Fire Stopping in Cunninghamhead
We carry out fire-rated and intumescent sealing of service penetrations and linear gaps in Cunninghamhead. Send details for a fixed quote.
- Open linear gaps along the top of fire-resisting walls
- Unsealed penetrations discovered above suspended ceilings
- Damaged fire seals in risers and voids
Fire stopping for Cunninghamhead sites
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
How the quote is worked out
Your fixed quote is built from the real scope. It allows for:
- How accessible the joints are
- Quantities, in metres or numbers
- Which sealant the job calls for
- The site’s rules and procedures
Pricing service penetrations depends on how many there are, their condition and the access, and any specification that applies. Call for a quote.
Sending details for a quote
For an accurate fixed quote, we need to understand the site. Useful things to include:
- A wide shot and a close-up of the area
- Whether an asbestos survey exists
- Specification clauses that apply
- Rough lengths or quantities, or drawings if you have them
Photos, drawings or a schedule of the joints are often enough for a fixed quote. If the job needs a look first, we’ll arrange a site visit.
Fire stopping in Cunninghamhead, done properly
Penetration seals are fire tested to BS EN 1366-3 and linear joint seals to BS EN 1366-4. A rating such as EI 60 only holds when the product is installed as it was tested. So our job is to reproduce that arrangement faithfully. Most enquiries involve open linear gaps along the top of fire-resisting walls and seals that don’t match their tested detail, across linear gaps at wall heads, cable penetrations and small duct penetrations where the tested detail allows. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Cunninghamhead it comes down to the same thing: failed joints cut out, faces prepared and the right sealant laid to the right depth.
Travel to smaller places like Cunninghamhead is planned so every penetration is sealed on one trip. Photos of the gaps, the services and the wall or floor type help us bring the right products.
Whoever the client is, the cover is the same: twelve months on the work we carried out. It doesn’t extend to damage, faults in the building or work by others, and we are upfront about that.
- Where
- Cunninghamhead (KA3)
- Region
- North Ayrshire
- Guarantee
- 12 months on our workmanship
- Quote
- A fixed quote before we start
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
Diagnose, treat, sign off
On arrival, we report to your site contact and complete whatever induction the building runs. Everything around the joints gets protected before any cutting starts, and the work usually takes longer where risers, ceiling voids or occupied floors have to be worked through in sequence. Tell us who will meet us and how to get in at your building near Cunninghamhead. That goes into the plan alongside the quote.
- The specification and schedule come first, so we know which details apply.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Foam, ordinary sealant and debris come out.
- Backing and fire-rated sealant are installed to the detail and tooled.
- Anything outside the detail is reported to you rather than sealed.
Before we start on site
- Agree which areas must stay open
- Warn occupants and staff about the work
- Send any specification or drawings in advance
Get a fixed quote
For a fixed quote, call 01277 525 020 or email drawings and photos with the site address and an outline of the work. Our quote form is another easy route.
Read more
When to call us in Cunninghamhead
Some seals fail because the wrong product went in: expanding foam or a general-purpose sealant pushed into a gap to tidy it. It may look closed, but it has no tested fire performance in that position and has to be removed.
Any of the following is a good reason to get the joints checked over:
- Open linear gaps along the top of fire-resisting walls
- Openings left by services added after handover
- Damaged fire seals in risers and voids
- Fire sealant pulled out of the opening
At a healthcare site like University Hospital Crosshouse (2.7 miles south-east of Cunninghamhead), new services through compartment walls are a constant, and each needs the specified seal.
What your quote should include
- What level of public liability insurance do they hold?
- Which product they’ll use, and why it suits the joint
- Whether old or failed sealant will be cut out, not overlaid
- How joint depth will be controlled
When something else is needed
We check first that sealant really is the fix. It isn’t the answer for:
- Fire doors, dampers or other fire safety equipment
- Plastic pipes whose detail calls for a collar or wrap
- Approving the work on behalf of building control
Not sure which it is? You can phone 01277 525 020 or email the details over and we’ll tell you honestly.
What we seal
- Pipe penetrations
- Service gaps in risers
- Small duct penetrations where the tested detail allows
- Cable penetrations
- Linear gaps at wall heads
- Joints between fire-resisting walls and floors
Looking after the joints
After handover, these steps help:
- Leave fire sealant to cure fully before covering it
- Agree the fire-stopping specification before services go in
- Don’t let anyone top up a fire seal with the wrong product
- Check risers and ceiling voids after each round of works
Once the seals are in, tell other trades they exist and must not be disturbed. Any seal cut back for a new service needs reinstating to its tested detail using the same product.
Write fire stopping into the scope of any work crossing a compartment wall or floor. That way the opening is sealed while the trade and access are still there, not months later.
Fire stopping in Cunninghamhead: the local picture
Under the Scottish non-domestic Technical Handbook, clause 2.1.14, penetrations should be fire stopped to at least the wall or floor’s fire resistance duration, and products should be tested for their end use. We install fire-rated sealant to that tested detail where it is specified.
Buildings near Cunninghamhead get the fire-rated product that’s specified, installed to its tested detail.
Cunninghamhead is about 3 miles north-east of Irvine, in North Ayrshire. Looking for fire stopping in Cunninghamhead? We can help, as we do across North Ayrshire. We work across 54 places in North Ayrshire, large and small. For work in that direction, see our Glasgow page, about 19 miles away.
If you need fire stopping in KA3, the process matches everywhere else we work: details, then a fixed price, then sealing and a 12-month guarantee. If your site is on Altonhead Drive and Altonhead Terrace or close by, we can quote for service penetrations. If your building is just outside Cunninghamhead, we cover Kilmaurs (2 miles east), Knockentiber (2 miles south-east), Springside (2 miles south), Lady's Well (2 miles east) and Crosshouse (3 miles south-east). A short drive away, we cover Irvine (3 miles south-west), Kilwinning (5 miles west), Saltcoats (8 miles west), Largs (15 miles north-west), Ardrossan (9 miles west) and Stevenston (7 miles west).
Near you in Cunninghamhead
For rail, the closest station is Kilmaurs station, roughly 2 miles east. Other landmarks nearby include Cunninghamhead Estate (0.6 miles west) and University Hospital Crosshouse (2.7 miles south-east). For a walk, there’s Caprington Loch and Dunlop Hill.
When to bring in a specialist
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and we will confirm the paperwork you need with the quote.
What you see is the finished bead, but most of the work is hidden. Correct depth, the right primer and a sealant matched to the movement are easy to get wrong without experience.
Questions about Cunninghamhead
How do Scotland’s building standards affect fire-rated sealant in Cunninghamhead?
The non-domestic Technical Handbook, clause 2.1.14, expects a penetration to keep at least the wall or floor’s fire resistance period, with proprietary products tested for the use they’re put to. The detail is set by the designer and goes through the warrant process; we install the specified product to its tested detail.
Is Cunninghamhead off your patch?
Not at all: smaller places are covered as well as towns. Every Scottish council area is within our area. Good photographs up front let us bring everything on the first visit.
What’s the quickest route to a quote?
It works in four steps: send details, get a quote, we seal, guaranteed. Step one needs little more than photographs and a postcode.
Are you insured?
Yes. Our insurance certificate can be sent alongside the quote.
Can you handle several sites?
Yes. We take on portfolio and planned maintenance work, planned site by site to suit how each building is used.
Can you quote from photographs?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we will arrange a visit.
How long does a typical visit take?
We plan the time on site around your programme and access. We will give you an estimate of time on site when we quote.