Fire-rated sealing and fire stopping in Forth, South Lanarkshire
Fire stopping for Forth, from a contractor working since 2005. Fully insured and CHAS accredited.
- Head-of-wall gaps with no fire seal
- Service penetrations left open after M&E works
- Old intumescent sealant that has split away
Need fire stopping in Forth?
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Where services cross fire walls in Forth
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, with products tested for that end use. We install fire-rated sealant to that tested detail where it is specified.
Wherever the building is near Forth, design and sign-off of fire stopping sit with the designer, fire engineer or building control; we install what has been specified.
Forth is about 6 miles north-east of Carluke, in South Lanarkshire. We cover commercial sites throughout Forth, whether it’s a single job or part of a planned programme. Forth is one of 134 places we cover in South Lanarkshire for service penetrations. Our Edinburgh page has more on work in that area.
Commercial sites across ML11 are covered. If your site is on Main Street, Forkens and Hailstonegreen or close by, we can quote for service penetrations. Just outside Forth, we also work in Greenwall (1 mile north-west), Wilsontown (1 mile north-east), Climpy (1 mile north-west), Haywood (2 miles north-east) and Braehead (2 miles south-east). Nearby towns on our patch include Hamilton (14 miles west), Larkhall (11 miles west), Carluke (6 miles south-west), Lanark (7 miles south-west), Bothwell (15 miles west) and Burnbank (15 miles west).
What’s near Forth
Forth’s nearest station is Fauldhouse station, about 4 miles north of the centre. A little further out are Couthally Castle (4 miles south-east).
About our fire stopping in Forth
We are commercial sealant applicators, CHAS accredited and a Constructionline member, with CSCS-carded applicators on site. We don’t hold a third-party fire-stopping installer certificate, and we won’t pretend otherwise. We install the specified fire-rated sealant to its tested detail, and our workmanship carries a 12-month guarantee. If you have improvised or mixed-product fire seals and unsealed openings around new pipes and cables, we can help, on small duct penetrations where the tested detail allows, linear gaps at wall heads and cable penetrations alike. One point of contact handles commercial sealant work in Forth from the first photos to the final walk-round, for single jobs and planned programmes alike.
For a building near Forth, we plan fire-rated sealing so it’s finished in one visit where possible. Send the specification and photos of the openings, with sizes if you have them.
Our workmanship is guaranteed for 12 months, wherever the site is. If our installation lets you down in that time, we return and fix it.
- Location
- Forth (ML11)
- Wider area
- South Lanarkshire
- Cover
- 12 months on our workmanship
- Quote
- A fixed quote before we start
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Maintenance after handover
Problems stay small when the joints are checked regularly. Specifically:
- Agree the fire-stopping specification before services go in
- Flag new cables with no seal around them
- Keep product data and details in the fire safety file
- Get seals inspected before ceilings and boxing close
Don’t patch a fire-rated seal with anything outside its tested detail. A repair should use the original product, installed the same way.
On fit-outs, get the fire-stopping specification agreed before the services go in. The designer can then choose details that suit the services planned, and installation follows the programme.
Leave it or put it right?
Leave a penetration open and smoke and fire can cross into the next compartment far earlier than intended. While the openings can be reached, sealing them is normally straightforward. Left until ceilings are closed or a tenant moves in, the same work costs more access and more disruption. For buildings near Forth, dealing with all the failing joints at once saves return trips. Photos of each area help us quote the whole job.
The product called for affects the cost, as does the preparation each joint needs, such as cutting out, priming or new backing rod. Access, phasing and site requirements come into it too.
Why us?
- Work to your specification and the manufacturer’s guidance
- Constructionline member
- One phone line for London, the South East and Scotland
- Health and safety: CHAS accredited
See how commercial sealant jobs are priced or how we’re accredited.
From enquiry to sign-off
Working in a building that stays open takes some planning. The work area is signed and kept contained, with routes through the building left open and work section by section so the rest of the building stays in use. For work around Forth, we aim for one trip, so photos, sizes and a full list matter. Outside work also needs a suitable weather window.
- We ask for the product and detail your designer has specified.
- Openings are measured and grouped by detail.
- Old or wrong materials are cut out.
- Mineral wool or other backing is fitted where required.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- Completed areas are checked with you, with the records agreed when we quoted.
Getting the site ready
- Tell us which areas need to stay in use
- Move anything stored against the joints
- For older buildings, check the asbestos register before work
Get a fixed quote
Pricing a project or setting a maintenance budget? We will quote against your scope and drawings you can plan around. If you have questions first, call 01277 525 020 or email drawings and photos.
Related advice
What sets the cost
We price every job individually. The things that drive the figure:
- Backing rod, priming and other preparation
- Induction, permit and paperwork requirements
- Whether the work must be split into stages
- The total length or number of joints
Larger quantities, tricky access or phasing all shape the price. So do site requirements such as inductions and permits.
Sending details for a quote
Good information means a firmer quote. When you get in touch, include:
- Where the site is, with the postcode
- Clear photos of the problem areas
- Whether the building will be occupied during the work
- Rough lengths or quantities, or drawings if you have them
Send details, get a quote, we seal, guaranteed: that’s how every job runs. To take the first step, give us a call on 01277 525 020 or use the quote form.
When to call us in Forth
Fire stopping can get squeezed at the end of a programme, or done by whoever is on site. That is how unsuitable products and improvised details end up in compartment walls.
Look out for the following:
- Old intumescent sealant that has split away
- Service penetrations left open after M&E works
- Builders’ foam or ordinary silicone in compartment walls
- Fire stopping installed outside its tested range
For buildings in and around Forth, fire-rated sealant is installed where it is specified, to the manufacturer’s tested detail.
What your quote should include
- How they handle RAMS and site documents
- Health and safety accreditation such as CHAS
- Proof of insurance
- Is the sealant right for the movement and the substrate?
Places near Forth
Also in Forth
FAQs: Forth
Can you produce the fire-stopping design for a job in Forth?
No. Fire-stopping design and sign-off belong to the designer, principal designer, fire engineer or building control. We install fire-rated and intumescent sealant around service penetrations and linear gaps where it is specified, to the manufacturer’s tested detail.
How do Scotland’s building standards affect fire-rated sealant in Forth?
Under Scotland’s non-domestic Technical Handbook (clause 2.1.14), service penetrations should keep at least the wall or floor’s fire resistance duration, using products tested for their end use. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
How long will the new sealant last?
Nobody can honestly give a figure in years, since movement, weather, cleaning and use all affect it. Regular checks let you plan resealing before leaks or damage.
Do you work to architects’ specifications?
Yes. The specification and the manufacturer’s installation guidance are what we work to, and we raise anything unclear before work begins.
Is Forth in your area?
Yes. We cover Forth and the rest of South Lanarkshire. For a quote, call 01277 525 020 or email a schedule or drawings.
Is colour matching possible?
In many cases, yes. Sealants are made in a wide range of standard colours, and matching to RAL references or nearby finishes is commonly requested. We will confirm the colours available for the specified product.
How many days will you need on site?
We plan the time on site around your programme and access. You will have an expected duration with the quote.
For managing agents and facilities managers
We work for building owners and managing agents on sealant work across single buildings or whole portfolios around Forth. Several sites can go on one quote, so there’s one set of paperwork to deal with.
FMs need a contractor who is easy to get on site. Tell us what site paperwork you need, such as RAMS, an insurance certificate or CSCS details, and we’ll confirm with the quote.