Fire Stopping in Millbrook
Planning work on a service penetration in Millbrook? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Damaged fire seals in risers and voids
- Builders’ foam or ordinary silicone in compartment walls
- Improvised or mixed-product fire seals
Fire stopping near Millbrook
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Fire stopping in Millbrook, done properly
Most of our fire stopping work happens after the building is up. New cable runs, replaced pipework and extra data routes all punch holes in compartment walls. Those on your schedule are closed with the specified product. The enquiries we see most involve unsealed penetrations discovered above suspended ceilings and fire stopping installed outside its tested range, on service gaps in risers, linear gaps at wall heads and cable penetrations. Looking for mastic applicators who cover Millbrook? We’ve been sealing commercial buildings since 2005.
Fire-rated sealing in a place like Millbrook is typically a single building at a time. With the specification and photographs of the gaps, we can give a fixed quote and bring the right products.
Our workmanship is guaranteed for 12 months, in Millbrook as everywhere else we work. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Where
- Millbrook (SO15, SO16)
- Wider area
- Southampton
- Cover
- 12 months on every job
- Price
- Quoted before any work starts
- Phone
- 01277 525 020
- Updated
- 3 November 2026
Quoting for work in Millbrook
Each job is priced on its own details. The main factors are:
- Quantities, in metres or numbers
- Removal of failed or old sealant
- Travel to remote or island sites
- Which sealant the job calls for
A quote for service penetrations depends on quantities, condition and access, and any specification that applies. Ask us for a fixed quote.
Sending details for a quote
For an accurate fixed quote, we need a clear picture of the site. Send us:
- The type of building and who uses it
- Specification clauses that apply
- A wide shot and a close-up of the area
- Approximate linear metres or a joint schedule
Send details, get a quote, we seal, guaranteed: that’s how every job runs. The first step is to ring 01277 525 020 or email the details over with what you know.
How a job runs
We bring the products specified for the job, along with primers and backing rod. Any old material is cut back to clean, sound faces, primer goes on where the manufacturer specifies it, and the sealant is tooled off neatly. For a site in Millbrook, we plan so the whole job is done in one go where possible. Photos with rough sizes let us arrive with everything needed.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- We compare every service penetration with its tested detail before sealing.
- Foam, ordinary sealant and debris come out so the seal starts clean.
- The specified backing and sealant go in to depth and are finished neatly.
- We tell you about openings that need a different product.
Preparing the site
- Share the asbestos register for older buildings
- Make sure the joints can be reached
- Let building users know which areas are affected
Quotes
Let us know the site, the scope and your timescale, and a fixed quote will follow. To get it moving, give us a call on 01277 525 020 or email drawings and photos.
Related advice
What happens if it’s left?
The longer openings stay, the more there tend to be: each new service adds to the list. Keeping on top of it after each round of works keeps the job small. In a smaller place such as Millbrook, getting a contractor back for a second visit takes time, so it’s worth dealing with every failing joint at once.
There’s no price list, since every building and every scope is different. Call for a quote.
What you get with us
- Failed material removed, not covered up
- Workmanship guaranteed for 12 months
- Work carried out by CSCS-carded applicators
- Products installed to the manufacturer’s instructions
See how commercial sealant jobs are priced and our accreditations.
Millbrook: questions and answers
Is a smaller place like Millbrook outside your area?
No. Small places get the same service as large ones. London and every South East county are within our area. Good photos up front let us bring everything on the first visit.
Is hospital work, at somewhere like Western Community Hospital, something you do?
Yes, hospitals are one of the sectors we cover. Each area is agreed with the ward or department and the estates team in advance.
Do you hold third-party fire-stopping installer certification?
No. We are not members of a third-party fire-stopping installer scheme. We are CHAS accredited and a Constructionline member, and our applicators are CSCS-carded. If your contract requires third-party installer certification, we’re not the right fit for that package.
How soon can the area be used again?
That comes down to the sealant and the temperature. Some take light use quickly, others need longer to cure, so we will confirm the curing time on the day.
Do you work to architects’ specifications?
Yes. Send it with your enquiry, and we will price the work to it.
Can you quote from photos?
Photos, drawings or a schedule are often enough to quote. Where they aren’t, we arrange a site visit.
Can you fire stop behind the services contractors?
Yes. Send the schedule or marked-up drawings and the specified product details and a fixed quote follows. We can follow the services contractor floor by floor so areas aren’t left open.
Should maintenance staff do it?
Putting right a botched joint often costs more than sealing it well at the start, because the whole bead must be removed and the faces cleaned back again. For that reason, many FMs and contractors use a sealant specialist from the outset.
General builders and handymen seal joints, but it isn’t their main trade. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint.
Building owners, agents and FMs in Millbrook
We work for building owners and managing agents on sealant work across single buildings or whole portfolios. One quote can cover more than one site, which keeps the paperwork simple.
When you manage a building on behalf of an owner, you need clear quotes and clear reporting. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative.
Towns and villages near Millbrook
Other services in Millbrook
Honest limits
Honesty saves time and money. New sealant won’t cure:
- Large openings beyond what any sealant detail covers
- Writing the fire-stopping specification
- Issuing fire ratings or certificates for seals
If in doubt, give us a call on 01277 525 020 or use the quote form and we’ll say what we think.
What we seal
- Service gaps in risers
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Pipe penetrations
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
Where services cross fire walls in Millbrook
For England, the fire stopping of penetrations is dealt with in Approved Document B. References to the older BS 476 classes are being removed from it from 2 September 2029, after which the European classification, BS EN 13501-2, is the route, subject to transitional arrangements. We install whatever has been specified, to the product’s tested detail. A 2-mile radius around Millbrook takes in a good number of hotels. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail.
Tenant changes at centres like Shirley Retail Park (to the north-east of Millbrook) often mean new services through walls between units. For a unit at a site such as Liners Industrial Estate (1 mile east of Millbrook), new power or data runs between office and warehouse can breach a compartment wall. For a site team at a college like Richard Taunton Sixth Form College, which lies north-east of Millbrook, fire-rated sealing is best scheduled after the summer works.
Millbrook is about 2 miles west of Southampton, in Southampton. Businesses, contractors and managing agents in Millbrook can call on us for service penetrations. Across Southampton, 30 places are covered, Millbrook among them.
Postcode districts covered here: SO15 and SO16 for service penetrations. If your site is on Mill Road, Mendip Road and Severn Road or close by, we can quote for service penetrations. Sites close to Millbrook are covered too, including Regents Park (1 mile north-east), Shirley (1 mile north-east), Freemantle (1 mile east), Maybush (1 mile north) and Redbridge (1 mile west). A short drive away, we cover Midanbury (4 miles east), Thornhill (5 miles east), Harefield (5 miles east), Itchen (4 miles east), Sholing (4 miles east) and Portswood (3 miles east).
Local landmarks in Millbrook
In Millbrook, that means premises near Millbrook Community School, Blacksmiths Arms and Regents Park Community College. The nearest railway station is Millbrook (Hants) station, about 0.8 miles south-east of the centre. Well-known places in the area include Marlands Shopping Centre (2 miles east) and Western Community Hospital (0.7 miles north). For a walk, there’s Testwood Lakes.