Fire-rated sealing and fire stopping in Elmer, West Sussex
Fire stopping in Elmer, backed by over 20 years in commercial sealing. Fully insured, with a 12-month guarantee.
- Fire seals cut back for extra cables and never reinstated
- Open linear gaps along the top of fire-resisting walls
- Openings found when ceilings come down for a refit
Fire stopping across Elmer
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Compartments and services around Elmer
Central London is about 54 miles from Elmer. Offices around the capital are refitted often, and the cabling that follows can breach fire-resisting walls. For England, the fire stopping of penetrations is dealt with in Approved Document B. Its BS 476 references are being withdrawn from 2 September 2029, with BS EN 13501-2 classification taking over, subject to transitional arrangements. What we install is set by the specification, and it goes in to the tested detail.
Residences at universities like University of Chichester (Bognor Campus), 2.4 miles west of Elmer, have compartment walls that must be resealed whenever services change. At a healthcare site like Bognor Regis War Memorial Hospital, 2.9 miles to the west of Elmer, new services through compartment walls are a constant, and each needs the specified seal.
Elmer is about 3 miles east of Bognor Regis, in West Sussex. Our applicators travel to Elmer for work on service penetrations. Elmer is one of 373 places in West Sussex on our list for service penetrations. Our Portsmouth page has more on work in that area, about 20 miles away.
Anyone looking for fire stopping in PO22 gets the same process as the rest of our area: details, then a fixed price, then sealing and a 12-month guarantee. For a building on Elmer Road, Ancton Lane and East Avenue or nearby, we can quote for service penetrations. Nearby places we also cover include Middleton-on-Sea (1 mile west), Bilsham (1 mile north), Atherington (1 mile north-east), Flansham (2 miles north-west) and Horsemere Green (2 miles north-east) for service penetrations. Bigger towns within reach include Worthing (9 miles east), Bognor Regis (3 miles west), Chichester (8 miles north-west), Selsey (9 miles south-west), Littlehampton (4 miles east) and Shoreham-by-Sea (15 miles east).
What’s near Elmer
Recent enquiries here include premises near Felpham Community College. The nearest railway station is Ford station, roughly 2.9 miles north-east of the centre. Other landmarks nearby include Bognor Regis Museum (3.1 miles west) and Bognor Regis War Memorial Hospital (2.9 miles west).
How we handle fire stopping in Elmer
Where pipes, cables and other services cross a compartment wall or floor, the opening around them has to be closed so fire and smoke can’t move between compartments. Our job is fitting fire-rated and intumescent sealant at those service penetrations, and along linear gaps, where it is the specified product. Each seal follows the manufacturer’s tested detail, not a rule of thumb. If you have fire-stopping items raised at inspection or handover and seals that don’t match their tested detail, we can put it right, whatever the surface. Searching for sealant specialists in Elmer? Mastic Doctor has worked for contractors, FMs and building owners since 2005.
Converted and extended buildings around places like Elmer can mix old and new construction, so the wall or floor a service passes through isn’t always what the drawings assume. The right product depends on the wall or floor and the services passing through, and we’ll tell you if the detail calls for something other than sealant.
The 12-month guarantee covers our workmanship: preparation, application and finish. Damage, later alterations by others and movement beyond what the joint was designed for sit outside it.
- Where
- Elmer (PO22)
- Region
- West Sussex
- Cover
- A 12-month guarantee
- Price
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Cost factors for service penetrations
Your fixed quote is built from the real scope. It takes account of:
- Working within restricted access windows
- Access and working height
- Quantities, in metres or numbers
- Location, for remote and island sites
The product called for affects the cost, as does the preparation each joint needs. Access, phasing and site requirements come into it too.
Sending details for a quote
It doesn’t need to be a full survey. These details are enough to start:
- Rough lengths or quantities, or drawings if you have them
- Photos of the joints, close up and from further back
- The asbestos register, for older buildings
- How the joints are reached, and at what height
Every quote starts with the facts: the joints involved, quantities, access and the product called for. Share whatever details you have and we will fill any gaps with a visit.
When it isn’t the sealant
Our job is the joint, not everything around it. Sealant alone won’t deal with:
- Fire risk assessments, a job for a competent assessor
- Plastic pipes whose detail calls for a collar or wrap
- Deciding what a wall or floor needs, which belongs to the designer
If you are not sure, just speak to us on 01277 525 020 or send details through our quote form and we’ll give you a straight answer before you book.
Where we work in Elmer
- Cable penetrations
- Service gaps in risers
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Pipe penetrations
- Linear gaps at wall heads
Other services in Elmer
What happens if it’s left?
A seal that doesn’t match its tested detail gives false comfort. Correcting it means cutting it out and starting again with the specified product, so it makes sense to get it right first time. A failed joint lets water into a building whatever its size. Catching it early means a reseal rather than repairs.
There’s no price list, because the scope varies so much from one building to the next. Call for a quote.
What you get with us
- One phone line for London, the South East and Scotland
- Workmanship guaranteed for 12 months
- Public liability insurance in place
- Failed material removed, not covered up
Take a look at how commercial sealant jobs are priced or our accreditations.
How a job runs
On arrival, we sign in, go through any site induction and check how permits are handled. Floors, finishes and fittings next to the joints are covered before any cutting starts, with the work itself normally taking a single visit for a short list of penetrations, or a phased programme for a whole building. What matters most for a job in Elmer is a clear list of what needs doing, so send photos of each area. You will then get a fixed price for the work.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- We compare every service penetration with its tested detail before sealing.
- Unsuitable material is removed and the opening cleaned so the seal starts clean.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
Getting the site ready
- Send your site hours and access windows
- Tell staff and tenants when we will be in
- Point out any areas we must not close
Getting a fixed quote
The quickest route to a quote is a few photographs and the site postcode. Send them through the quote form, or speak to us on 01277 525 020 or send details through our quote form if you’d rather talk the job through.
Read more
What we are called out for in Elmer
Most open service penetrations are left by later work. New cabling, rerouted pipework or a data route drilled through a riser leaves an opening that nobody returns to. Over a few years of fit-outs, a wall can collect a lot of these.
Site and facilities staff are often the first to spot these:
- Open linear gaps along the top of fire-resisting walls
- Fire-stopping items raised at inspection or handover
- Improvised or mixed-product fire seals
- Builders’ foam or ordinary silicone in compartment walls
In a hotel such as Ancton House Hotel, under half a mile to the north of Elmer, new pipework or cabling through bedroom and corridor walls needs sealing with the specified product.
Before you book anyone
- Whether old or failed sealant will be cut out, not overlaid
- Will CSCS-carded applicators be on site?
- Can the work be phased to keep areas open?
- Their pre-qualification and accreditations
After the work
Cleaning and maintenance staff play a part too. Share these points with them:
- Ask the designer to confirm details early on refits
- Report damaged or disturbed seals as soon as they’re spotted
- Record which product was used where
- Arrange inspection before areas are covered up
Give the sealant its full cure time before ceilings, boxing or decoration go over it. Not every fire-rated product can be painted.
Write fire stopping into the scope of any work crossing a compartment wall or floor. That way the opening is sealed while the trade and access are still there, not months later.
Common questions from Elmer clients
Is Elmer off your patch?
Not at all. Elmer is within our area. London and every South East county are within our area. Where we can, we group nearby jobs to make the most of each trip.
Is Rudford Industrial Estate, near Elmer, within your area?
Yes. Estates, retail parks and business parks around Elmer, Rudford Industrial Estate among them, are all within reach. Send details of the unit and the work through our quote form for a quick quote.
Can you fire stop behind the services contractors?
Yes. Share the penetration schedule and product details and a fixed quote follows. Work can run area by area behind the M&E trades keeping pace with the programme.
Do you take on multi-site work?
Yes. We take on portfolio and planned maintenance work, with each site phased to suit its occupants.
Can you send site paperwork?
Tell us what site paperwork you need (RAMS, insurance certificate, CSCS details) and we’ll confirm with the quote.
How long do sealant joints last?
There isn’t a single answer, because life depends on how much the joint moves, how exposed it is and how it’s cleaned and used. Regular checks let you plan resealing before leaks or damage.
Can the sealant be colour-matched?
In many cases, yes. Many products come in a range of standard colours, and matching to RAL references or surrounding finishes is often possible. We will confirm the colours available for the specified product.