Expansion and movement joint sealing in Scalasaig, Argyll and Bute
Work needed on a movement joint in Scalasaig? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Damp inside where a wall movement joint has failed
- Car park joints leaking onto vehicles below
- Layers of sealant in a movement joint
Expansion joint sealing in Scalasaig
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How we handle expansion joint sealing in Scalasaig
Few joints take as much punishment as those in a car park. Wheel loads, grit and de-icing salts attack the seal and the concrete either side, so failed seals soon lead to leaks onto the level below and broken edges. We reseal deck and ramp joints with a trafficable sealant chosen for the movement, phasing bays so the car park can stay in use. We work on blockwork control joints, brickwork movement joints and car park decks and ramps, and what we’re called in for most is sealant peeling off one face of the joint and arrises breaking up along floor joints. A single leaking joint is often how a building in Scalasaig first comes to us: we look at the rest while we are there and tell you what we find.
In smaller places such as Scalasaig, the joints we’re asked about sit in workshops, farm sheds, schools and halls. Concrete slabs and yards there take vehicles and weather.
A 12-month guarantee applies to all our work. Should something we installed fail, call 01277 525 020 or email a schedule or drawings and we will come back to it.
- Place
- Scalasaig (PA61)
- Region
- Argyll and Bute
- Cover
- A 12-month guarantee
- Quote
- A fixed quote before we start
- Call
- 01277 525 020
- Last updated
- 3 November 2026
What we can’t put right
Before quoting, we check that sealant is the right answer. It isn’t the answer for:
- Mechanical expansion joint covers, cover plates or proprietary joint systems (a specialist supplier’s job)
- Crumbling edges that would give a new bead nothing sound to grip
- Cracking or settlement that calls for an engineer’s assessment
Not sure which it is? You can speak to us on 01277 525 020 or send photos by email and we will tell you honestly before you book.
Where we work in Scalasaig
- Car park decks and ramps
- Blockwork control joints
- Precast concrete panel joints
- Cladding panel joints
- Podiums and floor movement joints
- Brickwork movement joints
Different surfaces, different methods
Internal floor movement joints
Warehouse and retail floors have saw-cut induced joints and construction joints. A semi-rigid filler is common in trafficked industrial floors, with a flexible sealant where movement is larger.
Joints between different materials
Junctions between brick and render, or concrete and cladding, move independently. The product must bond to both substrates and cope with the movement, with primer where specified.
Why act early in Scalasaig
Leaving a failed movement joint rarely stays a small problem. Grit and water fill the gap and the material either side breaks up and the job grows to repairs as well as sealing. Acting at the first split keeps the cost down. Exposed buildings in Scotland take a lot of weather, so it’s worth renewing joints around Scalasaig before they leak.
The work involved drives the cost: stripping out, preparation, sealing, access and phasing. Call for a quote and we’ll explain how it’s made up.
Why choose Mastic Doctor in Scalasaig
- CSCS-carded applicators
- Health and safety: CHAS accredited
- Failed material removed, not covered up
- Standard and matched colours in many product ranges
Warehouse floors and decks around Scalasaig
The sea is no more than about 1 mile from Scalasaig. Open joints in coastal car parks and yards let in salt-laden water as well as grit, so a failed joint lets more in and the edges break up sooner. Being in the west of Scotland, Scalasaig gets more rain than eastern areas. Open joints in external slabs take a lot of water. External sealing is booked for dry spells, with some give in the dates.
For floors and slabs around Scalasaig, the product is chosen for the traffic and the movement at each joint. Once a joint near Scalasaig opens up, grit and water get in and the edges start to break; we’ll tell you if the edges need repairing first.
Scalasaig is in Argyll and Bute. Businesses, contractors and managing agents in Scalasaig use us for work on movement joints. Scalasaig is one of 124 places we cover in Argyll and Bute for movement joints. We also cover Glasgow, around 76 miles from Scalasaig.
Work on movement joints is covered throughout PA61. Streets here include Dunoran and An Faire Mor, and sites on any of them can send details for a fixed quote. Close to Scalasaig, our area also takes in Upper Kilchattan (1 mile north-west), Bunnahabhain (13 miles south), Port Askaig (16 miles south), Keills (16 miles south) and Bunessan (17 miles north). Where a site is remote or on an island, travel and materials need planning ahead, so the full address helps from the start.
Local landmarks in Scalasaig
In Scalasaig, that means premises near Colonsay Inn. A little further out are The Old Waiting Room (less than half a mile west). Green spaces nearby include Loch Fada and Càrnan Eoin.
Diagnose, treat, sign off
Site rules come first: signing in, inductions and any permit to work. With the paperwork done, we take the joints in the sequence agreed with you, and each area is checked before we leave it. For a building near Scalasaig, directions, keys and a contact on the day are worth sorting early. That goes into the plan alongside the quote.
- We assess the joints on site or from photos, noting widths and how each has failed.
- You receive a fixed quote stating the product and the movement it is rated for.
- Phasing is agreed so decks, floors or entrances can stay in use where needed.
- We strip the old sealant or filler and prepare each face until it’s sound and dry.
- Backing rod or bond-breaker sets the depth, primer goes on where specified, and the sealant is applied and tooled.
- We check each joint with you, confirm the cure time and sign off under our 12-month guarantee.
Getting the site ready
- Send asbestos survey details if the building is pre-2000
- Clear stock, furniture or equipment away from the joints
- Explain the parking and delivery arrangements
Request a quote
Every job follows the same four steps: send details, get a quote, we seal, guaranteed. The first step is to give us a call on 01277 525 020 or send details through our quote form with what you know.
Advice
What sets the cost
There’s no standard rate for sealant work, since sites vary so much. What we look at:
- Working within restricted access windows
- How much there is to seal
- Specialist products, such as fire-rated or hygienic sealants
- Access and working height
There’s no price list, because the scope varies so much from one building to the next. Call for a quote and we will price your job on its own details.
Details that help us quote
We can often quote from photos and a few details. Please tell us:
- The type of building and who uses it
- Rough lengths or quantities, or drawings if you have them
- Where the site is, with the postcode
- Photos of the joints, close up and from further back
Every quote starts with the facts: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we’ll fill any gaps with a visit.
Doing it in-house
Certain joints really need a specialist: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. A poor seal in places like these tends to cost more to put right later.
Paperwork matters too. Many sites expect CSCS cards, RAMS and proof of insurance, and we’ll confirm the paperwork you need with the quote.
Scalasaig: questions and answers
Do we have to stop operations in Scalasaig while the joints are sealed?
Rarely. Work is phased around your operations. Tell us which hours and entrances we can use and we will plan from there.
Is Scalasaig off your patch?
Not at all: smaller places are covered as well as towns. We work across every Scottish council area. Send photos and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
Do the joint edges need to be sound before sealing?
Broken arrises have to be put right before resealing and we’ll flag every length affected. Sealing over them leads to early failure.
Does the weather affect the work?
It can, for external work. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so we watch the forecast and rearrange outside work if we have to. Indoors, the weather is rarely a problem.
Do you take on small jobs?
We quote for single jobs as well as large packages and programmes. Send details for a fixed quote.
Are expansion joints and movement joints the same thing?
The terms overlap a great deal. Both let materials grow and shrink with temperature, moisture and load while the sealant stops grit and water getting in.
Who decides which product is used?
Where there’s a specification, we use the product it names. Otherwise, we recommend a product to suit the joint’s movement, the substrate and the conditions, following the manufacturer’s guidance.