Fire Stopping in Stanhope
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Stanhope and nearby, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Fire stopping installed outside its tested range
- Fire-rated sealant that has cracked or shrunk back
- Damaged fire seals in risers and voids
Fire stopping for Stanhope sites
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How we handle fire stopping in Stanhope
A fire-rated sealant is only one part of a tested system: the evidence covers a specific product, wall or floor type, service, gap, depth and backing. We match each opening to that detail before any sealant goes in. The enquiries we see most involve fire stopping installed outside its tested range and openings found when ceilings come down for a refit, on service gaps in risers, pipe penetrations and linear gaps at wall heads. A specialist sealant contractor works differently from a general builder: in Stanhope, that means joint design, primers and backing rod as standard.
Around Stanhope, penetration and linear seals tend to be one-building jobs. Send the specification, drawings or photographs of the openings and we will quote to suit.
Whoever the client is, the cover is the same: twelve months on the work we carried out. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Place
- Stanhope (TN23)
- Wider area
- Kent
- Cover
- 12 months on our workmanship
- Quote
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Common problems we fix in Stanhope
Some seals fail because the wrong product went in: builders’ foam or ordinary silicone used to fill a hole. The opening looks sealed but has no fire test evidence behind it, so it has to come out.
If one of these sounds familiar, it’s time for a closer look:
- Seals that don’t match their tested detail
- Openings left by services added after handover
- Openings found when ceilings come down for a refit
- Unsealed joints where partitions meet the slab
Workshops and IT rooms at colleges like Ashford College (to the north-east of Stanhope) are re-serviced often, leaving penetrations to seal.
What your quote should include
- Will failed sealant be removed rather than covered?
- What site paperwork they can supply
- Whether their applicators hold CSCS cards
- Is depth set with backing rod, or bond-breaker tape in shallow joints?
Nearby places to Stanhope
More services for Stanhope
Stanhope: questions and answers
Can work at a site such as Ashford College fit around teaching?
Yes. Education sites normally want the work in vacations or in phases during term, and we plan to suit. Any paperwork you need, from RAMS to our insurance certificate and CSCS details, is confirmed with the quote.
How does the removal of BS 476 from Approved Document B affect fire-rated sealing in Stanhope?
References to BS 476 classes are being removed from Approved Document B from 2 September 2029, after which BS EN 13501-2 classification is the route, subject to transitional arrangements. The designer or fire engineer sets the specification, and we install the product to the manufacturer’s tested detail.
Are your applicators CSCS-carded?
Yes. We use CSCS-carded applicators, as many construction sites ask for.
How many days will you need on site?
We plan the time on site around your programme and access. We will give you an estimate of time on site when we quote.
What will the job cost?
There isn’t a price list, as every site differs. Send photographs or drawings and we will price it at a fixed figure.
Will you quote for a small job?
Small jobs are welcome alongside larger packages. Send details for a fixed quote.
Is colour matching possible?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We will confirm the colours available for the specified product.
What affects the price in Stanhope
What shapes the price:
- How accessible the joints are
- Site requirements such as inductions and permits
- Whether old sealant has to be cut out first
- Location, for remote and island sites
We don’t publish prices, because the scope varies so much from one building to the next. Call for a quote and we will price your job on its own details.
Sending details for a quote
However big the job, the same details help:
- The asbestos register, for older buildings
- Access details, including height
- Any specification or named product
- Drawings or a marked-up plan, if available
Quotes are fixed against the scope you send, so you know the figure before anyone is on site. To ask for one, call 01277 525 020 or email drawings and photos.
Compartments and services around Stanhope
Stanhope lies roughly 48 miles out from central London. Business park offices in the commuter belt are refitted as tenants change, and each fit-out adds services through compartment walls; the gaps need the specified seal. The 2 miles around Stanhope include two care or nursing homes. Care homes rely on fire-resisting walls and floors, and maintenance work that breaks through them leaves openings to seal.
Hotels such as Castle Hotel (to the north-east of Stanhope) rely on fire-resisting walls between bedrooms and corridors, and refits that add services leave penetrations to seal where fire-rated sealant is specified. Where a unit on an estate such as Ellingham Industrial Estate, 0.5 miles to the south-east of Stanhope, has fire-resisting walls between offices and warehouse, any new service through them should be sealed to the tested detail.
Stanhope is about 1 mile south-west of Ashford, in Kent. Businesses, contractors and managing agents in Stanhope use us for work on service penetrations. Stanhope is one of 931 places we cover in Kent. There’s a separate page for London, about 48 miles away.
Work on service penetrations is covered throughout TN23, whatever the building. Among the streets we cover are Green Lane, Cryol Road and Athol Road. Just outside Stanhope, we also work in Ashford (1 mile north-east), Park Farm (1 mile south-east), Kingsnorth (1 mile south), Newtown (1 mile east) and Great Chart (1 mile north-west). Nearby towns on our patch include Canterbury (14 miles north-east), Folkestone (14 miles east), Faversham (13 miles north), Hythe (11 miles south-east), Davington (13 miles north) and Preston (12 miles north).
Near you in Stanhope
Locally, jobs take us to sites close to The Beaver Inn, John Wallis Academy and Ashford Community Woodland. For rail, the closest station is Ashford International station, roughly 1.2 miles north-east of the centre. Other landmarks nearby include William Harvey Hospital (2.7 miles east) and Ashford Designer Outlet (1.1 miles east). Open spaces near Stanhope include Orlestone Forest.
How a job runs
Site rules come first: sign-in, induction and whatever permit system the building uses. Once we are cleared to begin, the joints are worked through in the order agreed with your site contact. For a site in Stanhope, we plan so the whole job is done in one go where possible. Photos with rough sizes let us arrive with everything needed.
- First we go through the drawings, schedule or specification for the seals and raise any questions before we price.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Unsuitable fillers and loose debris are taken out of each opening.
- Mineral wool or other backing goes in wherever the detail asks.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
Getting the site ready
- Let building users know which areas are affected
- For older buildings, check the asbestos register before work
- Tell us what induction or permit system the site runs
Quotes
A handful of photographs and a postcode is the fastest way to a quote. Upload them with the quote form, or speak to us on 01277 525 020 or email a schedule or drawings to discuss it first.
Related advice
Doing it in-house
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
What you see is the finished bead, but most of the work is hidden. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.
Surface by surface
Small ducts
Some fire-rated sealant details cover small ducts. Bigger ducts and fire-resisting ductwork are normally handled with other products and we flag that rather than guess.
Metal pipes
Metal pipes conduct heat, so their details often call for extra measures along the pipe, and the tested detail may ask for insulation beyond the wall. If the detail needs something beyond sealant, we tell you.
Work for main contractors and building owners
Main contractors use us as their sealant subcontractor on new-build and refurbishment projects. Programme, specification and site rules come first, with CSCS-carded applicators on site.
Planned maintenance programmes are welcome: resealing failed joints building by building, on a schedule that suits your budget. Sites in Stanhope can sit alongside others in a wider programme across Kent.