Fire stopping in Shipton Bellinger
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Shipton Bellinger and nearby, carried out by CSCS-carded applicators. Fully insured and CHAS accredited.
- Penetration schedules that need working through
- Fire seals cut back for extra cables and never reinstated
- Openings left by services added after handover
Fire stopping in Shipton Bellinger
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Fire stopping in Shipton Bellinger, done properly
We should be clear about what we do and don’t do. Deciding the specification sits with the designer, the fire engineer and building control. What we bring is careful installation of the specified sealant, to the maker’s guidance on sites in Shipton Bellinger. We work on service gaps in risers, linear gaps at wall heads and pipe penetrations, and the failures we are asked to look at most are builders’ foam or ordinary silicone in compartment walls and damaged fire seals in risers and voids. Looking for mastic applicators who cover Shipton Bellinger? Mastic Doctor has worked for contractors, FMs and building owners since 2005, with CSCS-carded applicators.
Around smaller places like Shipton Bellinger, penetration seals come up in schools, halls, pubs with rooms, care homes and farm buildings used as offices. Any service penetration through those walls should be closed with the specified product, set out as its test evidence shows.
The 12-month guarantee covers our workmanship: the preparation, the sealing and the tooling. It doesn’t extend to damage, other trades’ later work or movement the joint was never designed to take.
- Where
- Shipton Bellinger (SP9)
- Wider area
- Hampshire
- Guarantee
- 12 months on every job
- Price
- Quoted before any work starts
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Fire stopping in Shipton Bellinger: the local picture
In England, Approved Document B covers fire stopping of openings and penetrations. References to the older BS 476 classes are being removed from it from 2 September 2029, after which the European classification, BS EN 13501-2, is the route, subject to transitional arrangements. We install whatever has been specified, to the product’s tested detail.
In a building such as Church of St Peter, any service penetration through a fire-resisting wall should be sealed to the specified detail. In a hotel such as Gray Manor Hotel (1.1 miles south of Shipton Bellinger), new pipework or cabling through bedroom and corridor walls needs sealing with the specified product.
Shipton Bellinger is in Hampshire. Our applicators travel to Shipton Bellinger for work on service penetrations. Shipton Bellinger is one of 723 places in Hampshire on our list for service penetrations. There’s a separate page for Southampton, about 23 miles away.
Work on service penetrations is covered throughout SP9, whatever the building. Buildings on High Street, Gardeners Green and Hedges Close are within our area for service penetrations. Sites close to Shipton Bellinger are covered too, including Tidworth (2 miles north), Perham Down (3 miles north-east), Kimpton (3 miles east), Great Shoddesden (4 miles north-east) and Ludgershall (4 miles north-east). A short drive away, we cover Andover (8 miles east), Whitchurch (15 miles east), East Anton (9 miles east), Picket Piece (10 miles east), Picket Twenty (10 miles east) and Finkley Down (10 miles east).
Local landmarks in Shipton Bellinger
Recent enquiries here include premises near The Boot Inn and The Wellington Academy, among other places. Shipton Bellinger’s nearest station is Grateley station, about 3.4 miles south-east of the centre. Other landmarks nearby include Ludgershall Castle (4.2 miles north-east). Green spaces nearby include Beacon Hill and Winterbourne Downs RSPB reserve.
Diagnose, treat, sign off
We follow your site rules from the start: signing in, inductions and any permit to work. Once we’re cleared to begin, the joints are worked through in the order agreed with your site contact, and each area is checked before we leave it. Smaller jobs around Shipton Bellinger can be grouped with others nearby. You will have a fixed quote before work starts.
- We read the specification, drawings or penetration schedule you send.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Unsuitable fillers and loose debris are taken out of each opening.
- Mineral wool or other backing goes in wherever the detail asks.
- We apply the specified sealant to the depth and around the services as the detail shows.
- If an opening needs something other than sealant, we tell you instead of improvising.
Getting the site ready
- Send any specification or drawings in advance
- Make sure the joints can be reached
- Explain the parking and delivery arrangements
Quotes
Send us photos, drawings or a joint schedule and a fixed quote comes back to you. Where a site visit makes more sense, we’ll arrange one.
Advice
Owners, agents and contractors
CHAS accredited and a Constructionline member, we make supplier vetting simple. Our insurance certificate can be sent along with the quote.
Blocks and communal areas make up much of the work for housing associations and agents. Work can be phased so residents and staff keep access throughout, with each stage agreed with your site contact.
When something else is needed
Our job is the joint, not everything around it. On its own, sealant can’t deal with:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Approving the work on behalf of building control
- Reviewing a building’s overall fire safety
If in doubt, ring 01277 525 020 or email us and we’ll say what we think.
Joints and surfaces we work on
- Linear gaps at wall heads
- Service gaps in risers
- Cable penetrations
- Pipe penetrations
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
Places near Shipton Bellinger
Other services in Shipton Bellinger
Site staff or a sealant specialist?
Putting right a botched joint often costs more than sealing it well at the start, since all of it has to come out and the faces be cleaned back again. That’s why many clients bring in a specialist from the beginning.
Using site staff can make sense for a small touch-up, but larger jobs are different: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
Aftercare for building managers
Your facilities or cleaning team can help the joints last. Share these points with them:
- Ask which product is in place before decorating
- Have penetrations checked while they can still be seen
- Agree the fire-stopping specification before services go in
- Report damaged or disturbed seals as soon as they’re spotted
Keep the product data and installation details with the building’s fire safety information. Anyone resealing later needs to know which product and detail were used.
Regular walk-rounds of service areas are worth the time. Catching a damaged seal early keeps the fix small.
Questions we are asked in Shipton Bellinger
What happens to BS 476 references for fire stopping in Shipton Bellinger?
Approved Document B loses its BS 476 references from 2 September 2029, and BS EN 13501-2 becomes the route, subject to transitional arrangements. Our part doesn’t change: the specified product, to its tested detail.
Do you decide the fire-stopping details for buildings in Shipton Bellinger?
No, that sits with the designer, fire engineer or building control. Our part is installing the specified product to its tested detail, and telling you if the detail calls for something other than sealant.
When can you be on site?
Give us your site hours and any access windows in your enquiry, and we will schedule the work to suit. You can reach the office between 8am and 5pm, Monday to Friday.
How do you deal with asbestos in old sealant?
The duty to manage asbestos sits with the building’s dutyholder, so we’ll ask for the register before work on an older building. Work pauses if suspect material is found, until it has been tested.
Can the building stay open while you work?
Yes, as long as we plan it. Tell us your site hours and access windows and we will plan around them.
Do you need to see the site first?
It depends on the job. Simple work can often be priced from photographs, while larger or less clear jobs get a site visit first.
Do you hold CHAS accreditation?
Yes. We are CHAS accredited and a Constructionline member.
What we’re called out for in Shipton Bellinger
Linear gaps fail where a fire-resisting wall meets a slab, soffit or another wall. Deflection and building movement can open these gaps, and a product not tested for that movement may crack. Linear joint details set a width range and movement capability, and the seal has to sit within them.
If one of these sounds familiar, it’s time for a closer look:
- Damaged fire seals in risers and voids
- Openings found when ceilings come down for a refit
- Old intumescent sealant that has split away
- Openings left by services added after handover
Schools such as Shipton Bellinger Primary School often have new data and services installed during holidays, and penetrations through fire-resisting walls should be checked afterwards.
Questions to ask before you book
- Which product they’ll use, and why it suits the joint
- What site paperwork they can supply
- How long is the guarantee, and what does it include?
- Whether their applicators hold CSCS cards