Bredgar fire stopping
Our CSCS-carded applicators take on fire-rated and intumescent sealing of service penetrations and linear gaps in Bredgar and the surrounding area. Send details for a fixed quote.
- Penetration schedules that need working through
- Improvised or mixed-product fire seals
- Builders’ foam or ordinary silicone in compartment walls
Fire stopping near Bredgar
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Honest limits
A few problems need another trade or a different fix, and we say so rather than covering them up:
- Approving the work on behalf of building control
- Deciding what a wall or floor needs, which belongs to the designer
- Fire risk assessments, a job for a competent assessor
If in doubt, ring 01277 525 020 or use the quote form and we’ll say what we think before you book.
Surfaces we seal
- Linear gaps at wall heads
- Small duct penetrations where the tested detail allows
- Service gaps in risers
- Pipe penetrations
- Joints between fire-resisting walls and floors
- Cable penetrations
Fire stopping in Bredgar, done properly
Fire-rated sealant suits many small service penetrations: copper and steel pipes, cables and some small ducts where the tested detail allows. Larger openings and some plastic pipes call for collars, wraps, batts or boards instead. We use sealant where it is the specified product, and we tell you when a detail calls for something else. If you have fire sealant pulled out of the opening and improvised or mixed-product fire seals, we can put it right, whatever the surface. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, the work in Bredgar is the same: failed joints cut out, faces prepared and the right sealant laid to the right depth.
Barn and farm-building conversions near places like Bredgar often combine new partitions with old walls. A penetration seal only performs as tested if product, substrate, service, gap and depth all match the detail.
Whoever the client is, the cover is the same: a 12-month guarantee on our workmanship. It doesn’t extend to damage, faults in the building or work by others, and we’re upfront about that.
- Where
- Bredgar (ME9)
- Wider area
- Kent
- Guarantee
- A 12-month guarantee
- Quote
- A fixed quote before we start
- Call
- 01277 525 020
- Updated
- 3 November 2026
Aftercare for building managers
Your facilities or cleaning team can help the joints last. Pass these on to them:
- Settle who seals which penetrations at the start of a project
- Brief every trade that openings they make must be sealed
- Keep general-purpose fillers away from compartment walls
- Keep product data and details in the fire safety file
New services after handover are a common way fire stopping gets breached. Building it into each contractor’s sign-off keeps the walls intact.
The simplest way to keep compartment walls intact is to plan fire stopping into every job that crosses them. Then the seal goes in while the area is open, not months later.
Diagnose, treat, sign off
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Joint faces are cleaned back to sound, dry surfaces, the manufacturer’s primer is applied where it’s called for, and the sealant is tooled off neatly. Smaller jobs around Bredgar can be grouped with others nearby, which keeps travel down. A fixed quote is given before anything starts.
- First we confirm the product and tested details named in the specification.
- Openings are measured and grouped by detail.
- Improvised fillers and failed sealant are removed.
- Mineral wool or other backing is fitted where required.
- Fire-rated or intumescent sealant goes in around the services and is tooled off.
- Completed areas are checked with you, with the records agreed when we quoted.
What we need from you
- Agree which areas must stay open
- Share the asbestos register for older buildings
- Share your working hours and any access restrictions
Request a quote
Photos, drawings or a schedule of the joints are often enough for a fixed quote. Where a site visit makes more sense, we will arrange one.
Related advice
Fire-rated sealing for Bredgar buildings
Bredgar is about 37 miles from central London. Business park offices in the commuter belt are refitted as tenants change, and each fit-out adds services through compartment walls. Fire stopping of openings and penetrations in England falls under Approved Document B. From 2 September 2029, BS 476 references are being taken out of Approved Document B, leaving BS EN 13501-2 classification as the route, subject to the Government’s transitional arrangements. Our part stays the same: the specified product, installed to its tested detail.
Large healthcare estates like Sittingbourne Memorial Hospital, 2.2 miles north-east of Bredgar, change their services often, so penetration seals are worth checking after M&E work. Older community buildings such as Church of St John the Baptist that have been rewired or given new heating can have service gaps through walls worth checking against the specification. For a building at a site such as Kent Science Park, 1.2 miles to the east of Bredgar, a check of penetration seals after each fit-out is good practice.
Bredgar is about 3 miles south-west of Sittingbourne, in Kent. We cover Bredgar, with the same fixed quotes and 12-month guarantee as everywhere else. We work across 931 places in Kent. London is covered too, around 37 miles from Bredgar.
Commercial sites across ME9 are covered for service penetrations. Buildings on The Street, Medlar Close and Primrose Lane are within our area. Just outside Bredgar, we also work in Silver Street (1 mile west), Oad Street (1 mile north-west), South Green (2 miles west), Danaway (2 miles north-west) and Chestnut Street (2 miles north). Bigger towns within reach include Maidstone (8 miles south-west), Ashford (14 miles south-east), Sittingbourne (3 miles north-east), Whitstable (15 miles east), Faversham (8 miles east) and Minster (9 miles north-east).
Near you in Bredgar
In Bredgar, that means premises near Westlands School and Cromers Wood, among other places. For rail, the closest station is Sittingbourne station, about 2.6 miles north-east of the centre. Well-known places in the area include Sittingbourne Heritage Museum (2.7 miles north-east) and Bayford Court (2.9 miles north-east). The countryside around Bredgar includes Detling Hill.
Common questions from Bredgar clients
What does the BS 476 change mean for fire-rated sealant in Bredgar?
Approved Document B loses its BS 476 references from 2 September 2029, and BS EN 13501-2 becomes the route, subject to transitional arrangements. The designer or fire engineer sets the specification, and we install the product to the manufacturer’s tested detail.
Can you work at a site such as Kent Science Park, by Bredgar?
Yes. Our area takes in Bredgar and its surroundings, with estates and business parks such as Kent Science Park included. A few photos and the unit address let us price the work.
Will you come and look before quoting?
It depends on the job. Straightforward work can often be priced from photos and measurements, while larger or less clear jobs get a site visit first.
Do you take on small jobs?
Small jobs are welcome alongside larger packages. Send details for a fixed quote.
Do you have public liability insurance?
Yes. We’re fully insured, including public liability cover.
When can the area be used after sealing?
The product and site conditions decide that. Some products skin over quickly but need longer to cure fully, and we confirm it before leaving site.
When is resealing likely to be due?
It depends on movement, UV and weather, cleaning, traffic and the product. Treat them as maintenance items and inspect them regularly.
What the job involves on each surface
Cables and cable bundles
Single cables and small bundles are often within a fire-rated sealant’s tested detail. The detail limits bundle size and the gaps between and around cables and we work within those limits.
Small ducts
Some fire-rated sealant details cover small ducts. Bigger ducts and fire-resisting ductwork are normally handled with other products.
For managing agents and facilities managers
Blocks and communal areas make up much of the work for housing associations and agents. Work can be phased so residents and staff keep access throughout, and each stage is agreed with your contact.
For main contractors, we work as the sealant subcontractor on new-build and refurbishment projects. Programme, specification and site rules come first, and our applicators hold CSCS cards.
Other services in Bredgar
General trades versus a specialist
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and we will confirm the paperwork you need with the quote.
Some joints are best left to specialists: for example fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. A poor seal in places like these tends to cost more to put right later.