Fire Stopping in New Alyth
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout New Alyth and nearby, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Fire stopping installed outside its tested range
- Fire sealant pulled out of the opening
- Seals disturbed by maintenance and left open
Fire stopping for New Alyth sites
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How we handle fire stopping in New Alyth
We should be clear about what we do and don’t do. The designer, fire engineer or building control decides which fire stopping is required. What we bring is careful installation of the specified sealant, to the maker’s guidance in New Alyth and nearby. We work on small duct penetrations where the tested detail allows, service gaps in risers and joints between fire-resisting walls and floors, and the usual reasons a site gets in touch are seals disturbed by maintenance and left open and hidden openings found during inspections. Searching for sealant specialists in New Alyth? Mastic Doctor has worked for contractors, FMs and building owners since 2005, CHAS accredited and a Constructionline member.
Hotels and care homes around smaller places like New Alyth often have services added during refurbishment. A round of checks after M&E work is good practice, and any gaps found are sealed where fire-rated sealant is specified.
Work we carry out in Perth and Kinross comes with a 12-month guarantee. Should something we installed fail, call the office on 01277 525 020 or send photos by email and we will come back to it.
- Where
- New Alyth (PH11)
- Wider area
- Perth and Kinross
- Cover
- 12 months on our workmanship
- Price
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Updated
- 3 November 2026
Should maintenance staff do it?
What you see is the finished bead, but most of the work is hidden. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.
For most general trades, sealant is a sideline. A specialist prepares properly, controls joint depth and picks a product with the right movement class.
Also near New Alyth
What else we do in New Alyth
Fire-rated sealing for New Alyth buildings
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, and products should be tested for their end use. We install what’s specified, to the product’s tested detail. The area within 2 miles of New Alyth holds several hotels. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail.
In a hotel such as Lands of Loyal Hotel, 1.2 miles to the north of New Alyth, new pipework or cabling through bedroom and corridor walls needs sealing with the specified product. Halls and meeting rooms at places like St Ninian's Episcopal Church sometimes gain new services, and any compartment wall crossed needs the specified seal.
New Alyth is about 4 miles north-east of Blairgowrie and Rattray, in Perth and Kinross. Businesses, contractors and managing agents in New Alyth use us for work on service penetrations. Our Perth and Kinross coverage takes in 114 places, large and small. We also cover Dundee, some 14 miles away.
Anyone looking for fire stopping in PH11 gets the same process as the rest of our area: send details, get a quote, we seal, guaranteed. We cover commercial and managed buildings on Smith Lane, Muirton Place and Bamff View. We also cover Alyth (1 mile north), Meigle (3 miles south-east), Ardler (4 miles south-east), Rattray (4 miles south-west) and Blairgowrie and Rattray (4 miles south-west). A short drive away, we cover Scone (15 miles south-west), Stanley (12 miles south-west), Errol (15 miles south), Luncarty (14 miles south-west), Bankfoot (13 miles south-west) and Longforgan (12 miles south).
Around New Alyth
Nearby you’ll also find Alyth Museum (0.8 miles north) and Blairgowrie Community Hospital (4.6 miles south-west). Not far away are Monk Myre and Hill of Alyth.
Our process
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Any old material is cut back to clean, sound faces, primer goes on where the manufacturer specifies it, and the sealant is tooled off neatly. Tell us who will meet us and how to get in at your building near New Alyth. That goes into the plan alongside the quote.
- We ask for the product and detail your designer has specified.
- We sort the openings by the detail each one needs.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
What we need from you
- Arrange parking or a loading space
- Make sure the joints can be reached
- For older buildings, check the asbestos register before work
Getting a fixed quote
Need a figure for a tender or a budget? We’ll quote against your scope and drawings that you can work with. For a chat about it beforehand, speak to us on 01277 525 020 or send details through our quote form.
Related advice
Common problems we fix in New Alyth
On a busy project, programme pressure can mean fire stopping is rushed or left to whichever trade is closest. That is when untested combinations creep in, which then have to be put right.
Clients typically get in touch after noticing one or more of the following:
- Unsealed openings around new pipes and cables
- Hidden openings found during inspections
- Fire-rated sealant that has cracked or shrunk back
- Head-of-wall gaps with no fire seal
On a hospital site such as Blairgowrie Community Hospital, 4.6 miles south-west of New Alyth, fire-rated sealant goes in where the specification calls for it, with the work planned around the estates team’s permits.
Questions to ask before you book
- How joint depth will be controlled
- Are they CHAS accredited or on Constructionline?
- Their plan for phasing and protecting the area
- Whether their applicators hold CSCS cards
After the work
Sealant joints are maintenance items, and how long they last depends on how they’re treated. Our advice:
- Look above ceilings when tiles are lifted for other jobs
- Record which product was used where
- Arrange inspection before areas are covered up
- Ask which product is in place before decorating
Keep the product data and installation details with the building’s fire safety information. It makes later repairs much easier to match.
Ask every contractor who works in risers or voids to report openings they create. It costs little and catches breaches early.
FAQs: New Alyth
Can you seal penetrations in a hotel in New Alyth after a refit?
Yes, where the specification calls for fire-rated sealant. Work is done room by room so the hotel keeps trading; design and sign-off stay with the designer and building control.
Would you work within a site like Blairgowrie Community Hospital?
Yes. We work in healthcare settings as well as offices and schools. Each area is agreed with the ward or department and the estates team in advance.
Is colour matching possible?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We confirm what’s available for the specified product when we quote.
How long do sealant joints last?
Nobody can honestly give a figure in years, since movement, weather, cleaning and use all affect it. Regular inspection is the best way to catch problems early.
What hours do you work?
The office is staffed Monday to Friday, from 8am until 5pm. Let us know your site hours and access windows, and the work will be planned around them.
Can you quote from photographs?
It depends on the job. Straightforward work can often be priced from photographs and measurements, and bigger or more complex jobs normally get a visit.
Do you guarantee your work?
Yes, for 12 months. If a joint fails because of how we installed it, we come back and put it right.
What affects the price in New Alyth
We price every job individually. The main factors are:
- Any access equipment needed
- Whether the work must be split into stages
- Backing rod, priming and other preparation
- Location, for remote and island sites
Small jobs and large programmes are priced from the same things: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote and we will put a fixed figure on it.
Details that help us quote
It doesn’t need to be a full survey. These details are enough to start:
- The type of building and who uses it
- Access details, including height
- A wide shot and a close-up of the area
- The asbestos register, for older buildings
For a fixed quote, phone 01277 525 020 or email drawings and photos, telling us the site location and the nature of the job. You can also send details through our quote form.
Surface by surface
Linear joints
Head-of-wall joints often have to absorb slab deflection. We use the product and backing the detail names for that movement, with no gaps along the run.
Masonry and concrete
Many seals are made in blockwork, brickwork or concrete slabs. Dust and debris are cleared from the opening, with backing added if the detail requires it.