Fire Stopping in Norseman
Fire-rated and intumescent sealing of service penetrations and linear gaps in Norseman. CHAS accredited, Constructionline member, with a 12-month guarantee on workmanship.
- Seals that don’t match their tested detail
- Penetration schedules that need working through
- Builders’ foam or ordinary silicone in compartment walls
Need fire stopping in Norseman?
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Fire stopping in Norseman, done properly
Most of our fire stopping work happens after the building is up. Each new cable, pipe or data route cut through a fire-resisting wall leaves an opening behind, and they are easy to forget. Those on your schedule are closed with the specified product. If you’re dealing with head-of-wall gaps with no fire seal and seals that don’t match their tested detail, we can help. A single leaking joint is often how a building in Norseman first comes to us: we look at the rest while we’re there and tell you what we find.
Travel to smaller places like Norseman is planned so every penetration is sealed on one trip. Send the specification and photographs of the openings, with sizes if you have them.
The 12-month guarantee covers our workmanship: the preparation, the sealing and the tooling. It doesn’t extend to damage, other trades’ later work or movement the joint was never designed to take.
- Where
- Norseman (KW17)
- Region
- Orkney Islands
- Cover
- 12 months on every job
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Updated
- 3 November 2026
How a job runs
On arrival, we sign in, go through any site induction and check how permits are handled. Floors, finishes and fittings next to the joints are covered before anything is cut or cleaned, with the work itself normally taking a single visit for a short list of penetrations, or a phased programme for a whole building. For work around Norseman, we aim for one trip, which is why we ask for photographs and a full list first. External joints need a dry spell as well.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Getting the site ready
- Send asbestos survey details if the building is pre-2000
- Let us know about inductions and permits
- Warn occupants and staff about the work
Quotes
Let us know the site, the scope and your timescale, and we’ll put a fixed quote together. To get it moving, speak to us on 01277 525 020 or email drawings and photos.
Related advice
Places near Norseman
More services for Norseman
Do you need fire stopping in Norseman?
Linear gaps fail where a fire-resisting wall meets a slab, soffit or another wall. Deflection and building movement can open these gaps, and the wrong product can split as a result. The tested detail for a linear joint states the width and movement it covers.
Look out for the following:
- Builders’ foam or ordinary silicone in compartment walls
- Fire sealant pulled out of the opening
- Seals disturbed by maintenance and left open
- Penetration schedules that need working through
Around Norseman, we install fire-rated and intumescent sealant to the product’s tested detail wherever it is the specified product.
What your quote should include
- How they handle RAMS and site documents
- Their approach to joint depth and backing
- What level of public liability insurance do they hold?
- Whether old or failed sealant will be cut out, not overlaid
Fire stopping in Norseman: the local picture
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, with proprietary products, intumescent ones included, tested for their end use. We install what’s specified, to the product’s tested detail. Being on an island, Norseman means planning around ferry times as well as the weather. The specification and photographs of each penetration let us bring the right products first time.
Wherever the building is near Norseman, design and sign-off of fire stopping sit with the designer, fire engineer or building control; we install what has been specified.
Norseman is about 7 miles north-west of Kirkwall, in the Orkney Islands. We send applicators to Norseman for service penetrations. Norseman is one of 51 places in the Orkney Islands on our list.
Commercial sites across KW17 are covered. We also cover Isbister (1 mile east), Settiscarth (1 mile west), Gorseness (2 miles north-east), Tingwall (3 miles north-east) and Finstown (3 miles south) for service penetrations. Remote and island addresses take more planning, from travel and ferries to the weather, so give the site location in your enquiry.
Landmarks near Norseman
Nearby you will also find Corrigall Farm Museum (3.4 miles west) and Langskaill House (4.1 miles north-east). Not far away are Ward of Redland and Loch of Brockan.
Quoting for work in Norseman
Sealant work doesn’t have a standard rate, since sites vary so much. What we look at:
- Travel to remote or island sites
- Removal of failed or old sealant
- How much there is to seal
- Joint width, depth and condition
Every site prices differently: joint size, product, access and site hours all play a part. Send the details and a fixed figure follows.
Before you send an enquiry
However big the job, these details speed things up:
- Photos of the joints, close up and from further back
- The postcode of the building
- Whether an asbestos survey exists
- Drawings or a marked-up plan, if available
The quickest route to a quote is a few photographs and the site postcode. Upload them with the quote form, or speak to us on 01277 525 020 or email a schedule or drawings if you’d rather talk the job through.
How the job changes by surface
Metal pipes
Copper and steel pipes are a common service penetration for fire-rated sealant. The tested detail sets the pipe size range, gap, depth and whether insulation can stay on, so we check each one.
Small ducts
We seal around ducts only within what the tested detail covers. The ductwork, its supports and any dampers are for the ductwork contractor.
What sealant work can’t fix
Some faults sit outside our scope, and we say so rather than covering them up:
- Writing the fire-stopping specification
- Fire risk assessments, a job for a competent assessor
- Gaps in walls that were never built as compartment walls
If you’re not sure, just speak to us on 01277 525 020 or use the quote form and we’ll give you a straight answer before you book.
Joints and surfaces we work on
- Joints between fire-resisting walls and floors
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Service gaps in risers
- Linear gaps at wall heads
- Pipe penetrations
Common questions from Norseman clients
Can you produce the fire-stopping design for a job in Norseman?
No. The designer or fire engineer sets the detail and building control accepts it. We install what’s specified, to the product’s tested detail.
Do you work on the island where Norseman is?
Yes. We work across every Scottish council area, and that includes island locations such as Norseman. Ferry times and the weather set the plan, so we ask for photographs and a full list first.
What do you charge?
It depends on the job: the volume of work, the access, the specified product and how it’s phased. Call for a fixed quote and we will price it properly.
Which sealant will you use?
The specification comes first, if there is one. Without one, the joint decides: its movement, its surfaces and what it has to cope with.
Will you come and look before quoting?
It depends on the job. Straightforward work can often be priced from photos and measurements, and bigger or more complex jobs usually get a visit.
Can weather delay the job?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so external work may be moved if conditions aren’t right. Indoors, the weather is rarely a problem.
Do you offer coloured sealant?
That depends on the product. Some ranges are wide, others limited, so we’ll confirm the colours available for the specified product with the quote.
Site staff or a sealant specialist?
Using site staff can make sense for a small touch-up, but anything bigger is another matter: a specialist works through quantities efficiently, leaves a consistent finish and backs it with a 12-month guarantee.
For most general trades, sealant is a sideline. A specialist prepares properly, controls joint depth and picks a product with the right movement class, which is what makes a joint last.