Bridge of Tilt fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Bridge of Tilt and nearby, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Openings left by services added after handover
- Penetration schedules that need working through
- Seals that don’t match their tested detail
Need fire stopping in Bridge of Tilt?
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Bridge of Tilt: questions and answers
Which Scottish guidance covers penetration seals in Bridge of Tilt?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. We install what has been specified, to the manufacturer’s tested detail, while design and approval sit with the designer and the verifier.
Is a smaller place like Bridge of Tilt outside your area?
Not at all. Bridge of Tilt is within our area. Every Scottish council area is within our area. Good photographs up front let us bring everything on the first visit.
How much does the work cost?
It depends on the job: quantities, access, the product and any phasing. Call for a fixed quote.
Is the work guaranteed?
Yes. Workmanship is guaranteed for 12 months on every job.
How do you deal with asbestos in old sealant?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and if asbestos is suspected, work stops until it’s tested. We don’t remove asbestos-containing materials.
How long will the new sealant last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Sealant joints are maintenance items, so inspect them regularly.
Can staff carry on working while you are here?
Yes, with some planning. We agree a sequence with your contact so just one area at a time is disrupted.
Fire stopping in Bridge of Tilt
Opened ceilings and riser doors often reveal service openings nobody sealed. If a specification already covers those walls and floors, we can reseal to it. Where there isn’t one, the designer or fire engineer needs to set one first. If you have unsealed penetrations discovered above suspended ceilings and improvised or mixed-product fire seals, we can put it right. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Bridge of Tilt it comes down to the same thing: failed joints cut out, faces prepared and the right sealant laid to the right depth.
For a building near Bridge of Tilt, we plan fire-rated sealing so it’s finished in one visit where possible. Photos of the gaps, the services and the wall or floor type help us bring the right products.
The 12-month guarantee covers our workmanship: preparation, application and finish. Damage, later alterations by others and movement beyond what the joint was designed for sit outside it.
- Location
- Bridge of Tilt (PH18)
- Region
- Perth and Kinross
- Cover
- 12 months on our workmanship
- Quote
- A fixed quote before we start
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Places near Bridge of Tilt
More services for Bridge of Tilt
After the work
Sealant joints are maintenance items, and how long they last depends on how they’re treated. We suggest:
- Treat an open penetration as a priority repair
- Keep general-purpose fillers away from compartment walls
- Ask which product is in place before decorating
- Look above ceilings when tiles are lifted for other jobs
Allow the manufacturer’s stated cure time before boxing in or decorating. Some fire-rated sealants accept paint and some don’t.
Specify fire stopping early on refits, not as an afterthought. The designer can then choose details that suit the services planned.
Doing it in-house
For a quick touch-up, site staff may be fine, but anything bigger is another matter: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
Some joints are best left to specialists: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. A poor seal in places like these tends to cost more to put right later.
Different surfaces, different methods
Cables and cable bundles
Single cables and small bundles are often within a fire-rated sealant’s tested detail. The detail limits bundle size and the gaps between and around cables.
Plastic pipes
In a fire, plastic pipework melts away and leaves an opening. Small sizes are sometimes covered by an intumescent sealant detail, though larger ones typically call for a collar or wrap. We confirm material and size first and tell you if sealant isn’t the right product.
Fire-rated sealing for Bridge of Tilt buildings
Scotland has its own building standards: the non-domestic Technical Handbook (clause 2.1.14) says service penetrations should be fire stopped to at least the fire resistance duration of the wall or floor, with proprietary products, intumescent ones included, tested for their end use. Our part is installing the specified fire-rated sealant to its tested detail. There are several hotels within about 2 miles of Bridge of Tilt. A hotel refit often runs new services through compartment walls between bedrooms and corridors, and each opening needs the specified seal.
Hotels such as Bridge of Tilt Hotel (to the south of Bridge of Tilt) rely on fire-resisting walls between bedrooms and corridors, and refits that add services leave penetrations to seal where fire-rated sealant is specified. For a building such as Church, new heating or data runs are the usual reason penetrations need sealing.
Bridge of Tilt is about 23 miles north-west of Blairgowrie and Rattray, in Perth and Kinross. Looking for fire stopping in Bridge of Tilt? We can help. 114 places across Perth and Kinross fall within our area, including Bridge of Tilt. Sites around Dundee have their own page, about 39 miles away.
Commercial sites across PH18 are covered. We cover commercial and managed buildings on The Lane, Invertilt Road and Wade's Bridge Road. We also cover Blair Atholl (1 mile south), Old Blair (1 mile west), Old Struan (4 miles west), Moulin (6 miles south-east) and Pitlochry (6 miles south-east) for service penetrations. Where a site is remote or on an island, we plan travel and materials carefully, so the full address helps from the start.
Local landmarks in Bridge of Tilt
Bridge of Tilt’s nearest station is Blair Atholl station, roughly 0.5 miles south-west. Other landmarks nearby include Atholl Country Life Museum (0.5 miles south-west) and Blair Castle (0.7 miles west). Not far away are Creag Odhar and Loch Moraig.
When something else is needed
We check first that sealant really is the fix. It isn’t the answer for:
- Writing the fire-stopping specification
- Fire doors, dampers or other fire safety equipment
- Approving the work on behalf of building control
Not sure which it is? You can give us a call on 01277 525 020 or email us and we’ll tell you honestly.
Where we work in Bridge of Tilt
- Service gaps in risers
- Linear gaps at wall heads
- Cable penetrations
- Pipe penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
What affects the price in Bridge of Tilt
There’s no standard rate for sealant work, because every site is different. What we look at:
- Location, for remote and island sites
- Site requirements such as inductions and permits
- Any access equipment needed
- Whether the work must be split into stages
Access often affects the price as much as the sealing: joints within easy reach take less time than ones that need access equipment. Tell us how the joints are reached and call for a quote.
What to include in your enquiry
To price the job accurately, we need to understand the site. Send us:
- Access details, including height
- Your programme or deadline
- Where the site is, with the postcode
- Specification clauses that apply
Send details, get a quote, we seal, guaranteed: that’s how every job runs. To take the first step, call 01277 525 020 or email drawings and photos.
On site: what to expect
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. On site, the work typically takes anything from one day to a planned run of visits, depending on the number of seals and the access, and our waste is bagged and taken away as we go. Where we can, we combine work around Bridge of Tilt with other jobs nearby, to make the most of each trip. Tell us how flexible your dates are.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Where the detail needs backing, it goes in at the stated depth.
- We gun the sealant in to the specified depth around each service and tool it.
- Completed areas are checked with you, with the records agreed when we quoted.
Before we start on site
- Point out parking and an unloading spot
- Share your working hours and any access restrictions
- Confirm the product named in the specification
Request a quote
To get a fixed quote, ring 01277 525 020 or send photos by email with the site address and an outline of the work. Our quote form is another easy route.