Expansion and movement joint sealing in Temple Hill, Kent
Our CSCS-carded applicators take on expansion and movement joint sealing in walls, decks and floors in Temple Hill. Send details for a fixed quote.
- Sealant peeling off one face of the joint
- Spalled or broken joint edges in floors and decks
- Car park joints leaking onto vehicles below
Expansion joint sealing near Temple Hill
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
Maintenance after handover
To get the most from the new sealant:
- Keep racking legs and heavy point loads off floor joints
- Sweep decks, ramps and floors so grit doesn’t collect in the joints
- Include every elevation and deck joint in periodic inspections
- Leave barriers in place until fresh joint sealant has cured
Debris does more harm to joint sealant than most people realise. Stones pressed into the bead by wheels or feet can puncture it. Regular sweeping keeps joint lines clear.
Unsupported floor joint edges spall under forklift and pallet-truck wheels. Damaged edges make the floor rough and wear wheels faster. Sealing early protects the edges.
How we handle expansion joint sealing in Temple Hill
For movement joints in Temple Hill, photos and approximate lengths are the best start. Send them through our quote form, and we will arrange a site visit if needed. To discuss the joints first, ring 01277 525 020 or send details through our quote form. We work on podiums and floor movement joints, cladding panel joints and brickwork movement joints, and the failures we are asked to look at most are joints where the bead has lost adhesion and chipped joint edges on forklift routes. Facilities teams, main contractors and managing agents in Temple Hill tend to want the same three things: a clear scope, tidy work and joints that don’t fail again.
Around Temple Hill, most floor and movement joint jobs are single buildings or yards. That way the right materials come on the day and the job is done in one visit where possible.
Every job we finish is backed by a 12-month workmanship guarantee. If our installation lets you down in that time, we return and fix it.
- Location
- Temple Hill (DA1, DA2, DA5)
- Region
- Kent
- Guarantee
- 12 months on our workmanship
- Quote
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
Places near Temple Hill
Also in Temple Hill
Your questions answered
Is Temple Hill too far out for you?
No. Places such as Temple Hill are covered as much as the big towns. We cover Greater London and the counties of the South East. Where we can, we group nearby jobs to make the most of each trip.
Can you work at a site such as Riverside Industrial Estate, by Temple Hill?
Yes. Estates, retail parks and business parks around Temple Hill, Riverside Industrial Estate among them, are all within reach. To start, just give us a call on 01277 525 020 or email the details over with the unit, the joints involved and your access times.
How long does movement joint sealing take?
The metres of joint, the access and the amount of removal decide it. Typically it takes anything from part of a day to a couple of weeks, depending on joint lengths, widths and access.
What hours do you work?
Give us your site hours and any access windows in your enquiry, and we’ll plan around them. Our office runs Monday to Friday, 8am until 5pm.
Can a joint be sealed if the edges are broken?
Sound edges are essential. Where they’ve broken up, we’ll tell you they need repairing first.
Are your applicators CSCS-carded?
Yes. If you need card details for site access, let us know and we’ll send them with the quote.
What sealant do you use in movement joints?
Whatever suits the joint and the specification. We name the proposed product in the quote so there are no surprises.
How a job runs
We follow your site rules from the start: signing in, inductions and any permit to work. With the paperwork done, the joints are worked through in the order agreed with your site contact. What matters most for a job in Temple Hill is a clear list of what needs doing, so send photos of each area. A fixed quote follows.
- Photos, joint lengths and drawings come to us, or we visit.
- Joint widths and expected movement are checked against what the sealant can take, and flag anything that needs an engineer.
- Old sealant and debris are cut out of every joint.
- Any broken arrises or friable edges are flagged before work goes further.
- A sealant suited to the movement and traffic is laid to depth and tooled.
- Areas reopen once cured, and the work carries our 12-month guarantee.
Preparing the site
- Agree which areas must stay open
- Arrange parking or a loading space
- Flag any permit to work we’ll need
Request a quote
For a fixed quote, give us a call on 01277 525 020 or send photos by email, telling us the site location and the nature of the job. Our quote form is another easy route.
Advice
Cost factors for movement joints
Each job is priced on its own details. The things that drive the figure:
- Phasing around occupants
- Backing rod, priming and other preparation
- Removal of failed or old sealant
- The site’s rules and procedures
Cost follows what’s involved: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a fixed quote and we’ll explain how it’s made up.
Before you send an enquiry
Whether it’s one area or a whole building, these details speed things up:
- Clear photographs of the problem areas
- Any specification or named product
- Whether an asbestos survey exists
- Where the site is, with the postcode
Let us know the site, the scope and your timescale, and a fixed quote will follow. The easiest way is to speak to us on 01277 525 020 or email drawings and photos.
Warehouse floors and decks around Temple Hill
Central London is about 14 miles from Temple Hill. Warehousing clusters around the motorways that ring and radiate from London. The 3 miles around Temple Hill take in at least three named trading estates, business parks or retail parks. That puts plenty of warehouse floors, service yards and car parks close by, all with joints under traffic.
Campuses like University of Greenwich, 1.9 miles east of Temple Hill, mix old and new buildings, with movement joints wherever they meet. A healthcare site such as Little Brook Hospital, 0.8 miles east of Temple Hill, depends on car parks, ramps and service yards whose joints take traffic all day. If you manage units on an estate such as Riverside Industrial Estate, which lies north-west of Temple Hill, the floor joints under forklifts and pallet trucks and the slab joints in the yard are the ones to watch.
Temple Hill is about 1 mile north of Dartford, in Kent. Looking for expansion joint sealing in Temple Hill? We can help, as we do across Kent. 931 places across Kent fall within our area, Temple Hill among them. There’s a separate page for London, about 14 miles away.
Postcode districts covered here: DA1, DA2 and DA5. Streets here include Kent Road, Keyes Road and Bayly Road, and sites on any of them can send details for a fixed quote. You will find Temple Hill on or near the A226. Nearby places we also cover include Dartford (1 mile south), Hawley (2 miles south), Stone (2 miles east), Darenth (2 miles south-east) and Greenhithe (2 miles east) for movement joints. Further afield, our area takes in Sevenoaks (12 miles south), Gravesend (7 miles east), Northfleet (5 miles east), Swanley (4 miles south-west), Kings Hill (15 miles south-east) and Swanscombe (3 miles east).
Near you in Temple Hill
We work on buildings around Central Park, The Leigh UTC and Stone Lodge School, among other places. There’s a railway station in Temple Hill itself: Dartford station. Nearby you will also find Stone Castle (2.3 miles east) and Bluewater (2.1 miles east). Open spaces near Temple Hill include Wansunt Pit and Sawyers Lake.
Commercial clients in Temple Hill
If you look after buildings for someone else, clear figures and clear communication matter. You get a fixed quote, an agreed scope and a walk round at the end, plus a 12-month guarantee.
Main contractors use us as their sealant subcontractor, on new build and refurbishment alike. We work to your programme, your specification and your site rules.
How the job changes by surface
Brickwork and blockwork joints
Vertical movement joints in brick and block walls let the masonry grow and shrink. We use a sealant rated for the movement, usually low-modulus laid over backing rod at the correct depth.
Cladding panel joints
Metal and composite panels shift considerably as temperatures change. A sealant with the right movement class is chosen, and we will confirm the colours available for the specified product.
General trades versus a specialist
A short, simple internal joint is often within reach of a maintenance team. Where it goes wrong is preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
There’s also the paperwork. Main contractors and clients often ask for CSCS cards, RAMS and insurance details, and our CSCS-carded applicators are used to working under those rules.