Fire-rated sealing and fire stopping in Murcott, Oxfordshire
Fire-rated and intumescent sealing of service penetrations and linear gaps across Murcott, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Improvised or mixed-product fire seals
- Fire seals cut back for extra cables and never reinstated
- Openings found when ceilings come down for a refit
Fire stopping in Murcott
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Looking after the joints
For the best life from the joints:
- Agree the fire-stopping specification before services go in
- Put resealing into every M&E and fit-out package
- Record which product was used where
- Check with the data sheet before painting over fire sealant
Allow the manufacturer’s stated cure time before boxing in or decorating. Some fire-rated sealants accept paint and some don’t.
Keep a register of where seals are and what they are made of. It tells the next contractor exactly what to reinstate, and it helps at inspections.
About our fire stopping in Murcott
We should be clear about what we do and don’t do. Deciding the specification sits with the designer, the fire engineer and building control. What we bring is careful installation of the specified sealant, to the maker’s guidance. If you’re dealing with non-fire-rated filler around services and seals that don’t match their tested detail, we can help, on service gaps in risers, cable penetrations and pipe penetrations alike. Whoever orders the work in Murcott, the brief is usually the same: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
For a smaller site near Murcott, we plan to do all the penetrations in one go, so send the specification and photos first. Design and sign-off belong to the designer or building control; we install what’s specified.
Whoever the client is, the cover is the same: twelve months on the work we carried out. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Location
- Murcott (OX5)
- Wider area
- Oxfordshire
- Cover
- 12 months on our workmanship
- Price
- Fixed quote, scope in writing
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Our process
Before any cutting starts, the area is protected: tape along each joint edge and covers over finishes, stock and equipment close by. The work itself typically takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence, and we clear our waste as we work. Smaller jobs around Murcott can be grouped with others nearby. You’ll have a fixed quote before work starts.
- The specification and schedule come first, so we know which details apply.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned first.
- The specified backing and sealant go in to depth and are finished neatly.
- We tell you about openings that need a different product.
What we need from you
- Make sure the joints can be reached
- Send asbestos survey details if the building is pre-2000
- Tell us your opening times and when work is allowed
Request a quote
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To start the process, give us a call on 01277 525 020 or send photos by email.
Related advice
Fire stopping in Murcott: the local picture
Murcott lies roughly 51 miles out from central London. Business park offices in the commuter belt are refitted as tenants change, and each fit-out adds services through compartment walls; the gaps need the specified seal. For England, the fire stopping of penetrations is dealt with in Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. We install whatever has been specified, to the product’s tested detail.
Wherever services are added at a hospital such as Bicester Community Hospital, 4.1 miles to the north of Murcott, the compartment line has to be made good with the specified product. Buildings near Murcott get the fire-rated product that’s specified, installed to its tested detail.
Murcott is about 4 miles south of Bicester, in Oxfordshire. Looking for fire stopping in Murcott? We can help. Our Oxfordshire coverage takes in 423 places, from busy centres to rural villages. For work in that direction, see our Oxford page, about 7 miles away.
Commercial sites across OX5 are covered. Just outside Murcott, we also work in Fencott (1 mile north-west), Merton (1 mile north-west), Charlton-on-Otmoor (1 mile west), Upper Arncott (2 miles north-east) and Lower Arncott (2 miles north-east). Nearby towns on our patch include Oxford (7 miles south-west), Bicester (4 miles north), Abingdon-on-Thames (12 miles south-west), Witney (15 miles west), Thame (10 miles south-east) and Kidlington (6 miles west).
What’s near Murcott
Murcott’s nearest station is Islip station, roughly 3.7 miles west of the centre. Other landmarks nearby include Bicester Community Hospital (4.1 miles north) and Bicester Avenue (3.5 miles north). Not far away are Otmoor RSPB reserve and Graven Hill.
Surface by surface
Masonry and concrete
Block walls and concrete floors are common substrates for penetration seals. Dust and loose debris are cleared out of the opening, with backing added if the detail requires it.
Metal pipes
Heat travels along metal pipework, and the tested detail may ask for insulation beyond the wall. We follow whatever the detail requires and flag anything we can’t match.
Why act early in Murcott
Inspections and handover checks often pick up fire stopping. Late discoveries can delay handover while openings are reopened and resealed which is why earlier is better. Around Murcott, it’s better to renew all the failing joints at once. Photos of every joint help us quote for the whole job.
The product called for affects the cost, as does the preparation each joint needs, from cutting out to priming and backing rod. Access, phasing and site rules also count.
Why us?
- A fixed quote before work starts
- Public liability insurance in place
- CSCS-carded applicators
- One contact handling all your sites
Take a look at what affects the cost and our accreditations.
Your questions answered
Is hospital work, at somewhere like Bicester Community Hospital, something you do?
Yes, hospitals are one of the sectors we cover. Before anything starts, the estates team agrees permits, inductions and infection-control measures with us.
What does the BS 476 change mean for fire-rated sealant in Murcott?
From 2 September 2029, Approved Document B drops its BS 476 references in favour of BS EN 13501-2 classification, with transitional arrangements. The designer or fire engineer sets the specification, and we install the product to the manufacturer’s tested detail.
Are you fully insured?
Yes. Mastic Doctor is fully insured, public liability included.
Can the sealant be colour-matched?
That depends on the product specified. Some ranges offer many colours, others very few, so we will confirm the colours available for the specified product with the quote.
What hours do you work?
We’re in the office from 8am until 5pm, Monday to Friday. Let us know your site hours and access windows, and the work will be planned around them.
Do your applicators hold CSCS cards?
Yes. We use CSCS-carded applicators, which many sites require.
Is your workmanship covered by a guarantee?
Yes. Our workmanship is backed for 12 months.
Places near Murcott
What else we do in Murcott
Site staff or a sealant specialist?
General builders and handymen seal joints, but it isn’t their main trade. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint.
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and we will confirm the paperwork you need with the quote.
How the quote is worked out
These are the things that shape the price:
- How accessible the joints are
- Specialist products, such as fire-rated or hygienic sealants
- Backing rod, priming and other preparation
- Induction, permit and paperwork requirements
No two sites price the same: joint size, product, access and site hours all play a part. Send the details and a fixed figure follows.
Sending details for a quote
We can often quote from photos and a few details. It helps to include:
- The asbestos register, for older buildings
- Approximate linear metres or a joint schedule
- Any specification or named product
- Access details, including height
Send us photos, drawings or a joint schedule and a fixed quote comes back to you. If the job needs a look first, we’ll arrange a site visit.