Fire stopping in Burray Village
Work needed on a service penetration in Burray Village? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Unsealed penetrations discovered above suspended ceilings
- Expanding foam used as fire stopping
- Snag lists that include open service penetrations
Fire stopping in Burray Village
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
How we handle fire stopping in Burray Village
Fire-rated sealant suits many small service penetrations: copper and steel pipes, cables and some small ducts where the tested detail allows. Other openings need collars, wraps, batts, pillows or boards. If the detail calls for something other than sealant, we say so rather than force sealant into it. Most enquiries involve seals disturbed by maintenance and left open and unsealed joints where partitions meet the slab, across service gaps in risers, linear gaps at wall heads and small duct penetrations where the tested detail allows. Searching for sealant specialists in Burray Village? Mastic Doctor has worked for contractors, FMs and building owners since 2005, CHAS accredited and a Constructionline member.
Travel to smaller places like Burray Village is planned so every penetration is sealed on one trip. Photos of the gaps, the services and the wall or floor type help us bring the right products.
Our workmanship is guaranteed for 12 months, wherever the site is. If a joint we sealed fails because of how it was installed, we come back and put it right.
- Place
- Burray Village (KW17)
- Region
- Orkney Islands
- Cover
- A 12-month guarantee
- Quotes
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
How the job changes by surface
Plastic pipes
In a fire, plastic pipework melts away and leaves an opening. Some intumescent sealants are tested on smaller plastic pipes. We check the pipe material and diameter against the detail before we start.
Masonry and concrete
Openings through concrete vary from tidy cores to rough break-outs. The gap is measured at the widest point so we know it sits within the tested range.
Service penetrations in Burray Village buildings
Island jobs, Burray Village among them, are planned around the ferry and the forecast. We need the specification and a count of penetrations before we sail. Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, with proprietary products, intumescent ones included, tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail.
Buildings near Burray Village get the fire-rated product that’s specified, installed to its tested detail. In a hotel such as The Sands Hotel, less than half a mile to the south-east of Burray Village, new pipework or cabling through bedroom and corridor walls needs sealing with the specified product.
Burray Village is about 9 miles south of Kirkwall, in the Orkney Islands. Our applicators travel to Burray Village for work on service penetrations, handled exactly as we handle every other area. 51 places across the Orkney Islands fall within our area, including Burray Village.
Business premises anywhere in KW17 are within our area. For a building on Lairds Road, Upper Waston Road and Sunfield or nearby, we can quote for service penetrations. Sites close to Burray Village are covered too, including Grimness (1 mile south), St Margaret's Hope (2 miles south-west), St Mary's (4 miles north), Widewall (4 miles south-west) and Upper Sanday (6 miles north-east). As one of the bigger centres in the Orkney Islands, Burray Village has a broad mix of commercial, public and industrial buildings. For island and remote sites, we plan travel and materials carefully.
What’s near Burray Village
Nearby you will also find W Hourston Blacksmiths Museum (2.1 miles south-west). Open spaces near Burray Village include Echna Loch and Ward Hill.
Why act early in Burray Village
Open penetrations multiply: each new service adds to the list. A schedule that is dealt with regularly stays manageable, rather than turning into a full building survey and reseal. Buildings that aren’t in daily use, such as halls and seasonal premises, may let water in unnoticed, so a failed joint has time to cause damage. Early resealing prevents it.
The price depends on how many linear metres there are, how much old material needs removing and how the joints are reached. Call for a quote when you are ready.
What you get with us
- Constructionline member
- Fully insured, including public liability cover
- A fixed quote before work starts
- 12-month guarantee on workmanship
Read our cost guide and how we’re accredited.
Places near Burray Village
What else we do in Burray Village
Diagnose, treat, sign off
We begin with a short walk round with whoever looks after the building, to confirm the scope, the order of work and any areas we must keep clear. After that, any old or failed material is removed, each joint is prepared and the new sealant goes in. For work around Burray Village, we aim for one trip, so photos, sizes and a full list matter. Outside work also needs a suitable weather window.
- The specification and schedule come first, so we know which details apply.
- Access, permits and the order of areas are agreed with the site team.
- We compare every service penetration with its tested detail before sealing.
- Foam, ordinary sealant and debris come out first.
- Backing and fire-rated sealant are installed to the detail and tooled.
- We tell you about openings that need a different product.
What we need from you
- Make sure the joints can be reached
- Flag any permit to work we will need
- For older buildings, check the asbestos register before work
Quotes
A good quote starts with a clear picture: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we’ll fill any gaps with a visit.
Related advice
After the work
For the best life from the joints:
- Ask the designer to confirm details early on refits
- Don’t let anyone top up a fire seal with the wrong product
- Record which product was used where
- Have penetrations checked while they can still be seen
Give the sealant its full cure time before ceilings, boxing or decoration go over it. Not every fire-rated product can be painted, and the data sheet says which.
Looking at service areas on a regular cycle pays off. Catching a damaged seal early keeps the fix small compared with dozens found at once.
Owners, agents and contractors
CHAS accredited and a Constructionline member, we make supplier vetting simple. Our insurance certificate can be sent along with the quote.
FMs need a contractor who is easy to get on site. Let us know the documents you need (RAMS, insurance certificate, CSCS details) and we will confirm them with the quote.
When something else is needed
Being straight saves everyone time. Fresh joints won’t solve:
- Large openings beyond what any sealant detail covers
- Construction that lacks the fire resistance the seal relies on
- Designing or specifying fire stopping, which sits with the designer or fire engineer
If you’re not sure, just call the office on 01277 525 020 or email the details over and we’ll give you a straight answer.
Joints and surfaces we work on
- Pipe penetrations
- Joints between fire-resisting walls and floors
- Cable penetrations
- Small duct penetrations where the tested detail allows
- Linear gaps at wall heads
- Service gaps in risers
Questions we are asked in Burray Village
Do you work on the island where Burray Village is?
Yes, Burray Village is within the area we cover. Every Scottish council area is within our area. We group island work where we can and plan around the crossings.
What do Scotland’s building standards say about service penetrations in Burray Village?
Scotland’s non-domestic Technical Handbook covers it in clause 2.1.14: penetrations keep at least the element’s fire resistance duration, with products tested for their end use. We install what has been specified, to the manufacturer’s tested detail, while design and approval sit with the designer and the verifier.
Do you seal on top of existing sealant?
No. Sealing over old material is one of the classic causes of early joint failure, so it all comes out first.
What if there’s asbestos in the old mastic?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and work stops until any suspect material has been tested. Removing asbestos is a job for asbestos specialists, not us.
Can you handle several sites?
Yes. Several buildings can share a single quote, and you deal with one contact throughout across South East England, Greater London and Scotland.
Can the sealant be colour-matched?
Often, yes. Many products come in a range of standard colours, and matching to RAL references or surrounding finishes is often possible. We confirm what’s available for the specified product when we quote.
Who decides which product is used?
The specification comes first, if there is one. Without one, the joint decides: how much it moves, what it bonds to and whether it’s wet, trafficked or fire-rated.