Expansion joint sealing in Timsgarry
Need expansion joint sealing in Timsgarry? It’s simple: send details, get a quote, we seal, guaranteed.
- Damp inside where a wall movement joint has failed
- Chipped joint edges on forklift routes
- Leaks through car park deck joints onto the level below
Expansion joint sealing in Timsgarry
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Questions about Timsgarry
Can you take on a job in Timsgarry, on the island?
Yes. Every Scottish council area is within our area, and that includes island locations such as Timsgarry. Island work is planned around ferry crossings and the weather, so photos and a full list before we travel are essential.
Our building in Timsgarry is near the coast: does that change the sealant?
It can. Wind-driven rain and, closer to the shore, salt air are harder on external joints. That puts more weight on product choice, primers where the manufacturer specifies them, and correct joint sizing.
Is it fine to apply new sealant on top of old?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, since fresh sealant will not bond reliably to aged material.
Do you hold CHAS accreditation?
Yes. We are CHAS accredited and a Constructionline member.
Can weather delay the job?
It can, for external work. Wet joints and cold, damp or frosty conditions stop the sealant bonding properly, so we watch the forecast and rearrange outside work if we have to. Internal work is far less affected.
What guarantee do you give on joint sealing?
Our workmanship on movement joints carries a 12-month guarantee. The guarantee covers how we sealed, not damage caused afterwards.
Will your applicators have CSCS cards?
Yes. If you need card details for site access, let us know and we’ll send them with the quote.
About our expansion joint sealing in Timsgarry
Our movement joint work takes in walls, panels, decks and floors: brickwork and blockwork joints, precast and cladding panel joints, concrete joints, car park decks and ramps, podiums and floor movement joints. The product depends on the movement, the weather and anything that runs over it, and we’ll confirm the choice in the quote. If you have chipped joint edges on forklift routes and sealant peeling off one face of the joint, we can help. Sealant applicators who only do sealant are a different proposition from a general trade with a gun in the van: in Timsgarry, that means joint design, primers and backing rod as standard.
In smaller places such as Timsgarry, the joints we are asked about sit in workshops, farm sheds, schools and halls. Slabs and yards take vehicles, rain and frost.
Work we carry out in Na h-Eileanan Siar comes with a 12-month guarantee. Should something we installed fail, ring 01277 525 020 or email a schedule or drawings and we will come back to it.
- Location
- Timsgarry (HS2)
- Region
- Na h-Eileanan Siar
- Guarantee
- A 12-month guarantee
- Price
- A fixed quote before we start
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
What sealant work can’t fix
We check first that sealant really is the fix. It isn’t the answer for:
- Failed waterproofing membranes on podiums, roofs or decks (a waterproofing specialist’s job)
- Crumbling edges that would give a new bead nothing sound to grip
- Structural movement beyond what the joints were designed for (that needs a structural engineer)
If you’re not sure, just speak to us on 01277 525 020 or send photos by email and we’ll give you a straight answer before you book.
Where we work in Timsgarry
- Car park decks and ramps
- Blockwork control joints
- Cladding panel joints
- Brickwork movement joints
- Podiums and floor movement joints
- Precast concrete panel joints
Slabs, ramps and loading bays in Timsgarry
With the shore within about 1 mile, Timsgarry counts as a coastal location. Near the sea, external slabs, ramps and decks see salt air and driven rain as well as their usual loads, so it pays to keep them sealed. Being on an island, Timsgarry means planning around ferry times as well as the weather. Photos and joint sizes help us load the right products.
For an occupier at a site such as Erista Industrial Estate, which lies north-east of Timsgarry, the joints at loading doors and dock levellers typically see the hardest wear.
Timsgarry (Gaelic: Timsgearraidh) is in Na h-Eileanan Siar. Businesses, contractors and managing agents in Timsgarry can call on us for movement joints. Timsgarry is one of 87 places we cover in Na h-Eileanan Siar.
Commercial sites across HS2 are covered. Just outside Timsgarry, we also work in Breasclete (10 miles east), Na Gearrannan (11 miles north-east), Carloway (11 miles north-east), Shawbost (14 miles north-east) and Baile Ailein (17 miles south-east). For island and remote sites, we plan travel and materials carefully, so include the location in your enquiry.
Near you in Timsgarry
A little further out are Uig Heritage Centre (less than half a mile north-east). Not far away are Suainaval and Loch Suainaval.
Why it’s worth doing now in Timsgarry
A failed joint seal doesn’t mean the slab, panel or wall needs replacing. If the material either side is sound, a properly prepared reseal restores the joint. We will flag where edges need repair before sealing. Buildings that aren’t in daily use, such as halls and seasonal premises, may let water in unnoticed, so a failed joint has time to cause damage. Resealing early avoids that.
The product called for affects the cost, and so does the preparation, from cutting out to priming and backing rod. Access, phasing and site requirements come into it too.
Why us?
- Colour agreed before work starts
- Fully insured
- Joints cleaned back to sound surfaces
- A fixed quote before work starts
Read what affects the cost and our accreditations.
On site: what to expect
We follow your site rules from the start: sign-in, induction and whatever permit system the building uses. Once we are cleared to begin, the joints are worked through in the order agreed with your site contact. For work around Timsgarry, we aim for one trip, which is why we ask for photos and a full list first. Outside work also needs a suitable weather window.
- First, the joints are inspected for width, movement and the type of failure.
- Next, we fix a price and confirm the sealant we propose for the movement.
- The failed seal is removed and both faces are cleaned until sound and dry, and we tell you if any edges need repairing first.
- We control the depth with backing rod or, in shallow joints, bond-breaker tape.
- After any primer the maker requires, the bead is applied and tooled so it grips two sides only.
- We check every joint before sign-off, and the work carries our 12-month guarantee.
What we need from you
- Share the asbestos register for older buildings
- Explain the parking and delivery arrangements
- Let building users know which areas are affected
Request a quote
Every quote starts with the facts: the joints involved, quantities, access and the product called for. Share whatever details you have and we will fill any gaps with a visit.
Read more
Nearby places to Timsgarry
What else we do in Timsgarry
What affects the price in Timsgarry
Sealant work doesn’t have a standard rate, because every site is different. What we take into account:
- Location, for remote and island sites
- The total length or number of joints
- The product specified
- Joint width, depth and condition
Whether it’s a single area or a whole estate, the same things set the price: scope, access, product and programme. Call for a quote and we will put a fixed figure on it.
Details that help us quote
We can often quote from photos and a few details. Please tell us:
- What the building is and how it’s used
- When you need the work done
- Where the site is, with the postcode
- Rough lengths or quantities, or drawings if you have them
A handful of photographs and a postcode is the fastest way to a quote. Send them through the quote form, or give us a call on 01277 525 020 or send photos by email if you’d rather talk the job through.
Common problems we fix in Timsgarry
Repeated failure often traces back to the wrong product. Products not classed for the movement fail early. Movement capability is set out in BS EN ISO 11600.
Common reasons buildings call us in:
- Water dripping through deck or ramp joints
- Debris jammed in movement joints
- Expansion joints split through the centre of the bead
- Previous reseals laid over old sealant
Around Timsgarry, each joint gets a filler or sealant matched to what crosses it and how much it moves.
What your quote should include
- The terms of the workmanship guarantee
- Who will actually carry out the work
- Whether primer will be used where the manufacturer specifies it
- Their pre-qualification and accreditations
Aftercare for building managers
For the best life from the joints:
- Include every elevation and deck joint in periodic inspections
- Note which joints were done, when, and with what
- Check joints after long freezing spells
- Keep racking legs and heavy point loads off floor joints
Grit is the slow enemy of a joint seal. Stones pressed into the bead by wheels or feet can puncture it and decks and floors suffer most. A routine sweep is the simplest protection.
On a multi-storey car park, a failed joint usually shows up as a leak onto the deck underneath. Salty water dripping through stains soffits and lands on parked vehicles. Resealing early limits the damage.