Fire stopping in Bellfields
Looking for fire stopping in Bellfields? It’s simple: send details, get a quote, we seal, guaranteed.
- Unsealed openings around new pipes and cables
- Fire-stopping items raised at inspection or handover
- Open linear gaps along the top of fire-resisting walls
Fire stopping in Bellfields
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Fire stopping in Bellfields, done properly
The test standards are BS EN 1366-3 for penetration seals and BS EN 1366-4 for linear joints, with results classified under BS EN 13501-2. A rating such as EI 60 only holds when the product is installed as it was tested. Reproducing the tested arrangement on site is the part we take care of. If you have improvised or mixed-product fire seals and open linear gaps along the top of fire-resisting walls, we can help, on cable penetrations, linear gaps at wall heads and pipe penetrations alike. Facilities teams, main contractors and managing agents in Bellfields tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
Converted and extended buildings around places like Bellfields can mix old and new construction, so it’s worth confirming the wall or floor type before choosing the seal. The right product depends on the wall or floor and the services passing through, and we’ll tell you if the detail calls for something other than sealant.
Guaranteed is the last step of every job. You get a 12-month guarantee on our workmanship, and we explain exactly what that covers when we quote.
- Place
- Bellfields (GU1, GU2, GU3)
- Region
- Surrey
- Guarantee
- A 12-month guarantee
- Quote
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Compartments and services around Bellfields
Bellfields is about 27 miles from central London. Offices around the capital are refitted often, and the cabling that follows can breach fire-resisting walls. The area within 2 miles of Bellfields holds a good number of hotels. In hotels, bedroom and corridor walls are typically fire-resisting, so services added in a refit need sealing with the specified product.
On a hospital site such as Farnham Road Hospital, which lies south of Bellfields, fire-rated sealant goes in where the specification calls for it, with the work planned around the estates team’s permits. Residences at universities like University of Surrey - Stag Hill Campus (to the south-west of Bellfields) have compartment walls that must be resealed whenever services change.
Bellfields is about 1 mile north of Guildford, in Surrey. Looking for fire stopping in Bellfields? We can help. Our Surrey coverage takes in 379 places, from busy centres to rural villages. For work in that direction, see our Reading page.
Business premises anywhere in GU1, GU2 and GU3 are within our area for service penetrations. Buildings on Lock Road, Manor Road and South Road are within our area for service penetrations. Access to Bellfields is via the A3 and A320, so getting applicators and materials to site is simple. Close to Bellfields, our area also takes in Guildford (1 mile south), Stoughton (1 mile west), Jacobs Well (1 mile north-east), Westborough (1 mile south-west) and Abbotswood (1 mile south-east). Nearby towns on our patch include Woking (4 miles north), Camberley (8 miles north-west), Epsom (15 miles north-east), Farnham (10 miles west), Egham (12 miles north) and Walton-on-Thames (12 miles north-east).
What’s near Bellfields
Locally, jobs take us to sites close to Weyfield Academy, Christ's College and Riverside Park and the streets around them. The nearest railway station is London Road (Guildford) station, roughly 1.2 miles south-east of the centre. Nearby you’ll also find Guildford Castle (1.5 miles south) and Guildford Cathedral Treasury (1.1 miles south-west). Green spaces nearby include Pewley Hill and Pewley Down.
Different surfaces, different methods
Drylining partitions
Service holes through plasterboard are frequently oversized or ragged. An oversized hole may be outside the sealant’s range, and the detail may call for board patching or another product.
Linear joints
Head-of-wall gaps, slab edges and wall junctions are linear joints. BS EN 1366-4 testing sets the joint widths, depths, backing and movement a seal covers.
Signs you need fire stopping in Bellfields
Head-of-wall joints and wall-to-wall junctions are frequent weak points. Movement in the frame or slab can open the joint. Linear joint details set a width range and movement capability, and the seal has to sit within them.
It’s worth sending us details if you spot any of the following:
- Seals that don’t match their tested detail
- Non-fire-rated filler around services
- Fire-rated sealant that has cracked or shrunk back
- Openings found when ceilings come down for a refit
Hotels like The Stoke Hotel (to the south of Bellfields) are refurbished in phases, and each phase can open up compartment walls.
What to look for in a quote
- Their approach to joint depth and backing
- How the joint faces will be prepared and primed
- Will CSCS-carded applicators be on site?
- What the guarantee covers, and for how long
Questions we are asked in Bellfields
Do you cover business parks and estates near Bellfields, such as Ladymead Retail Park?
Yes. We cover Bellfields and the area around it, including industrial estates, business parks and retail parks such as Ladymead Retail Park. Send details of the unit and the work through our quote form for a quick quote.
Do you take on work at healthcare sites like Farnham Road Hospital?
Yes, healthcare and care buildings are part of our work. Before anything starts, the estates team agrees permits, inductions and infection-control measures with us.
Do you seal openings left by new services?
Yes, provided a specification covers them. Openings left by new services are among the most common jobs we see and we close them with the specified product.
What do BS EN 1366-3 and BS EN 13501-2 mean?
The tests are BS EN 1366-3 for penetrations and BS EN 1366-4 for linear joints, and classification is to BS EN 13501-2. An EI 60 seal kept its integrity and insulation for 60 minutes as tested.
Do you design or specify fire stopping?
No. Deciding what is needed sits with the designer, fire engineer and building control. Our role is installing what they specify, to the product’s tested detail.
Is fire stopping in Scotland covered by different guidance?
Our area runs from Greater London and the South East to every part of Scotland. In Scotland, clause 2.1.14 of the non-domestic Technical Handbook says service penetrations should keep at least the fire resistance of the wall or floor, using products tested for their end use.
Can you quote from photos?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we will arrange a visit.
Cost factors for service penetrations
Each job is priced on its own details. The things that drive the figure:
- Location, for remote and island sites
- The total length or number of joints
- Access and working height
- Working within restricted access windows
Every site prices differently: the joint sizes, the specified product, access and working hours each have a bearing. Send the details and a fixed figure follows.
What to include in your enquiry
Good information means a firmer quote. When you get in touch, include:
- Whether the building will be occupied during the work
- Any specification or named product
- Whether an asbestos survey exists
- When you need the work done
Send details, get a quote, we seal, guaranteed: that’s how every job runs. To take the first step, ring 01277 525 020 or email drawings and photos.
From enquiry to sign-off
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Joint faces are cleaned back to sound, dry surfaces, the manufacturer’s primer is applied where it’s called for, and each bead is tooled to a neat concave finish. What matters most for a job in Bellfields is a clear list of what needs doing, so send photos of each area. A fixed quote follows.
- First we go through the drawings, schedule or specification for the seals and ask about anything unclear.
- On site, each opening is checked against the tested detail it is meant to follow.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- We fit the backing the detail asks for, to the stated depth.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
What we need from you
- Let us know about inductions and permits
- Send your site hours and access windows
- Send asbestos survey details if the building is pre-2000
Get a fixed quote
Specifications, drawings and tender packages are welcome with any enquiry, and we’ll price the work to it. For smaller jobs, photographs and a description will do.
Related advice
What we can’t put right
Some faults sit outside our scope, and we point that out rather than sealing over them:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Openings that need collars, wraps, batts or boards rather than sealant
- Gaps in walls that were never built as compartment walls
If you are not sure, just call 01277 525 020 or send details through our quote form and we will give you a straight answer before you book.
Joints and surfaces we work on
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Service gaps in risers
- Pipe penetrations
- Linear gaps at wall heads
- Cable penetrations
Aftercare for building managers
Keep the joints in good shape with a few simple steps:
- Flag new cables with no seal around them
- Keep general-purpose fillers away from compartment walls
- Get seals inspected before ceilings and boxing close
- File the specified details where the next contractor can find them
Allow the manufacturer’s stated cure time before boxing in or decorating. Not every fire-rated product can be painted.
Specify fire stopping early on refits, not as an afterthought. The designer can then choose details that suit the services planned, and the work runs in step with the M&E.