Expansion and movement joint sealing in Chipping Ongar, Essex
Expansion joint sealing for Chipping Ongar, from a contractor working since 2005. Fully insured, with a 12-month guarantee.
- Weathered movement joint sealant that no longer flexes
- Expansion joints split through the centre of the bead
- Water getting into the wall through a failed joint
Expansion joint sealing for businesses in Chipping Ongar
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
How a job runs
When we get to site, we sign in, go through any site induction and check how permits are handled. Floors, finishes and fittings next to the joints are covered before any cutting starts, and the work usually takes a short visit for a handful of joints, or several days or more for a car park deck or long runs of facade joints. If neighbouring businesses or buildings around Chipping Ongar need work too, visits can be combined. Tell us your site hours and we will plan around them.
- First the joints are inspected, widths measured and the type of failure noted.
- You receive a fixed quote stating the product and the movement it is rated for.
- Phasing is agreed so decks, floors or entrances can stay in use where needed.
- The failed seal is cut out and both joint faces cleaned back to sound material.
- Depth is controlled with backing, the faces are primed where the maker calls for it, then the bead is laid and tooled.
- Finished joints are inspected, the cure time confirmed and the 12-month guarantee applies.
Preparing the site
- Send any specification or drawings in advance
- Tell us your opening times and when work is allowed
- Point out parking and an unloading spot
Ask for a quote
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To ask for one, phone 01277 525 020 or email us.
Read more
Expansion joint sealing in Chipping Ongar
Floor movement joints in warehouses, retail and public buildings carry wheeled traffic. Unsupported edges break up under wheels. We’ll tell you if the edges need repairing before sealing, and phased work keeps areas in use. We work on blockwork control joints, podiums and floor movement joints and cladding panel joints, and what we’re called in for most is water getting into the wall through a failed joint and sealant peeling off one face of the joint. Whoever orders the work in Chipping Ongar, the brief is normally the same: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
Rural business units around smaller places such as Chipping Ongar often have new slabs laid inside older buildings. Joints in those slabs need a product suited to whatever runs over them, from pallet trucks to foot traffic.
Guaranteed is the last step of every job. You get a 12-month guarantee on our workmanship, and we explain exactly what that covers when we quote.
- Location
- Chipping Ongar (CM5)
- Region
- Essex
- Guarantee
- 12 months on every job
- Price
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Expansion joint sealing in Chipping Ongar: the local picture
Chipping Ongar is about 20 miles from central London. The roads out of London are lined with trade parks and distribution sheds, and their floor joints take forklift and pallet-truck traffic all day. Chipping Ongar sits in one of the drier corners of the country, the South East. Outside joints in yards and car parks still have to be dry before sealing, while winter salting gets into any joint left open.
If you manage units on an estate such as Hallsford Bridge Industrial Estate, which lies south-east of Chipping Ongar, the floor joints under forklifts and pallet trucks and the slab joints in the yard are the ones to watch. In a school such as Chipping Ongar Primary School, movement joints in brick, block and hall floors tend to be forgotten until they leak. Sites like St. Margaret's Hospital (to the west of Chipping Ongar) carry ambulances, deliveries and visitors’ cars over their road and deck joints.
Chipping Ongar is about 6 miles north-west of Brentwood, in Essex. We send applicators to Chipping Ongar for movement joints, handled exactly as we handle every other area. We work across 644 places in Essex, from busy centres to rural villages. Our London page has more on work in that area, about 20 miles away.
Commercial sites across CM5 are covered for movement joints. Among the streets we cover are High Street, Lavender Mews and Stanley Place. Chipping Ongar sits on or close to the A128, useful when we plan access and materials. If your building is just outside Chipping Ongar, we cover Greensted (1 mile west), Shelley (1 mile north), High Ongar (1 mile east), Greensted Green (2 miles west) and Norton Mandeville (2 miles north-east). Further afield, our area takes in Chelmsford (11 miles east), Basildon (13 miles south-east), Harlow (7 miles north-west), Brentwood (6 miles south-east), Billericay (9 miles south-east) and Loughton (9 miles south-west).
Landmarks near Chipping Ongar
In Chipping Ongar, that means premises near The Ongar Academy and The Royal Oak pub and the streets around them. Other landmarks nearby include Willingale Doe (4.5 miles north-east) and St. Margaret's Hospital (5.2 miles west). Not far away are Gernon Bushes.
When something else is needed
We check first that sealant really is the fix. It isn’t the answer for:
- Proprietary pre-formed expansion joint systems
- Failed waterproofing membranes on podiums, roofs or decks (a waterproofing specialist’s job)
- Cracking or settlement that calls for an engineer’s assessment
Not sure which it is? You can give us a call on 01277 525 020 or email the details over and we’ll tell you honestly.
Joints and surfaces we work on
- Podiums and floor movement joints
- Blockwork control joints
- Car park decks and ramps
- Precast concrete panel joints
- Brickwork movement joints
- Cladding panel joints
What happens if it’s left?
Patching the worst lengths of a joint can make sense short term. But if the rest of the run is the same age and product, it’s normally not far behind. We can price a patch and a full reseal side by side. A failed joint lets water into a building whatever its size. Early resealing avoids the damage that follows a leak.
We don’t publish prices, since every building and every scope is different. For a fixed figure, call for a quote.
Why appoint us
- CHAS accredited contractor
- Work carried out by CSCS-carded applicators
- Commercial sealant work since 2005
- Colours confirmed for the specified product
Take a look at our cost guide or how we’re accredited.
Owners, agents and contractors
Main contractors use us as their sealant subcontractor. We work to your programme, your specification and your site rules.
We take on planned maintenance as well as one-off repairs: resealing failed joints building by building, on a schedule that suits your budget. Chipping Ongar can form part of a wider programme across Essex.
Your questions answered
Is a smaller place like Chipping Ongar outside your area?
Not at all: smaller places are covered as well as towns. London and every South East county are within our area. Good photographs up front let us bring everything on the first visit.
Is Hallsford Bridge Industrial Estate, near Chipping Ongar, within your area?
Yes. Our area takes in Chipping Ongar and its surroundings, with estates and business parks such as Hallsford Bridge Industrial Estate included. Photos and a short description are enough for a first look.
Can you handle several sites?
Yes. Several buildings can share a single quote, and you deal with one contact throughout across South East England, Greater London and Scotland.
What if there’s asbestos in the old mastic?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and work stops until any suspect material has been tested. We don’t remove asbestos-containing materials.
Will you just go over the old sealant?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, since fresh sealant will not bond reliably to aged material.
Do you offer coloured sealant?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We’ll confirm the colours available for the specified product.
When can you be on site?
Give us your site hours and any access windows in your enquiry, and we’ll schedule the work to suit. Our office runs Monday to Friday, 8am until 5pm.
Looking after the joints
A few simple habits keep the new joints working:
- Treat a small split as a warning, not a cosmetic issue
- Keep traffic off new joints until the cure time is up
- Check joints after long freezing spells
- Sweep decks, ramps and floors so grit doesn’t collect in the joints
On car parks, winter clearance can damage deck joint sealant. Raising blades over joints where possible protects the seal, and it’s worth checking joints once the cold weather has passed.
An open joint fills with grit, and a joint full of grit can’t close. The arrises crack and break away under the load and the reseal becomes an edge repair as well. Keeping the seal sound avoids all of that.
How the job changes by surface
Concrete and precast panel joints
Precast panels often have surface residues that sealant won’t bond to. Proper cleaning and primer where specified give a sound bond and check the edges for soundness as we go.
Joints between different materials
Hybrid or MS polymer sealants bond to many substrates. The choice depends on the substrates and how much the joint moves.