Fire-rated sealing and fire stopping in Eastwood, Kent
Fire-rated and intumescent sealing of service penetrations and linear gaps across Eastwood, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Builders’ foam or ordinary silicone in compartment walls
- Penetration schedules that need working through
- Fire-rated sealant that has cracked or shrunk back
Need fire stopping in Eastwood?
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Common problems we fix in Eastwood
When a seal departs from its tested detail, the evidence no longer covers it. An oversized gap, too shallow a bead, missing backing or two makers’ products combined are the usual culprits.
Site and facilities staff are often the first to spot these:
- Unsealed openings around new pipes and cables
- Hidden openings found during inspections
- Seals disturbed by maintenance and left open
- Fire stopping installed outside its tested range
Tenant changes at parks like Roebuck Business Park (2.6 miles north of Eastwood) bring new data and services, and openings through fire-resisting walls need the specified seal.
What your quote should include
- Are they CHAS accredited or on Constructionline?
- How the joint faces will be prepared and primed
- Their approach to joint depth and backing
- Who will actually carry out the work
Fire stopping in Eastwood
Our applicators are CSCS-carded, and we are CHAS accredited and a Constructionline member. We don’t hold a third-party fire-stopping installer certificate. We install the specified fire-rated sealant to its tested detail, and our workmanship carries a 12-month guarantee. If you have seals disturbed by maintenance and left open and expanding foam used as fire stopping, we can put it right. Most enquiries from Eastwood start with one failed joint and grow into a wider look at the building: we look at the rest while we’re there and tell you what we find.
A job near Eastwood is usually planned around one visit, with the specification and photos sent in advance. Design and sign-off belong to the designer or building control; we install what’s specified.
We sign every job off with a 12-month guarantee. The promise is simple: if our work fails within that year, we put it right.
- Location
- Eastwood (ME17)
- Wider area
- Kent
- Cover
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Also near Eastwood
Also in Eastwood
After the work
Sealant joints are maintenance items, and their life depends on movement, exposure, cleaning and use. Our advice:
- File the specified details where the next contractor can find them
- Ask the designer to confirm details early on refits
- Treat an open penetration as a priority repair
- Leave fire sealant to cure fully before covering it
Give the sealant its full cure time before ceilings, boxing or decoration go over it. Not every fire-rated product can be painted.
Ask every contractor who works in risers or voids to report openings they create. Small habits like this stop openings building up.
Doing it in-house
What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are easy to get wrong without experience.
Paperwork matters too. Many sites expect CSCS cards, RAMS and proof of insurance, and our CSCS-carded applicators are used to working under those rules.
What happens if it’s left?
It is cheaper to seal service penetrations as each services package finishes than to come back for them later. While the area is still open, every opening is easy to see and reach, and the right detail can be checked at the time. Halls, stores and units around places like Eastwood may not be checked every day, so a failed joint can leak for a while before anyone sees it. Resealing early avoids that.
Every site prices differently: the joint sizes, the specified product, access and working hours each have a bearing. Send the details and a fixed figure follows.
Why appoint us
- Failed material removed, not covered up
- Public liability insurance in place
- One contact handling all your sites
- 12 months’ guarantee on every job
See how commercial sealant jobs are priced and how we’re accredited.
What we can’t put right
Some faults sit outside our scope, and we say so rather than covering them up:
- Deciding what a wall or floor needs, which belongs to the designer
- Plastic pipes whose detail calls for a collar or wrap
- Issuing fire ratings or certificates for seals
Not sure which it is? You can give us a call on 01277 525 020 or use the quote form and we’ll tell you honestly.
Joints and surfaces we work on
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
- Cable penetrations
- Pipe penetrations
- Service gaps in risers
- Small duct penetrations where the tested detail allows
Fire stopping around Eastwood: how the place shapes the job
Eastwood lies roughly 38 miles out from central London. Offices around the capital are refitted often, and the cabling that follows can breach fire-resisting walls. Fire stopping of openings and penetrations in England falls under Approved Document B. References to the older BS 476 classes are being removed from it from 2 September 2029, after which the European classification, BS EN 13501-2, is the route, subject to transitional arrangements. Our part stays the same: the specified product, installed to its tested detail.
Campus buildings at universities such as Canterbury Christ Church University (to the north of Eastwood) see constant changes to data and services, and fire-rated sealant goes in around new penetrations where it is specified. Schools such as Ulcombe Church of England Primary School often have new data and services installed during holidays, and penetrations through fire-resisting walls should be checked afterwards.
Eastwood is about 7 miles south-east of Maidstone, in Kent. We cover commercial sites throughout Eastwood, whether it’s a single job or part of a planned programme. Eastwood is one of 931 places in Kent on our list. Our London page has more on work in that area, about 38 miles away.
Business premises anywhere in ME17 are within our area. We also cover Broadstone (1 mile south-east), Grafty Green (1 mile east), Ulcombe (1 mile north-west), Fairbourne Heath (1 mile north) and Liverton Street (1 mile north-east) for service penetrations. Nearby towns on our patch include Maidstone (7 miles north-west), Ashford (10 miles south-east), Sittingbourne (10 miles north), Faversham (12 miles north-east), Kings Hill (12 miles north-west) and Davington (12 miles north-east).
Around Eastwood
Locally, jobs take us to sites close to The Provender Public House. The closest station to Eastwood is Harrietsham station, roughly 2.8 miles north. Other landmarks nearby include The Dog Collar Museum (3.2 miles north-west) and Coldbridge Castle (1.6 miles east).
FAQs: Eastwood
How does the move away from BS 476 affect penetration seals in Eastwood?
Approved Document B loses its BS 476 references from 2 September 2029, and BS EN 13501-2 becomes the route, subject to transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Can work at a site such as Canterbury Christ Church University fit around teaching?
Yes. Tell us the term dates, vacation periods and access windows, and we will plan the work around them. Tell us which site documents you need, such as RAMS, our insurance certificate or CSCS details, and they’re confirmed with the quote.
Do your applicators hold CSCS cards?
Yes. Our applicators hold CSCS cards, which many sites require.
Is Eastwood in your area?
Yes. Eastwood falls within our area, and you can give us a call on 01277 525 020 or email us to get started.
Can you work to our specification?
Yes. Send it with your enquiry, and we will price the work to it, flagging anything that needs clarifying.
Can you quote from photographs?
Photos, drawings or a schedule are often enough to quote. Where they aren’t, we arrange a site visit before quoting.
How do you choose the sealant?
If the job is specified, we follow the specification. Otherwise, we recommend a product to suit the joint’s movement, the substrate and the conditions, following the manufacturer’s guidance.
On site: what to expect
Where the site stays busy, we agree a sequence with your contact so the disruption stays in one area at once. Each section is protected, cleaned back and sealed, then handed back before we move to the next. For work around Eastwood, we aim to finish in one visit, so photos and measurements up front really help. That way the right products come on the day.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Where the detail needs backing, it goes in at the stated depth.
- We gun the sealant in to the specified depth around each service and tool it.
- Completed areas are checked with you, with the records agreed when we quoted.
Before we start on site
- Send any specification or drawings in advance
- Make sure the joints can be reached
- Tell staff and tenants when we will be in
Quotes
For a fixed quote, call the office on 01277 525 020 or email the details over. Our quote form is another easy route.