Fire-rated sealing and fire stopping in Burford, Oxfordshire
Looking for fire stopping in Burford? Send us the details for a fixed quote, backed by a 12-month guarantee on the work.
- Unsealed openings around new pipes and cables
- Seals disturbed by maintenance and left open
- Expanding foam used as fire stopping
Fire stopping across Burford
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
From enquiry to sign-off
When we get to site, we report to your site contact and complete whatever induction the building runs. Everything around the joints gets protected before any cutting starts, and the work normally takes a single visit for a short list of penetrations, or a phased programme for a whole building. For a job in Burford, the main thing is a clear picture of the work, so send photographs of each area. A fixed quote follows.
- First we go through the drawings, schedule or specification for the seals.
- Every penetration is compared with its detail: wall or floor type, service, gap size and depth.
- Unsuitable fillers and loose debris are taken out of each opening.
- Mineral wool or other backing goes in wherever the detail asks.
- Fire-rated or intumescent sealant is gunned in to the specified depth, then tooled.
- Openings that need a collar, wrap, batt or other product are flagged to you rather than filled with sealant.
What we need from you
- Flag any permit to work we’ll need
- Let building users know which areas are affected
- Send your site hours and access windows
Get a fixed quote
Send us photos, drawings or a joint schedule and a fixed quote comes back to you. Where a site visit makes more sense, we’ll arrange one.
Advice
How we handle fire stopping in Burford
Opened ceilings and riser doors often reveal service openings nobody sealed. Where the walls and floors already have a fire-stopping specification, we can work to it, matching the product and detail it names. With no specification in place, the first step sits with your designer or fire engineer, not with us. Most enquiries involve improvised or mixed-product fire seals and openings left by services added after handover, across linear gaps at wall heads, service gaps in risers and joints between fire-resisting walls and floors. Whoever orders the work in Burford, the brief is typically the same: a clear scope, tidy work and joints that don’t fail again.
Around Burford, penetration and linear seals tend to be one-building jobs. With the specification and photos of the gaps, we can give a fixed quote and bring the right products.
Every job is signed off with a 12-month guarantee. The promise is simple: if our work fails within that year, we put it right.
- Where
- Burford (OX18)
- Wider area
- Oxfordshire
- Cover
- 12 months on every job
- Quote
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
What the job involves on each surface
Plastic pipes
Waste and drainage pipes through floors are a frequent case. Whether sealant alone is acceptable depends entirely on the tested detail, and we won’t substitute it for a specified collar.
Small ducts
We seal around ducts only within what the tested detail covers. Dampers and ductwork systems themselves are outside our work.
Common questions from Burford clients
Is Burford off your patch?
No. Places such as Burford are covered as much as the big towns. We cover Greater London and the counties of the South East. Where we can, we group nearby jobs to make the most of each trip.
What happens to BS 476 references for fire stopping in Burford?
References to BS 476 classes are being removed from Approved Document B from 2 September 2029, after which BS EN 13501-2 classification is the route, subject to transitional arrangements. Our part doesn’t change: the specified product, to its tested detail.
Will you just go over the old sealant?
No, never. Sealing over old material is one of the classic causes of early joint failure, so it all comes out first.
Do you hold CHAS accreditation?
Yes. CHAS accredited, Constructionline member, and our applicators hold CSCS cards.
Do you guarantee your work?
Yes, for 12 months. If our installation fails in that time, we return and fix it.
Will your applicators have CSCS cards?
Yes. Our applicators hold CSCS cards.
When can you be on site?
Give us your site hours and any access windows in your enquiry, and we’ll schedule the work to suit. You can reach the office between 8am and 5pm, Monday to Friday.
Honest limits
Our job is the joint, not everything around it. Sealant alone won’t deal with:
- Reviewing a building’s overall fire safety
- Walls or floors that aren’t fire-resisting to begin with
- Issuing fire ratings or certificates for seals
If in doubt, phone 01277 525 020 or email drawings and photos and we’ll say what we think before you book.
Joints and surfaces we work on
- Pipe penetrations
- Small duct penetrations where the tested detail allows
- Cable penetrations
- Joints between fire-resisting walls and floors
- Linear gaps at wall heads
- Service gaps in risers
What sets the cost
Quotes vary with the job. It mainly depends on:
- The total length or number of joints
- The site’s rules and procedures
- Any access equipment needed
- Specialist products, such as fire-rated or hygienic sealants
Access can matter as much as the joints themselves: joints within easy reach take less time than ones that need access equipment. Mention the access as part of your enquiry.
What to include in your enquiry
A few photographs plus some basic facts will normally do. Please tell us:
- Where the site is, with the postcode
- The asbestos register, for older buildings
- Access details, including height
- Drawings or a marked-up plan, if available
A handful of photographs and a postcode is the fastest way to a quote. Upload them with the quote form, or speak to us on 01277 525 020 or email a schedule or drawings to discuss it first.
Also in Burford
Leave it or put it right?
An open or wrongly sealed service penetration lets fire and smoke reach the next compartment much sooner than the building was designed for. While the openings can be reached, sealing them is normally straightforward. Wait until ceilings close or areas are occupied and the same work becomes harder to reach. Sealant hardens, cracks and loses grip with age, UV and movement. Replacing it before it fails keeps water out.
The work involved drives the cost: stripping out, preparation, sealing, access and phasing. Call for a quote.
Why clients in Burford choose us
- Fully insured
- Failed material removed, not covered up
- Health and safety: CHAS accredited
- Work to your specification and the manufacturer’s guidance
Take a look at what affects the cost or our accreditations and insurance.
Do you need fire stopping in Burford?
When a seal departs from its tested detail, the evidence no longer covers it. An oversized gap, too shallow a bead, missing backing or two makers’ products combined are what we find most often.
Most enquiries start with one or more of the following:
- Openings found when ceilings come down for a refit
- Damaged fire seals in risers and voids
- Fire-rated sealant that has cracked or shrunk back
- Openings left by services added after handover
Holiday works at schools like Burford Primary School often leave service openings to seal before pupils return.
Questions to ask before you book
- Whether old or failed sealant will be cut out, not overlaid
- What site paperwork they can supply
- Whether primer will be used where the manufacturer specifies it
- The terms of the workmanship guarantee
Compartment walls and floors in Burford
There are a good number of hotels within about 2 miles of Burford. A hotel refit often runs new services through compartment walls between bedrooms and corridors, and each opening needs the specified seal. For England, the fire stopping of penetrations is dealt with in Approved Document B. References to the older BS 476 classes are being removed from it from 2 September 2029, after which the European classification, BS EN 13501-2, is the route, subject to transitional arrangements. What we install is set by the specification, and it goes in to the tested detail.
For a building such as Church of St John the Baptist, new heating or data runs are the usual reason penetrations need sealing. In a hotel such as The Highway Hotel, which lies north-west of Burford, new pipework or cabling through bedroom and corridor walls needs sealing with the specified product.
Burford is about 3 miles north-west of Carterton, in Oxfordshire. Looking for fire stopping in Burford? We can help, as we do across Oxfordshire. Burford is one of 423 places we cover in Oxfordshire for service penetrations. We also cover Oxford, some 18 miles away.
We take on service penetrations across the OX18 postcode area, whatever the building. Buildings on High Street, Lower High Street and Swan Lane are within our area for service penetrations. Main routes into Burford include the A40 and A361. Sites close to Burford are covered too, including Fulbrook (1 mile north-east), Little Barrington (3 miles west), Milton-under-Wychwood (4 miles north), Fifield (4 miles north) and Idbury (5 miles north). Bigger towns within reach include Witney (6 miles east), Carterton (3 miles south-east), Faringdon (11 miles south), Kidlington (15 miles east), Chipping Norton (10 miles north) and Woodstock (13 miles east).
Local landmarks in Burford
In Burford, that means premises near Burford School and The Royal Oak Public House. The nearest railway station is Shipton station, about 4.5 miles north-east of the centre.