Fire Stopping in Long Hanborough
Fire stopping in Long Hanborough, backed by over 20 years in commercial sealing. Fully insured and CHAS accredited.
- Unsealed penetrations discovered above suspended ceilings
- Fire stopping installed outside its tested range
- Old intumescent sealant that has split away
Fire stopping in Long Hanborough
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Signs you need fire stopping in Long Hanborough
Plenty of openings were simply never closed because they sat out of sight above a ceiling or inside a riser. Inspections, refurbishments and ceiling access usually bring them to light.
It’s worth sending us details if you spot any of the following:
- Damaged fire seals in risers and voids
- Openings found when ceilings come down for a refit
- Fire-rated sealant that has cracked or shrunk back
- Snag lists that include open service penetrations
For an estates team at a campus like University Field Station, 4.4 miles to the south-east of Long Hanborough, summer M&E works are usually followed by a round of penetration sealing.
Before you book anyone
- Whether primer will be used where the manufacturer specifies it
- How they’ll work around occupants
- Health and safety accreditation such as CHAS
- The named product and why it was chosen
Fire stopping in Long Hanborough, done properly
Where pipes, cables and other services cross a compartment wall or floor, the opening around them has to be closed so fire and smoke can’t move between compartments. Our job is fitting fire-rated and intumescent sealant at those service penetrations, and along linear gaps, where it is the specified product. We work to the product’s tested detail for every seal. Site teams most often ask us about openings found when ceilings come down for a refit and fire-rated sealant that has cracked or shrunk back, on linear gaps at wall heads, small duct penetrations where the tested detail allows and pipe penetrations. Whoever orders the work in Long Hanborough, the brief is normally the same: a clear scope, tidy work and joints that don’t fail again.
Around smaller places like Long Hanborough, many commercial buildings are conversions or extensions of older ones, so it’s worth confirming the wall or floor type before choosing the seal. We match the product to the substrate and service, and say so if a collar, wrap or batt is the specified item.
Every job is signed off with a 12-month guarantee. The promise is simple: if our work fails within that year, we put it right.
- Location
- Long Hanborough (OX29)
- Wider area
- Oxfordshire
- Cover
- 12 months on our workmanship
- Quotes
- Quoted before any work starts
- Call
- 01277 525 020
- Updated
- 3 November 2026
Questions about Long Hanborough
What happens to BS 476 references for fire stopping in Long Hanborough?
References to BS 476 classes are being removed from Approved Document B from 2 September 2029, after which BS EN 13501-2 classification is the route, subject to transitional arrangements. Whichever applies, we install the specified product to its tested detail; the specification is for the designer to set.
Is a smaller place like Long Hanborough outside your area?
Not at all. Long Hanborough is within our area. We work across Greater London and the South East. Send photographs and a list of what needs doing, and we will plan the job to need as few trips as possible.
Are you insured?
Yes. We are fully insured, including public liability cover.
Is any job too small?
Small jobs are welcome alongside larger packages. Send details for a fixed quote.
Do your applicators hold CSCS cards?
Yes. We use CSCS-carded applicators, which many sites require.
What happens if old sealant might contain asbestos?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and work stops until any suspect material has been tested. Removing asbestos is a job for asbestos specialists, not us.
How many days will you need on site?
The duration is planned around your programme and the access we are given. We will give you an estimate of time on site when we quote.
What affects the price in Long Hanborough
Each job is priced on its own details. The things that drive the figure:
- Whether old sealant has to be cut out first
- Travel to remote or island sites
- Site requirements such as inductions and permits
- Specialist products, such as fire-rated or hygienic sealants
Access can matter as much as the joints themselves: joints within easy reach take less time than ones that need access equipment. Mention the access as part of your enquiry.
What to include in your enquiry
We can often quote from photographs and a few details. Please tell us:
- Asbestos survey details if the building is older
- What the building is and how it’s used
- Clear photographs of the problem areas
- Drawings or a marked-up plan, if available
A good quote starts with a clear picture: what’s there, how much of it, how we reach it and what’s specified. Share whatever details you have and we’ll fill any gaps with a visit.
From enquiry to sign-off
Before any cutting starts, the area is protected: masking tape along the joint edges and sheeting over anything nearby. The work itself usually takes anything from one day to a planned run of visits, depending on the number of seals and the access, and our waste is bagged and taken away as we go. For a job in Long Hanborough, the main thing is a clear picture of the work, so send photos of each area. You’ll then get a fixed price for the work.
- We start with your penetration schedule, drawings or specification.
- Access, permits and the order of areas are agreed with the site team.
- We compare every service penetration with its tested detail before sealing.
- Foam, ordinary sealant and debris come out so the seal starts clean.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
What we need from you
- Let building users know which areas are affected
- Let us know about inductions and permits
- Move anything stored against the joints
Getting a fixed quote
Tell us about the building, the joints and when you need the work done, and we’ll put a fixed quote together. The easiest way is to call the office on 01277 525 020 or use the quote form.
Advice
Leave it or put it right?
Open service penetrations matter on ordinary days, not just in a fire: smoke, noise and draughts pass through them every day. Sealing them to the specified detail deals with the fire risk first, and the other benefits follow. Over time, UV, weather and movement wear any sealant out. Replacing it before it fails keeps water out.
No two sites price the same: the joint sizes, the specified product, access and working hours each have a bearing. Send the details and a fixed figure follows.
What you get with us
- Fully insured, including public liability cover
- A fixed quote before work starts
- CSCS-carded applicators
- Work to your specification and the manufacturer’s guidance
Read how commercial sealant jobs are priced and our accreditations and insurance.
When it isn’t the sealant
Not every problem is a sealant problem, and we are upfront when that’s the case. It won’t fix:
- Construction that lacks the fire resistance the seal relies on
- Writing the fire-stopping specification
- Reviewing a building’s overall fire safety
If you’re not sure, just call the office on 01277 525 020 or email a schedule or drawings and we will give you a straight answer.
Where we work in Long Hanborough
- Small duct penetrations where the tested detail allows
- Linear gaps at wall heads
- Service gaps in risers
- Joints between fire-resisting walls and floors
- Cable penetrations
- Pipe penetrations
Penetration seals near Long Hanborough
Long Hanborough lies roughly 60 miles out from central London. Tenant changes on commuter-belt business parks mean regular fit-outs, and new services through compartment walls. In England, Approved Document B covers fire stopping of openings and penetrations. From 2 September 2029, BS 476 references are being taken out of Approved Document B, leaving BS EN 13501-2 classification as the route, subject to the Government’s transitional arrangements. What we install is set by the specification, and it goes in to the tested detail.
For a unit at a site such as Wroslyn Road Industrial Estate, which lies south-west of Long Hanborough, new power or data runs between office and warehouse can breach a compartment wall. In a building such as Christ Church, any service penetration through a fire-resisting wall should be sealed to the specified detail.
Long Hanborough is about 5 miles north-east of Witney, in Oxfordshire. Long Hanborough sits inside our coverage, with the same fixed quotes and 12-month guarantee as everywhere else. Across Oxfordshire, 423 places are covered, Long Hanborough among them. Our Oxford page has more on work in that area.
If you need fire stopping in OX29, the process matches everywhere else we work: send details, get a quote, we seal, guaranteed. We cover commercial and managed buildings on Church Road, New Road and Churchill Way and the roads nearby. We also cover Church Hanborough (1 mile south-east), Bladon (2 miles east), Woodstock (3 miles north-east), Worton (3 miles south-east) and Begbroke (3 miles east). A short drive away, we cover Oxford (9 miles south-east), Bicester (12 miles north-east), Abingdon-on-Thames (11 miles south-east), Witney (5 miles south-west), Carterton (9 miles south-west) and Grove (15 miles south).
Around Long Hanborough
In Long Hanborough, that means premises near Three Horseshoes pub and the streets around them. Long Hanborough’s nearest station is Combe station, roughly 0.6 miles north. A little further out are Morris Motors Museum (1 mile east). Open spaces near Long Hanborough include Blenheim Farm.
Other services in Long Hanborough
General trades versus a specialist
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and we will confirm the paperwork you need with the quote.
For most general trades, sealant is a sideline. A specialist brings correct preparation, depth control with backing rod and a product suited to that particular joint, which is what makes a joint last.