Risinghurst fire stopping
Fire-rated and intumescent sealing of service penetrations and linear gaps in Risinghurst. CHAS accredited, Constructionline member, with a 12-month guarantee on workmanship.
- Unsealed penetrations discovered above suspended ceilings
- Unsealed joints where partitions meet the slab
- Old intumescent sealant that has split away
Need fire stopping in Risinghurst?
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Doing it in-house
General builders and handymen seal joints, but it isn’t their main trade. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint, which is what makes a joint last.
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and we will confirm the paperwork you need with the quote.
Fire stopping in Risinghurst
The test standards are BS EN 1366-3 for penetration seals and BS EN 1366-4 for linear joints. A rating such as EI 60 only holds when the product is installed as it was tested. So our job is to reproduce that arrangement faithfully. If you have service penetrations left open after M&E works and non-fire-rated filler around services, we can help, on linear gaps at wall heads, pipe penetrations and cable penetrations alike. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Risinghurst it comes down to the same thing: failed joints cut out, faces prepared and the right sealant laid to the right depth.
Around Risinghurst, penetration and linear seals tend to be one-building jobs. Send the specification, drawings or photos of the openings and we’ll quote to suit.
We stand by our work with a 12-month guarantee. That covers our preparation and application, and if something we did falls short, we return to it.
- Location
- Risinghurst (OX3)
- Region
- Oxfordshire
- Guarantee
- A 12-month guarantee
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Updated
- 3 November 2026
Places near Risinghurst
More services for Risinghurst
Diagnose, treat, sign off
At the end of each section, we remove the tape, clean down and inspect every joint, ready for your sign-off. If an area should be left alone while the sealant cures, we say how long and put signs out. For a job in Risinghurst, the main thing is a clear picture of the work, so send photos of each area. You will then get a fixed price for the work.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
Preparing the site
- Point out any areas we must not close
- For older buildings, check the asbestos register before work
- Arrange parking or a loading space
Getting a fixed quote
Send details, get a quote, we seal, guaranteed: that’s how every job runs. The first step is to ring 01277 525 020 or email a schedule or drawings with what you know.
Advice
Aftercare for building managers
Keep the joints in good shape with a few simple steps:
- Settle who seals which penetrations at the start of a project
- Keep general-purpose fillers away from compartment walls
- Arrange inspection before areas are covered up
- File the specified details where the next contractor can find them
During planned inspections, look at seals in risers, cupboards and voids. Look for cracks, unsealed new cables and gaps that have been enlarged.
Regular walk-rounds of service areas are worth the time. A cracked or disturbed seal found early is a small job.
What sets the cost
What shapes the price:
- Access and working height
- Location, for remote and island sites
- Whether the work must be split into stages
- The total length or number of joints
The work involved drives the cost: stripping out, preparation, sealing, access and phasing. Call for a fixed quote and we’ll explain how it’s made up.
Sending details for a quote
However big the job, these details speed things up:
- A wide shot and a close-up of the area
- Any dates the work must fit around
- The postcode of the building
- The product your specification calls for
To get a fixed quote, ring 01277 525 020 or email a schedule or drawings, telling us the site location and the nature of the job. Our quote form is another easy route.
Risinghurst: questions and answers
Is a smaller place like Risinghurst outside your area?
No. Small places get the same service as large ones. We cover Greater London and the counties of the South East. Where we can, we group nearby jobs to make the most of each trip.
Can work in a care setting near Risinghurst go ahead while residents are there?
Yes. We work around residents’ routines, a room or two at a time. We follow the home’s own procedures throughout.
How long before the joints can be used?
That comes down to the sealant and the temperature. Some products skin over quickly but need longer to cure fully, and we confirm it before leaving site.
How many days will you need on site?
That varies with the scale of the job, but the work normally takes anything from one day to a planned run of visits, depending on the number of seals and the access. Larger or phased jobs take longer, and we will give you a timescale with the quote.
Which standards are fire seals tested to?
In short, BS EN 1366-3 and 1366-4 are the fire tests and BS EN 13501-2 is how results are classified. An EI 60 seal kept its integrity and insulation for 60 minutes as tested and the installation has to match the test.
Is it fine to apply new sealant on top of old?
No. We cut the old material out and clean the joint back before sealing, since fresh sealant will not bond reliably to aged material.
Does weather matter for sealant work?
It can, for external work. Sealant won’t bond properly to a wet or frosty joint, so external work may be moved if conditions aren’t right. Internal work is far less affected.
Fire-rated sealing for Risinghurst buildings
For England, the fire stopping of penetrations is dealt with in Approved Document B. Its BS 476 references are being withdrawn from 2 September 2029, with BS EN 13501-2 classification taking over, subject to transitional arrangements. Either way, we install the specified product to its tested detail. Risinghurst has six care or nursing homes no more than 2 miles away. In a care home, any new pipe or cable through a fire-resisting wall should be sealed to the specified detail.
Theatres, wards and plant rooms at sites like The Manor Hospital, 1.1 miles west of Risinghurst, all have compartment walls crossed by services. For a site team at a college like Oxford Sixth Form College (2.8 miles west of Risinghurst), fire-rated sealing is best scheduled after the summer works.
Risinghurst is about 2 miles east of Oxford, in Oxfordshire. Across the OX3 postcode area, it works the same way: send details, get a fixed quote, we seal, and the work is guaranteed. 423 places across Oxfordshire fall within our area, including Risinghurst.
Anyone looking for fire stopping in OX3 gets the same process as the rest of our area: details, then a fixed price, then sealing and a 12-month guarantee. We cover commercial and managed buildings on Mark Road, Kiln Lane and Pitts Road. Nearby places we also cover include Shotover Hill (1 mile south), Barton (1 mile north-west), Forest Hill (2 miles east), Horspath (2 miles south-east) and Stanton St John (2 miles north-east). Further afield, our area takes in Didcot (11 miles south), Bicester (10 miles north), Abingdon-on-Thames (7 miles south-west), Witney (13 miles west), Thame (9 miles east) and Wantage (15 miles south-west).
Near you in Risinghurst
Locally, jobs take us to sites close to Stansfeld Park, Cheney School and Holy Trinity Church, among other places. You’ll also find Headington Quarry Foundation Stage School (under half a mile west) and The Six Bells pub (less than half a mile west). The nearest railway station is Oxford station, roughly 3.5 miles west. Nearby you’ll also find Templars Square (2.2 miles south-west) and Nuffield Orthopaedic Centre (0.9 miles south-west). For a walk, there’s Shotover and CS Lewis Nature Reserve.
Do you need fire stopping in Risinghurst?
Physical damage is another reason seals stop doing their job. Seals get knocked during maintenance, cut back to add a cable or pulled out when services are swapped.
Typical triggers for a call:
- Openings found when ceilings come down for a refit
- Old intumescent sealant that has split away
- Penetration schedules that need working through
- Open linear gaps along the top of fire-resisting walls
In a retail centre such as Templars Shopping Park (2.2 miles south-west of Risinghurst), any fire-resisting wall between units that is crossed by new services needs sealing to the tested detail.
What to look for in a quote
- What site paperwork they can supply
- Are they CHAS accredited or on Constructionline?
- How the joint faces will be prepared and primed
- Is the sealant right for the movement and the substrate?
When it isn’t the sealant
Our job is the joint, not everything around it. On its own, sealant can’t deal with:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Openings that need collars, wraps, batts or boards rather than sealant
- Issuing fire ratings or certificates for seals
If you are not sure, just phone 01277 525 020 or use the quote form and we will give you a straight answer before you book.
What we seal
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
- Pipe penetrations
- Small duct penetrations where the tested detail allows
- Cable penetrations
- Service gaps in risers