Fire stopping in Lower Hardres
Need fire stopping in Lower Hardres? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Unsealed openings around new pipes and cables
- Fire-rated sealant that has cracked or shrunk back
- Unsealed penetrations discovered above suspended ceilings
Fire stopping near Lower Hardres
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Fire stopping in Lower Hardres, done properly
Where pipes, cables and other services cross a compartment wall or floor, the opening around them has to be closed so fire and smoke can’t move between compartments. Our job is fitting fire-rated and intumescent sealant at those service penetrations, and along linear gaps, where it is the specified product. Each seal follows the manufacturer’s tested detail. We work on pipe penetrations, small duct penetrations where the tested detail allows and cable penetrations, and the failures we are asked to look at most are fire-rated sealant that has cracked or shrunk back and hidden openings found during inspections. A single leaking joint is often how a building in Lower Hardres first comes to us: we look at the rest while we are there and tell you what we find.
Barn and farm-building conversions near places like Lower Hardres often combine new partitions with old walls. A penetration seal only performs as tested if product, substrate, service, gap and depth all match the detail.
We stand behind the joints we seal: 12 months, guaranteed. It covers how we prepared and applied the sealant.
- Location
- Lower Hardres (CT4)
- Region
- Kent
- Cover
- 12 months on our workmanship
- Price
- A fixed quote before we start
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
When something else is needed
A few problems need another trade or a different fix, and we point that out rather than sealing over them:
- Fire risk assessments, a job for a competent assessor
- Issuing fire ratings or certificates for seals
- Plastic pipes whose detail calls for a collar or wrap
Not sure which it is? You can phone 01277 525 020 or email a schedule or drawings and we’ll tell you honestly.
Where we work in Lower Hardres
- Small duct penetrations where the tested detail allows
- Pipe penetrations
- Cable penetrations
- Service gaps in risers
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
Places near Lower Hardres
Other services in Lower Hardres
Looking after the joints
Regular inspection catches problems early. Specifically:
- Check risers and ceiling voids after each round of works
- Report damaged or disturbed seals as soon as they’re spotted
- Ask the designer to confirm details early on refits
- Get seals inspected before ceilings and boxing close
Keep the product data and installation details with the building’s fire safety information. Anyone resealing later needs to know which product and detail were used.
On fit-outs, get the fire-stopping specification agreed before the services go in. Details can then be picked to suit the actual pipes, cables and ducts, and installation follows the programme.
Surface by surface
Small ducts
Some fire-rated sealant details cover small ducts. Larger or fire-rated ductwork typically needs a different solution set by the designer and we flag that rather than guess.
Risers and ceiling voids
Openings above suspended ceilings are easy to miss. We follow your schedule area by area, and note anything we find that isn’t on it.
Where services cross fire walls in Lower Hardres
Central London is about 54 miles from Lower Hardres. Office refits around the commuter belt bring new cabling through fire-resisting walls; the gaps need the specified seal. In England, Approved Document B covers fire stopping of openings and penetrations. From 2 September 2029, BS 476 references are being taken out of Approved Document B, leaving BS EN 13501-2 classification as the route, subject to the Government’s transitional arrangements. What we install is set by the specification, and it goes in to the tested detail.
For a site team at a college like Canterbury College, 2.9 miles north of Lower Hardres, fire-rated sealing is best scheduled after the summer works. On estates like Wincheap Industrial Estate, 2.7 miles north of Lower Hardres, the wall between office and warehouse is often fire-resisting, and cables through it need the specified seal. Large healthcare estates like The Chaucer Hospital, 1.9 miles to the north of Lower Hardres, change their services often, so penetration seals are worth checking after M&E work.
Lower Hardres is about 3 miles south of Canterbury, in Kent. Lower Hardres sits inside our coverage, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. Across Kent, 931 places are covered, Lower Hardres among them. London is covered too, some 54 miles away.
If you need fire stopping in CT4, the process matches everywhere else we work: send details, get a quote, we seal, guaranteed. We also cover Street End (1 mile north), Pett Bottom (1 mile south-east), Nackington (1 mile north), Upper Hardres (1 mile south) and Petham (2 miles south-west) for service penetrations. Nearby towns on our patch include Ashford (11 miles south-west), Canterbury (3 miles north), Dover (12 miles south-east), Folkestone (11 miles south), Whitstable (8 miles north) and Deal (14 miles east).
Near you in Lower Hardres
In Lower Hardres, that means premises near The Duck pub, among other places. Lower Hardres’s nearest station is Canterbury East station, about 2.7 miles north. Nearby you will also find Kent and Canterbury Hospital (2.2 miles north) and Whitefriars Shopping Centre (2.9 miles north). For a walk, there’s Blean Woods RSPB Reserve.
Work for main contractors and building owners
CHAS accredited and a Constructionline member, we make supplier vetting simple. We are fully insured, and our insurance certificate can go with the quote.
Housing associations and managing agents often need work done across blocks and communal areas. Work can be phased so residents and staff keep access throughout, and each stage is agreed with your contact.
Lower Hardres: questions and answers
How does the move away from BS 476 affect penetration seals in Lower Hardres?
References to BS 476 classes are being removed from Approved Document B from 2 September 2029, after which BS EN 13501-2 classification is the route, subject to transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Can you work at a site such as Wincheap Industrial Estate, by Lower Hardres?
Yes. Our area takes in Lower Hardres and its surroundings, with estates and business parks such as Wincheap Industrial Estate included. Photos and a short description are enough for a first look.
What do you charge?
Each job is quoted on its own details. To get one, call 01277 525 020 or send details through our quote form.
Do you work in Lower Hardres?
Yes. We cover Lower Hardres, and you can ring 01277 525 020 or email a schedule or drawings to get started.
Does weather matter for sealant work?
It can, when the joints are outside. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so external work may be moved if conditions aren’t right. Internal work is far less affected.
Are you fully insured?
Yes. We’re fully insured, including public liability cover.
Can the sealant be colour-matched?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We confirm what’s available for the specified product when we quote.
How the quote is worked out
We price every job individually. The things that drive the figure:
- Joint width, depth and condition
- Working within restricted access windows
- How accessible the joints are
- Removal of failed or old sealant
A quote for service penetrations depends on quantities, condition and access, and any specification that applies. Ask us for a fixed quote.
Sending details for a quote
We can often quote from photos and a few details. It helps to include:
- Photos of the joints, close up and from further back
- When you need the work done
- The asbestos register, for older buildings
- Where the site is, with the postcode
Need a figure for a tender or a budget? We’ll quote against your scope and drawings you can plan around. If you have questions first, ring 01277 525 020 or email us.
Diagnose, treat, sign off
Before any cutting starts, the area is protected: tape along each joint edge and covers over finishes, stock and equipment close by. The work itself normally takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence, and our waste is bagged and taken away as we go. Jobs in and around smaller places like Lower Hardres are usually planned as a single visit, so we ask for photographs and rough sizes first. That way the right products come on the day.
- We read the specification, drawings or penetration schedule you send and raise any questions before we price.
- On site, each opening is checked against the tested detail it is meant to follow.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- We fit the backing the detail asks for, to the stated depth.
- We apply the specified sealant to the depth and around the services as the detail shows.
- If an opening needs something other than sealant, we tell you instead of improvising.
Preparing the site
- For older buildings, check the asbestos register before work
- Warn occupants and staff about the work
- Confirm the product named in the specification
Get a fixed quote
The quickest route to a quote is a few photographs and the site postcode. Send them through the quote form, or phone 01277 525 020 or email us to discuss it first.