Fire Stopping in Aberfeldy
Looking for fire stopping in Aberfeldy? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Snag lists that include open service penetrations
- Head-of-wall gaps with no fire seal
- Seals that don’t match their tested detail
Fire stopping in Aberfeldy
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
About our fire stopping in Aberfeldy
It helps to set out our role at the start. Deciding the specification sits with the designer, the fire engineer and building control; sign-off sits with them too. What we bring is careful installation of the specified sealant, to the maker’s guidance. Most enquiries involve fire seals cut back for extra cables and never reinstated and open linear gaps along the top of fire-resisting walls, on linear gaps at wall heads, joints between fire-resisting walls and floors and pipe penetrations. Facilities teams, main contractors and managing agents in Aberfeldy tend to want the same three things: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
Travel to smaller places like Aberfeldy is planned so every penetration is sealed on one trip. Send the specification and photos of the openings, with sizes if you have them.
The 12-month guarantee is for workmanship rather than wear and tear. Sealant wears with time, and movement, weather, cleaning and use decide how fast, so we are clear about what is covered before work starts.
- Place
- Aberfeldy (PH15)
- Wider area
- Perth and Kinross
- Guarantee
- 12 months on every job
- Quote
- A fixed quote before we start
- Call
- 01277 525 020
- Updated
- 3 November 2026
Our process
A typical day starts with protection: masking tape along the joint edges and sheeting over anything nearby. On site, the work typically takes anything from one day to a planned run of visits, depending on the number of seals and the access, and we clear our waste as we work. For work around Aberfeldy, we aim for one trip, which is why we ask for photographs and a full list first. External joints need a dry spell as well.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Unsuitable material is removed and the opening cleaned first.
- Backing and fire-rated sealant are installed to the detail and tooled.
- Anything outside the detail is reported to you rather than sealed.
What we need from you
- Send any specification or drawings in advance
- Send asbestos survey details if the building is pre-2000
- Tell us what induction or permit system the site runs
Quotes
Every quote starts with the facts: the joints involved, quantities, access and the product called for. Share whatever details you have and we’ll fill any gaps with a visit.
Related advice
Quoting for work in Aberfeldy
Before we quote, we look at:
- Removal of failed or old sealant
- The size and state of each joint
- Whether the work must be split into stages
- How accessible the joints are
The work involved drives the cost: stripping out, preparation, sealing, access and phasing. Call for a quote.
Sending details for a quote
There’s no need for a formal survey. A few details are enough to get going:
- Drawings or a marked-up plan, if available
- A wide shot and a close-up of the area
- Your programme or deadline
- What the building is and how it’s used
To get a fixed quote, give us a call on 01277 525 020 or email us with the site address and an outline of the work. Our quote form is another easy route.
Building owners, agents and FMs in Aberfeldy
Facilities managers want contractors who arrive with the paperwork sorted. Let us know the documents you need (RAMS, insurance certificate, CSCS details) and we will confirm them with the quote.
Main contractors use us as their sealant subcontractor, on new build and refurbishment alike. Programme, specification and site rules come first.
Signs you need fire stopping in Aberfeldy
Mixing products or improvising a detail breaks the link with the test evidence. An oversized gap, too shallow a bead, missing backing or two makers’ products combined are the usual culprits.
Site and facilities staff are often the first to spot these:
- Service penetrations left open after M&E works
- Hidden openings found during inspections
- Old intumescent sealant that has split away
- Open linear gaps along the top of fire-resisting walls
Schools such as Breadalbane Academy often have new data and services installed during holidays, and penetrations through fire-resisting walls should be checked afterwards.
Questions to ask before you book
- Their approach to joint depth and backing
- Will failed sealant be removed rather than covered?
- How the joint faces will be prepared and primed
- Their public liability cover
Should maintenance staff do it?
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and our CSCS-carded applicators are used to working under those rules.
Fire stopping around Aberfeldy: points for this area
Scottish guidance (non-domestic Technical Handbook, clause 2.1.14) asks that penetrations match at least the fire resistance period of the element they pass through, using products tested for the way they’re used. We install fire-rated sealant to that tested detail where it is specified. A 2-mile radius around Aberfeldy takes in plenty of hotels. Bedroom-to-corridor walls in hotels are normally fire-resisting, so new cabling or pipework through them has to be sealed to the tested detail.
In a hotel such as Breadalbane Arms Hotel (less than half a mile south of Aberfeldy), new pipework or cabling through bedroom and corridor walls needs sealing with the specified product. For a unit at a site such as Aberfeldy Industrial Estate, less than half a mile north-east of Aberfeldy, new power or data runs between office and warehouse can breach a compartment wall.
Aberfeldy is about 20 miles west of Blairgowrie and Rattray, in Perth and Kinross. Businesses, contractors and managing agents in Aberfeldy use us for work on service penetrations. We work across 114 places in Perth and Kinross, from busy centres to rural villages. Sites around Dundee have their own page, about 35 miles away.
We cover the PH15 postcode districts. If your site is on Market Street, Burnside Lane and Burnside or close by, send details and we will quote for service penetrations. With the A826 and A827 nearby, Aberfeldy is easy to get to with materials and equipment. Sites close to Aberfeldy are covered too, including Little Ballinluig (4 miles north-east), Grandtully (4 miles north-east), Kenmore (6 miles south-west), Acharn (7 miles south-west) and Port na Craig (7 miles north-east).
Near you in Aberfeldy
In Aberfeldy, that means premises near Library and Area Office, Weem Hotel and Tay Forest Park, among other places. A little further out are Weem Castle (0.9 miles north-west). Not far away are Farragon Hill and Loch Glassie.
What happens if it’s left?
A seal that doesn’t match its tested detail gives false comfort. Correcting it means cutting it out and starting again with the specified product, and doing it once, properly, is cheaper. Renewing every failing joint on one visit is the sensible approach for a place like Aberfeldy. Photos of each area help us quote the whole job.
Small jobs and large programmes are priced from the same things: scope, access, product and programme. Call for a quote and we’ll put a fixed figure on it.
Why appoint us
- Products installed to the manufacturer’s instructions
- 12-month guarantee on workmanship
- Health and safety: CHAS accredited
- Work carried out by CSCS-carded applicators
Read our cost guide and our accreditations.
Aberfeldy: questions and answers
What do Scotland’s building standards say about service penetrations in Aberfeldy?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
Is Aberfeldy too small for you to travel to?
Not at all: smaller places are covered as well as towns. Every Scottish council area is within our area. Send photos and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
How soon can the area be used again?
Curing time varies by product, and we confirm it on the day, and flag anything to keep off until it has cured.
Can you handle several sites?
Yes. We take on portfolio and planned maintenance work, with each site phased to suit its occupants.
How long does a typical visit take?
That varies with the scale of the job, but the work normally takes a single visit for a short list of penetrations, or a phased programme for a whole building. Larger or phased jobs take longer, and we’ll give you a timescale with the quote.
What’s the quickest route to a quote?
There are four steps: send details, get a quote, we seal, guaranteed. The first step only needs photographs and a postcode.
Are your applicators CSCS-carded?
Yes. If you need card details for site access, tell us and we will confirm them with the quote.