Fire stopping in Hurlingham
Sealant work in Hurlingham for main contractors, managing agents and facilities managers: fire-rated and intumescent sealing of service penetrations and linear gaps, with a fixed quote first.
- Openings left by services added after handover
- Snag lists that include open service penetrations
- Non-fire-rated filler around services
Fire stopping near Hurlingham
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Fire stopping in Hurlingham
Where pipes, cables and other services cross a compartment wall or floor, the opening around them has to be closed so fire and smoke can’t move between compartments. Our part is installing fire-rated and intumescent sealant at those openings and along linear gaps, where the specification calls for it. We work to the product’s tested detail for every seal. Site teams most often ask us about improvised or mixed-product fire seals and old intumescent sealant that has split away, across pipe penetrations, cable penetrations and service gaps in risers. Searching for sealant specialists in Hurlingham? Mastic Doctor has worked for contractors, FMs and building owners since 2005, CHAS accredited and a Constructionline member.
After a fit-out or new cabling in a London building, risers and ceiling voids are where open service gaps tend to be found. If sealant is the specified product we fit it to its tested detail, and if the detail needs something else, you’ll hear it from us.
Every job we finish is backed by a 12-month workmanship guarantee. If our installation lets you down in that time, we return and fix it.
- Location
- Hurlingham (SW6, SW18, SW15)
- Wider area
- Greater London
- Guarantee
- 12 months on our workmanship
- Price
- Quoted before any work starts
- Phone
- 01277 525 020
- Updated
- 3 November 2026
On site: what to expect
A typical day starts with protection: tape along each joint edge and covers over finishes, stock and equipment close by. The work itself typically takes a single visit for a short list of penetrations, or a phased programme for a whole building, and our waste is bagged and taken away as we go. For a job in Hurlingham, access comes first. Send the building rules and access times with your enquiry.
- We read the specification, drawings or penetration schedule you send and raise any questions before we price.
- On site, each opening is checked against the tested detail it is meant to follow.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- Mineral wool or other backing goes in wherever the detail asks.
- We apply the specified sealant to the depth and around the services as the detail shows.
- If an opening needs something other than sealant, we tell you instead of improvising.
Preparing the site
- Make sure the joints can be reached
- Arrange parking or a loading space
- Tell us your opening times and when work is allowed
Get a fixed quote
Photos, drawings or a schedule of the joints and a fixed quote comes back to you. If the job needs a look first, we will arrange a site visit.
Related advice
FAQs: Hurlingham
Does your area include sites such as Hurlingham Business Park, near Hurlingham?
Yes. Estates, retail parks and business parks around Hurlingham, Hurlingham Business Park among them, are all within reach. Photos and a short description are enough for a first look.
Could you schedule work at a campus like BIMM University for the vacation?
Yes. We plan campus work around teaching, exams and residence turnarounds. Any paperwork you need, from RAMS to our insurance certificate and CSCS details, is confirmed with the quote.
Which standards are fire seals tested to?
BS EN 1366-3 covers penetration seals and BS EN 1366-4 covers linear joints. Classification follows BS EN 13501-2. That rating only holds when the product is installed to its tested detail.
When is resealing likely to be due?
It depends on movement, UV and weather, cleaning, traffic and the product. Sealant joints are maintenance items, so inspect them regularly.
Does the weather affect the work?
For external joints, yes. Sealant needs a dry joint and a temperature within the product’s range, so damp, frosty or very cold days can stop external work. Internal work is rarely affected.
How soon can the area be used again?
Curing time varies by product, and we confirm it on the day, and sign any area that should be left alone.
What changes on 2 September 2029?
It mainly affects England, where Approved Document B is dropping its BS 476 references from 2 September 2029. Classification to BS EN 13501-2 becomes the expected evidence. Scotland follows its own Technical Handbook, including clause 2.1.14 on service penetrations.
Also near Hurlingham
What else we do in Hurlingham
After the work
Every sealant joint needs some looking after, and their life depends on movement, exposure, cleaning and use. Our advice:
- Put resealing into every M&E and fit-out package
- Get seals inspected before ceilings and boxing close
- Don’t let anyone top up a fire seal with the wrong product
- Report damaged or disturbed seals as soon as they’re spotted
After the work, brief anyone else working in the area that the openings are now sealed. If a seal has to be opened for a new service, it should be reinstated to the same detail, by someone who knows the system.
Write fire stopping into the scope of any work crossing a compartment wall or floor. Then the seal goes in while the area is open.
Penetration seals near Hurlingham
Plenty of hotels sit less than 2 miles from Hurlingham. A hotel refit often runs new services through compartment walls between bedrooms and corridors, and each opening needs the specified seal. London’s office and residential buildings are refitted constantly, and each round of cabling or pipework can leave open penetrations. We install fire-rated sealant where it is specified and work within the building manager’s permit system.
Residences at universities like BIMM University, 0.6 miles north of Hurlingham, have compartment walls that must be resealed whenever services change. Workshops and IT rooms at colleges like South Thames College Wandsworth Campus (to the south of Hurlingham) are re-serviced often, leaving penetrations to seal. In a retail centre such as Kensington Arcade (2.1 miles north of Hurlingham), any fire-resisting wall between units that is crossed by new services needs sealing to the tested detail.
Hurlingham is about 2 miles south of Kensington, in Greater London. Commercial clients in Hurlingham use us for work on service penetrations. Across Greater London, 764 places are covered, including Hurlingham.
We cover the SW6, SW18 and SW15 postcode districts. We cover commercial and managed buildings on Buer Road, Ewald Road and Dolby Road and the roads nearby. Main routes into Hurlingham include the A304. Close to Hurlingham, our area also takes in Parsons Green (1 mile north), Walham Green (1 mile north-east), Chelsea Harbour (1 mile east), Sands End (1 mile east) and West Brompton (1 mile north). Bigger towns within reach include London (5 miles north-east), City of Westminster (4 miles north-east), Marylebone (4 miles north-east), St Pancras (5 miles north-east), Shoreditch (6 miles north-east) and Walthamstow (11 miles north-east).
What’s near Hurlingham
Locally, jobs take us to sites close to Duke of Cumberland pub, Queensmill School and Lady Margaret School, among other places. Hurlingham’s nearest station is Imperial Wharf station, roughly 0.8 miles east. Other landmarks nearby include Putney Exchange (0.9 miles south-west) and Chelsea Stadium Tour And Museum (0.8 miles north-east). Green spaces nearby include Battersea Park Lake and WWT London Wetland Centre.
What sealant work can’t fix
A proper diagnosis includes knowing what sealant can’t do. We’ll tell you if the real problem is one of these:
- Walls or floors that aren’t fire-resisting to begin with
- Approving the work on behalf of building control
- Large openings beyond what any sealant detail covers
If in doubt, call 01277 525 020 or use the quote form and we will say what we think.
Where we work in Hurlingham
- Linear gaps at wall heads
- Service gaps in risers
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Pipe penetrations
Leave it or put it right?
Fire stopping is a regular point raised at inspections and handover. Late discoveries can delay handover while openings are reopened and resealed, so earlier action pays back. In Hurlingham, each extra visit means more notices, permits and disruption, so a proper job first time, with the old sealant fully removed, is worth it.
Quantities, awkward access and phased working all shape the price. Site requirements like inductions and permits play a part as well.
Why appoint us
- Products installed to the manufacturer’s instructions
- One phone line for London, the South East and Scotland
- Failed material removed, not covered up
- Over 20 years of commercial sealing
See our cost guide or our accreditations.
How the quote is worked out
These are the things that shape the price:
- How accessible the joints are
- Specialist products, such as fire-rated or hygienic sealants
- Working within restricted access windows
- Site requirements such as inductions and permits
A quote for service penetrations depends on how many there are, their condition and the access, plus any specification you are working to. Ask us for a fixed quote.
Sending details for a quote
A good diagnosis starts with the right details. Tell us:
- What the building is and how it’s used
- Where the site is, with the postcode
- Clear photographs of the problem areas
- Any specification or named product
A good quote starts with a clear picture: the joints involved, quantities, access and the product called for. Share whatever details you have and we’ll fill any gaps with a visit.
Should maintenance staff do it?
Paperwork matters too. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and our CSCS-carded applicators are used to working under those rules.
A short, simple internal joint is often within reach of a maintenance team. The usual problems come from preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.