Mimbridge fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps across Mimbridge, by CSCS-carded applicators. CHAS accredited and fully insured.
- Service penetrations left open after M&E works
- Head-of-wall gaps with no fire seal
- Fire-rated sealant that has cracked or shrunk back
Fire stopping across Mimbridge
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
When something else is needed
Our job is the joint, not everything around it. On its own, sealant can’t deal with:
- Reviewing a building’s overall fire safety
- Large openings beyond what any sealant detail covers
- Construction that lacks the fire resistance the seal relies on
Not sure which it is? You can ring 01277 525 020 or email the details over and we will tell you honestly before you book.
Where we work in Mimbridge
- Linear gaps at wall heads
- Service gaps in risers
- Joints between fire-resisting walls and floors
- Cable penetrations
- Pipe penetrations
- Small duct penetrations where the tested detail allows
About our fire stopping in Mimbridge
A fire-rated sealant is only one part of a tested system: its test evidence covers one product in one kind of wall or floor, with set services, gaps, depths and backing. Before we seal anything, we check the opening against the detail it is meant to follow, and raise it with you if it falls outside. We work on pipe penetrations, service gaps in risers and small duct penetrations where the tested detail allows, and the failures we are asked to look at most are openings left by services added after handover and openings found when ceilings come down for a refit. A single leaking joint is often how a building in Mimbridge first comes to us: we check the joints around it and give you an honest view of what needs doing now and what can wait.
For a smaller site near Mimbridge, we plan to do all the penetrations in one go, so send the specification and photographs first. We install to the specification and the manufacturer’s guidance, leaving design and sign-off with the designer and building control.
Our workmanship is guaranteed for 12 months, wherever the site is. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Location
- Mimbridge (GU24)
- Region
- Surrey
- Cover
- 12 months on every job
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Updated
- 3 November 2026
Towns and villages near Mimbridge
More services for Mimbridge
Surface by surface
Drylining partitions
Drylined fire walls are tested in a particular build-up. The sealant detail has to be tested in that wall type, with the stated board layers.
Linear joints
Head-of-wall joints often have to absorb slab deflection. The specified product and backing for that movement are what goes in, with no gaps along the run.
What sets the cost
These are the things that shape the price:
- Quantities, in metres or numbers
- The product specified
- Induction, permit and paperwork requirements
- How accessible the joints are
Pricing service penetrations depends on how many there are, their condition and the access. Ask us for a fixed quote.
What to include in your enquiry
To price the job accurately, we need a clear picture of the site. Send us:
- Whether an asbestos survey exists
- Approximate linear metres or a joint schedule
- Any dates the work must fit around
- A wide shot and a close-up of the area
Tell us about the building, the joints and when you need the work done, and a fixed quote will follow. To get it moving, phone 01277 525 020 or send photos by email.
Common questions from Mimbridge clients
Do you take on work at healthcare sites like Nuffield Health Woking Hospital?
Yes, provided the work is planned with the site’s estates team. Work is phased so departments keep running, under the site’s own rules.
What does the BS 476 change mean for fire-rated sealant in Mimbridge?
From 2 September 2029, Approved Document B drops its BS 476 references in favour of BS EN 13501-2 classification, with transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Which sealant will you use?
The specification comes first, if there is one. Without one, the joint decides: how much it moves, what it bonds to and whether it’s wet, trafficked or fire-rated.
What do you charge?
It depends on the job: the volume of work, the access, the specified product and how it’s phased. Call for a quote and we’ll price it properly.
What if there’s asbestos in the old mastic?
The duty to manage asbestos sits with the building’s dutyholder, so we’ll ask for the register before work on an older building. Work pauses if suspect material is found, until it has been tested.
Can one quote cover more than one building?
Yes. Multi-site work and planned programmes are a core part of the service, planned site by site to suit how each building is used.
Do you work to architects’ specifications?
Yes. Include it with the drawings when you ask for a quote, and the quote will be based on it.
Building owners, agents and FMs in Mimbridge
Agents, factors and owners’ representatives all follow the same route: send the details, accept a fixed quote, and we carry out and guarantee the work. We can agree access arrangements and keyholder contacts beforehand.
Main contractors use us as their sealant subcontractor, on new build and refurbishment alike. Programme, specification and site rules come first, and our applicators hold CSCS cards.
Fire stopping around Mimbridge: what changes locally
Mimbridge lies roughly 24 miles out from central London. Offices around the capital are refitted often, and the cabling that follows can breach fire-resisting walls. A number of hotels sit less than 2 miles from Mimbridge. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail.
In a school such as Woking High School, fire-rated sealant goes in around service penetrations where it is specified. Office fit-outs on sites such as Chobham Business Centre (1.1 miles north-east of Mimbridge) add cabling and pipework through fire-resisting walls, and fire-rated sealant goes in where the specification calls for it. Workshops and IT rooms at colleges like Woking College, 2.7 miles south-east of Mimbridge, are re-serviced often, leaving penetrations to seal.
Mimbridge is about 2 miles north of Woking, in Surrey. Mimbridge sits inside our coverage and the rest of Surrey, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. Across Surrey, 379 places are covered, including Mimbridge. Sites around Reading have their own page, about 19 miles away.
We take on service penetrations across the GU24 postcode area, for business premises of every kind. We cover commercial and managed buildings on Station Road, Philpot Lane and Mount Road and the roads nearby. Mimbridge sits on or close to the A3046. Sites close to Mimbridge are covered too, including Horsell (1 mile south-east), Goldsworth Park (2 miles south), Woking (2 miles south), Stonehill (2 miles north-east) and St John's (2 miles south). Bigger towns within reach include Guildford (6 miles south), Camberley (6 miles west), Epsom (13 miles east), Farnham (13 miles south-west), Ewell (14 miles east) and Egham (6 miles north).
What’s near Mimbridge
We work on buildings around Horsell CofE Aided Junior School, The Cricketers Public House and Milford Green and Coxhill Green, among other places. Mimbridge’s nearest station is Woking station, roughly 1.8 miles south-east. Other landmarks nearby include Chobham Museum (1.2 miles north-west) and Woking Community Hospital (2 miles south-east). Not far away are St Ann's Hill and Gracious Pond.
Diagnose, treat, sign off
At the end of each section, we remove the tape, clean down and inspect every joint. Where the sealant needs time to cure before use, we tell you and sign the area. Jobs in and around smaller places like Mimbridge are normally planned as a single visit, so we ask for photos and rough sizes first. Then the right materials arrive with us.
- The specification and schedule come first, so we know which details apply.
- We plan the sequence of floors, risers and voids with you.
- We compare every service penetration with its tested detail before sealing.
- Unsuitable material is removed and the opening cleaned first.
- Backing and fire-rated sealant are installed to the detail and tooled.
- Anything outside the detail is reported to you rather than sealed.
What we need from you
- Tell staff and tenants when we’ll be in
- Send asbestos survey details if the building is pre-2000
- Have the specification and drawings to hand
Request a quote
The quickest route to a quote is a few photos and the site postcode. Upload them with the quote form, or speak to us on 01277 525 020 or email drawings and photos if you’d rather talk the job through.
Related advice
Site staff or a sealant specialist?
Putting right a botched joint often costs more than sealing it well at the start, because the whole bead must be removed and the faces cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
The visible bead is only part of the job. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.