is rarely a problem.
Will your applicators have CSCS cards?
Yes. We use CSCS-carded applicators, as many construction sites ask for.
Is it fine to apply new sealant on top of old?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, since fresh sealant will not bond reliably to aged material.