Cuminestown fire stopping
Fire stopping for Cuminestown, from a contractor working since 2005. Fully insured, with a 12-month guarantee.
- Damaged fire seals in risers and voids
- Penetration schedules that need working through
- Open linear gaps along the top of fire-resisting walls
Fire stopping across Cuminestown
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Questions about Cuminestown
Is Cuminestown off your patch?
No. Small places get the same service as large ones. Our area covers all of Scotland, cities, towns and islands alike. Send photographs and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
Which Scottish guidance covers penetration seals in Cuminestown?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
Do your applicators hold CSCS cards?
Yes. Should the site need card details in advance, tell us and we will confirm them with the quote.
Can the building stay open while you work?
Usually, yes. We phase the work so most of the building stays in use, with each area protected and signed.
How long does a typical visit take?
That varies with the scale of the job, but the work normally takes anything from one day to a planned run of visits, depending on the number of seals and the access. For bigger or phased jobs, we will set out a timescale with the quote.
When can you be on site?
The office is staffed Monday to Friday, from 8am until 5pm. Let us know your site hours and access windows, and the work will be planned around them.
Is any job too small?
We quote for single jobs as well as large packages and programmes. Send details for a fixed quote.
About our fire stopping in Cuminestown
No fire sealant works on its own: its test evidence covers one product in one kind of wall or floor, with set services, gaps, depths and backing. Before we seal anything, we check the opening against the detail it is meant to follow, and raise it with you if it falls outside. If you’re dealing with seals disturbed by maintenance and left open and openings found when ceilings come down for a refit, we can help. Looking for mastic applicators who cover Cuminestown? We’ve been sealing commercial buildings since 2005.
For a building near Cuminestown, we plan fire-rated sealing so it’s finished in one visit where possible. Photos of the gaps, the services and the wall or floor type help us bring the right products.
Building owners and contractors get the same cover: a 12-month guarantee on our workmanship. It doesn’t extend to damage, faults in the building or work by others, and we are upfront about that.
- Location
- Cuminestown (AB53)
- Wider area
- Aberdeenshire
- Cover
- A 12-month guarantee
- Price
- A fixed quote before we start
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Nearby places to Cuminestown
Also in Cuminestown
After the work
Problems stay small when the joints are checked regularly. Specifically:
- Ask the designer to confirm details early on refits
- Foam or ordinary sealant is never a fire-seal repair
- Make fire stopping part of every scope that crosses a fire-resisting wall
- Get seals inspected before ceilings and boxing close
Store the specified product details somewhere the next contractor can find them. Anyone resealing later needs to know which product and detail were used.
Keep a register of where seals are and what they are made of. It tells the next contractor exactly what to reinstate.
Compartments and services around Cuminestown
Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, with proprietary products, intumescent ones included, tested for their end use. Where fire-rated sealant is specified, that’s what we install, to the tested detail.
On a hospital site such as Turriff Cottage Hospital (4.4 miles west of Cuminestown), fire-rated sealant goes in where the specification calls for it, with the work planned around the estates team’s permits.
Cuminestown is about 15 miles south-west of Fraserburgh, in Aberdeenshire. Cuminestown sits inside our coverage and the rest of Aberdeenshire, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. Cuminestown is one of 179 places in Aberdeenshire on our list. Our Aberdeen page has more on work in that area, about 28 miles away.
If you need fire stopping in AB53, the process matches everywhere else we work: send details, get a quote, we seal, guaranteed. If your site is on High Street, Main Street and Plane Trees or close by, send details and we will quote for service penetrations. Just outside Cuminestown, we also work in Garmond (1 mile north), New Byth (2 miles north-east), Turriff (5 miles west), Turfhill (5 miles south-east) and New Deer (6 miles east). A short drive away, we cover Fraserburgh (15 miles north-east), Ellon (15 miles south-east), Banff (11 miles north-west), Macduff (11 miles north-west), Oldmeldrum (14 miles south) and Mintlaw (12 miles east). Remote and island addresses take more planning, from travel and ferries to the weather, so mention the location when you give us a call on 01277 525 020 or send details through our quote form.
Landmarks near Cuminestown
Well-known places in the area include Turriff Cottage Hospital (4.4 miles west) and Delgatie Castle (3 miles west).
Our process
Before any cutting starts, the area is protected: tape along each joint edge and covers over finishes, stock and equipment close by. The work itself normally takes anything from one day to a planned run of visits, depending on the number of seals and the access, and our waste is bagged and taken away as we go. For work around Cuminestown, we aim for one trip, so photos, sizes and a full list matter. External joints need a dry spell as well.
- We read the specification, drawings or penetration schedule you send and ask about anything unclear.
- On site, each opening is checked against the tested detail it is meant to follow.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- We fit the backing the detail asks for, to the stated depth.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
Getting the site ready
- Make sure the joints can be reached
- Send your site hours and access windows
- Let us know about inductions and permits
Get a fixed quote
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to speak to us on 01277 525 020 or email drawings and photos with what you know.
Read more
When to call us in Cuminestown
Linear gaps fail where a fire-resisting wall meets a slab, soffit or another wall. Movement in the frame or slab can open the joint, and the wrong product can split as a result. Linear joint details set a width range and movement capability, and the seal has to sit within them.
If one of these sounds familiar, it’s time for a closer look:
- Fire sealant pulled out of the opening
- Head-of-wall gaps with no fire seal
- Improvised or mixed-product fire seals
- Builders’ foam or ordinary silicone in compartment walls
Older community buildings such as Monquhitter Parish Church that have been rewired or given new heating can have service gaps through walls worth checking against the specification.
Comparing quotes
- The terms of the workmanship guarantee
- What level of public liability insurance do they hold?
- Whether primer will be used where the manufacturer specifies it
- Are they CHAS accredited or on Constructionline?
For managing agents and facilities managers
Building owners and managing agents use us on everything from one building to a spread of sites around Cuminestown. One quote can cover more than one site, which keeps the paperwork simple.
Main contractors use us as their sealant subcontractor on new-build and refurbishment projects. We work to your programme, your specification and your site rules, with CSCS-carded applicators on site.
Cost factors for service penetrations
We price every job individually. The main factors are:
- Access and working height
- Whether the work must be split into stages
- Which sealant the job calls for
- The size and state of each joint
What a job costs comes down to how many linear metres there are, what has to come out first and how the joints are reached. Call for a quote once you have the details.
Details that help us quote
A few photos plus some basic facts will normally do. It helps to include:
- Asbestos survey details if the building is older
- What the building is and how it’s used
- Specification clauses that apply
- How the joints are reached, and at what height
A handful of photographs and a postcode is the fastest way to a quote. Send them through the quote form, or phone 01277 525 020 or email the details over if you’d rather talk the job through.
How the job changes by surface
Masonry and concrete
Core-drilled holes are neat; broken-out ones rarely are. The gap is measured at the widest point against the detail’s limits, and any that don’t are flagged.
Risers and ceiling voids
Risers and ceiling voids hold most of a building’s service penetrations. Access is often tight, so we agree it with you in advance, including keys, permits and any isolations.