Fire Stopping in Lintmill
Fire-rated and intumescent sealing of service penetrations and linear gaps throughout Lintmill and nearby, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Builders’ foam or ordinary silicone in compartment walls
- Head-of-wall gaps with no fire seal
- Seals disturbed by maintenance and left open
Fire stopping in Lintmill
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
When something else is needed
Honesty saves time and money. New sealant won’t cure:
- Designing or specifying fire stopping, which sits with the designer or fire engineer
- Walls or floors that aren’t fire-resisting to begin with
- Fire risk assessments, a job for a competent assessor
If you’re not sure, just give us a call on 01277 525 020 or send photos by email and we’ll give you a straight answer.
Where we work in Lintmill
- Service gaps in risers
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
- Cable penetrations
- Pipe penetrations
Fire stopping in Lintmill
Fire-rated sealant suits many small service penetrations: copper and steel pipes, cables and some small ducts where the tested detail allows. Other openings need collars, wraps, batts, pillows or boards. If the detail calls for something other than sealant, we say so rather than force sealant into it. If you’re dealing with openings found when ceilings come down for a refit and expanding foam used as fire stopping, we can help. Sealant applicators who only do sealant are a different proposition from a general trade with a gun in the van: in Lintmill, that means joint design, primers and backing rod as standard.
Hotels and care homes around smaller places like Lintmill often have services added during refurbishment. We fit the specified fire-rated sealant as its published detail shows and raise it if another product is needed.
Our 12-month guarantee is about workmanship, not wear and tear. Sealant wears with time, and movement, weather, cleaning and use decide how fast, so we are clear about what is covered before work starts.
- Place
- Lintmill (AB56)
- Wider area
- Moray
- Cover
- A 12-month guarantee
- Quote
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Last updated
- 3 November 2026
Penetration seals near Lintmill
There are a number of hotels within about 2 miles of Lintmill. In hotels, bedroom and corridor walls are usually fire-resisting, so services added in a refit need sealing with the specified product. Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, using products tested for the way they’re used. We install fire-rated sealant to that tested detail where it is specified.
In a building such as St Mary's Collegiate Church, any service penetration through a fire-resisting wall should be sealed to the specified detail. Hotels like Grant Arms Hotel, 1 mile to the north of Lintmill, are refurbished in phases, and each phase can open up compartment walls. Wherever services are added at a hospital such as Campbell Hospital, 4.2 miles east of Lintmill, the compartment line has to be made good with the specified product.
Lintmill is about 6 miles east of Buckie, in Moray. We cover Lintmill and the rest of Moray, and jobs here get the same fixed quote and 12-month guarantee as anywhere else. Lintmill is one of 59 places in Moray on our list. There’s a separate page for Aberdeen, about 44 miles away.
Anyone looking for fire stopping in AB56 gets the same process as the rest of our area: details, then a fixed price, then sealing and a 12-month guarantee. We also cover Cullen (1 mile north), Sandend (2 miles east), Portknockie (3 miles north-west), Fordyce (3 miles east) and Findochty (4 miles north-west) for service penetrations. Bigger towns within reach include Buckie (6 miles west), Keith (11 miles south-west), Fochabers (11 miles south-west), Ianstown (5 miles west), Lhanbryde (15 miles west) and Portessie (5 miles west). For island and remote sites, travel and materials need planning ahead, so the full address helps from the start.
Around Lintmill
Other landmarks nearby include Campbell Hospital (4.2 miles east) and castle 30m NNW of Inaltry (1.5 miles south). For a walk, there’s Durn Hill.
What the job involves on each surface
Small ducts
Small ductwork can sometimes be sealed with sealant where the tested detail includes it. Larger or fire-rated ductwork usually needs a different solution set by the designer and we flag that rather than guess.
Cables and cable bundles
Data cabling added after handover is a regular cause of open service penetrations. We reseal around them to the specified detail, and any bundle too large for sealant alone is flagged.
Your questions answered
Which Scottish guidance covers penetration seals in Lintmill?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. Design sits with the designer and the verifier; installation to the tested detail is our part.
Can you work on a hospital site such as Campbell Hospital?
Yes. Healthcare sites are among the places we work. Each area is agreed with the ward or department and the estates team in advance.
What if there’s asbestos in the old mastic?
Some older mastics, especially in pre-2000 buildings, can contain asbestos. We check the asbestos register before cutting out old sealant in an older building, and if asbestos is suspected, work stops until it’s tested. We don’t remove asbestos-containing materials.
Can one quote cover more than one building?
Yes. A group of buildings can go on one quote, and you deal with one contact throughout across South East England, Greater London and Scotland.
Do you guarantee your work?
Yes, for 12 months. If our installation fails in that time, we return and fix it.
Are your applicators CSCS-carded?
Yes. If you need card details for site access, tell us and we will confirm them with the quote.
Do you need to see the site first?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we will arrange a visit before quoting.
Looking after the joints
Keep the joints in good shape with a few simple steps:
- Ask the designer to confirm details early on refits
- File the specified details where the next contractor can find them
- Ask which product is in place before decorating
- Treat an open penetration as a priority repair
After the work, brief anyone else working in the area that the openings are now sealed. If a seal has to be opened for a new service, it should be reinstated to the same detail, by someone who knows the system.
On fit-outs, get the fire-stopping specification agreed before the services go in. Details can then be picked to suit the actual pipes, cables and ducts.
What affects the price in Lintmill
A fixed quote reflects the actual work. It takes account of:
- The size and state of each joint
- The product specified
- Quantities, in metres or numbers
- Access and working height
We don’t publish prices, since every building and every scope is different. For a fixed figure, call for a quote.
What we need to price the job
For an accurate fixed quote, we need a clear picture of the site. Send us:
- Whether the building will be occupied during the work
- Anything awkward about access or site hours
- Where the site is, with the postcode
- Drawings or a marked-up plan, if available
Quotes are fixed against the scope you send, so you know the figure before anyone is on site. To start the process, call 01277 525 020 or use the quote form.
Owners, agents and contractors
As a CHAS accredited contractor and Constructionline member, we make supplier vetting simple. Our insurance certificate can be sent along with the quote.
When you manage a building on behalf of an owner, you need clear quotes and clear reporting. You get a fixed quote, an agreed scope and a walk round at the end, plus a 12-month guarantee.
What else we do in Lintmill
Diagnose, treat, sign off
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Any old material is cut back to clean, sound faces, the manufacturer’s primer is applied where it’s called for, and each bead is tooled to a neat concave finish. Where we can, we combine work around Lintmill with other jobs nearby, to make the most of each trip. Tell us how flexible your dates are.
- First we go through the drawings, schedule or specification for the seals.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Anything that doesn’t belong in the opening, such as expanding foam or general-purpose filler, is removed.
- We fit the backing the detail asks for, to the stated depth.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
What we need from you
- Tell us what induction or permit system the site runs
- Clear stock, furniture or equipment away from the joints
- Tell us your opening times and when work is allowed
Get a fixed quote
Pricing a project or setting a maintenance budget? We will quote against your scope and drawings that you can work with. If you have questions first, phone 01277 525 020 or use the quote form.