Fire-rated sealing and fire stopping in Meadvale, Surrey
Our CSCS-carded applicators take on fire-rated and intumescent sealing of service penetrations and linear gaps in Meadvale. Send photographs or drawings for a fixed quote.
- Fire sealant pulled out of the opening
- Head-of-wall gaps with no fire seal
- Unsealed penetrations discovered above suspended ceilings
Fire stopping in Meadvale
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How we handle fire stopping in Meadvale
We should be clear about what we do and don’t do. The designer, fire engineer or building control decides which fire stopping is required. What we bring is careful installation of the specified sealant, to the maker’s guidance. We work on pipe penetrations, joints between fire-resisting walls and floors and cable penetrations, and the usual reasons a site gets in touch are builders’ foam or ordinary silicone in compartment walls and unsealed penetrations discovered above suspended ceilings. A single leaking joint is often how a building in Meadvale first comes to us: we look at the rest while we’re there and tell you what we find.
Around Meadvale, penetration and linear seals tend to be one-building jobs. With the specification and photos of the gaps, we can give a fixed quote and bring the right products.
Building owners and contractors get the same cover: a 12-month guarantee on our workmanship. Faults in the structure, damage and other trades’ work fall outside it, and we say so plainly.
- Where
- Meadvale (RH2, RH1)
- Wider area
- Surrey
- Cover
- 12 months on every job
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Cost factors for service penetrations
Quotes vary with the job. It mainly depends on:
- Location, for remote and island sites
- Removal of failed or old sealant
- Access and working height
- Specialist products, such as fire-rated or hygienic sealants
What a job costs comes down to the quantity of joints, what has to come out first and the access. Call for a quote once you have the details.
Sending details for a quote
The more we know, the firmer the quote. Helpful details to send:
- Access details, including height
- When you need the work done
- Asbestos survey details if the building is older
- The postcode of the building
We quote a fixed sum against the scope you give us, so the cost is agreed before work starts. To start the process, ring 01277 525 020 or email a schedule or drawings.
FAQs: Meadvale
What happens to BS 476 references for fire stopping in Meadvale?
From 2 September 2029, Approved Document B drops its BS 476 references in favour of BS EN 13501-2 classification, with transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Can you work around term dates at a campus such as Reigate College?
Yes. Education sites typically want the work in vacations or in phases during term, and we plan to suit. Tell us which site documents you need, such as RAMS, our insurance certificate or CSCS details, and they’re confirmed with the quote.
What will the job cost?
There isn’t a price list, as every site differs. With photos or drawings, we can give you a fixed quote.
Is the work guaranteed?
Yes. Workmanship is guaranteed for 12 months.
Is any job too small?
We quote for single jobs as well as large packages and programmes. Photos and a description are enough to start.
When is resealing likely to be due?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Sealant joints are maintenance items, so inspect them regularly.
Is Meadvale in your area?
Yes. Meadvale falls within our area, and the simplest way to start is to phone 01277 525 020 or email drawings and photos.
After the work
Every sealant joint needs some looking after, and their life depends on movement, exposure, cleaning and use. We suggest:
- Foam or ordinary sealant is never a fire-seal repair
- Leave fire sealant to cure fully before covering it
- Put resealing into every M&E and fit-out package
- Treat an open penetration as a priority repair
Allow the manufacturer’s stated cure time before boxing in or decorating. Some fire-rated sealants accept paint and some don’t, so check the product data first.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. That way the opening is sealed while the trade and access are still there.
What sealant work can’t fix
Part of a good diagnosis is knowing where sealant stops. We’ll tell you if the real problem is any of the following:
- Plastic pipes whose detail calls for a collar or wrap
- Issuing fire ratings or certificates for seals
- Gaps in walls that were never built as compartment walls
If in doubt, call the office on 01277 525 020 or email drawings and photos and we will say what we think before you book.
Where we work in Meadvale
- Small duct penetrations where the tested detail allows
- Joints between fire-resisting walls and floors
- Service gaps in risers
- Cable penetrations
- Linear gaps at wall heads
- Pipe penetrations
Fire stopping in Meadvale: the local picture
Meadvale lies roughly 19 miles out from central London. Office refits around the commuter belt bring new cabling through fire-resisting walls. For England, the fire stopping of penetrations is dealt with in Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. Our part stays the same: the specified product, installed to its tested detail.
For a school such as Reigate School, penetration sealing fits best at the end of the summer works. For a hospital such as East Surrey Hospital, 1.2 miles south-east of Meadvale, penetration sealing is typically phased ward by ward, with infection-control rules agreed first. On a site such as Kingsfield Business Centre, which lies north-east of Meadvale, every fit-out that runs new services through a compartment wall leaves penetrations to seal with the specified product.
Meadvale is about 1 mile south-east of Reigate, in Surrey. Looking for fire stopping in Meadvale? We can help, as we do across Surrey. We work across 379 places in Surrey. Sites around London have their own page, about 19 miles away.
Postcode districts covered here: RH2 and RH1 for service penetrations. We cover commercial and managed buildings on Hazel Road, Willow Road and Arbutus Road and the roads nearby. With the A2044 nearby, Meadvale is straightforward for us to reach. We also cover Earlswood (1 mile east), Redhill (1 mile north-east), South Earlswood (1 mile south-east), Holmethorpe (2 miles north-east) and Salfords (2 miles south-east) for service penetrations. Nearby towns on our patch include Epsom (8 miles north-west), Horley (3 miles south), Ewell (9 miles north), Walton-on-Thames (14 miles north-west), Caterham (6 miles north-east) and Dorking (6 miles west).
Around Meadvale
Locally, jobs take us to sites close to Dunottar School, The Old Oak pub and Earlswood Common. The nearest railway station is Earlswood (Surrey) station, about 0.7 miles east of the centre. Other landmarks nearby include The Belfry (1.2 miles north-east) and Reigate Priory Museum (1 mile north-west). Open spaces near Meadvale include Reigate Heath and Colley Hill.
Nearby places to Meadvale
Also in Meadvale
Why deal with it now?
Fire stopping is a regular point raised at inspections and handover. Late discoveries can delay handover while openings are reopened and resealed. Sealant hardens, cracks and loses grip with age, UV and movement. Renewing it in good time keeps the building weathertight.
Whether it’s a single area or a whole estate, the same things set the price: what’s in scope, how we reach it, what’s specified and when it needs doing. Call for a quote, and you will have a fixed figure to work with.
Why appoint us
- Fully insured, including public liability cover
- Work to your specification and the manufacturer’s guidance
- 12 months’ guarantee on every job
- CSCS-carded applicators
See our cost guide or how we’re accredited.
Our process
Tell us your site hours and access windows and we will plan around them. While we’re working, the area stays contained and tidy, and we check in with your contact before moving on to each new area. For a job in Meadvale, the main thing is a clear picture of the work. A fixed quote follows.
- First we confirm the product and tested details named in the specification.
- We sort the openings by the detail each one needs.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- We gun the sealant in to the specified depth around each service and tool it.
- We walk the completed areas with you and confirm the records agreed at quote stage.
What we need from you
- Arrange parking or a loading space
- Agree which areas must stay open
- Tell us what induction or permit system the site runs
Get a fixed quote
For a fixed quote, phone 01277 525 020 or email a schedule or drawings, telling us the site location and the nature of the job. You can also send details through our quote form.
Read more
Should maintenance staff do it?
Certain joints really need a specialist: for example fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. Getting these wrong normally costs more in the end than doing them right.
What you see is the finished bead, but most of the work is hidden. Backing rod, primer where specified and a joint designed to move with the building are easy to get wrong without experience.