Ruisgarry expansion joint sealing
Work needed on a movement joint in Ruisgarry? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Chipped joint edges on forklift routes
- Water dripping through deck or ramp joints
- New sealant over old, now failing
Expansion joint sealing in Ruisgarry
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Expansion joint sealing in Ruisgarry, done properly
Brickwork and blockwork walls have vertical movement joints at intervals that most people only notice when the sealant has gone. Once the seal fails, rain reaches the cavity and the joint can no longer close. The old seal comes out, backing goes in and a sealant with the right movement class is applied, primed where the manufacturer specifies. We work on car park decks and ramps, cladding panel joints and podiums and floor movement joints, and the usual reasons a site gets in touch are car park joints leaking onto vehicles below and rain penetration at brick or block movement joints. Whoever orders the work in Ruisgarry, the brief is normally the same: a fixed quote, no surprises on site and a 12-month guarantee behind the result.
Around smaller Scottish places like Ruisgarry, slabs needing attention are often in agricultural buildings, workshops, schools and hotels. Slabs and yards take vehicles, rain and frost.
A 12-month guarantee applies to all our work in Na h-Eileanan Siar. Should something we installed fail, call the office on 01277 525 020 or email us and we’ll come back to it.
- Where
- Ruisgarry (HS6)
- Wider area
- Na h-Eileanan Siar
- Guarantee
- 12 months on our workmanship
- Price
- Fixed quote, scope in writing
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
Keeping the joints sound
Your facilities or cleaning team can help the joints last. Pass these on to them:
- Check joints after long freezing spells
- Brief car park operatives to protect joint lines during winter clearance
- Sweep decks, ramps and floors so grit doesn’t collect in the joints
- Record the sealant used and the date in the O&M file
Keep wheels, feet and water off new joints until the sealant has cured. How long that takes depends on the product, the temperature and the depth of the joint, and we confirm it for each area before we leave. Barriers left in place until then protect the finish.
On a multi-storey car park, a failed joint normally shows up as a leak onto the deck underneath. That water often carries de-icing salts with it. Resealing early limits the damage.
Nearby places to Ruisgarry
Other services in Ruisgarry
Surface by surface
Brickwork and blockwork joints
Masonry faces are often porous, dusty or crumbly. Faces are prepared and primed wherever the sealant maker calls for it, then seal and tool the joint.
Joints between different materials
Different materials meeting at a joint rarely move in step. The product must bond to both substrates and cope with the movement, with primer where specified.
When something else is needed
Not every problem is a sealant problem, and we’re upfront when that’s the case. It won’t fix:
- Structural movement beyond what the joints were designed for (that needs a structural engineer)
- Mechanical expansion joint covers, cover plates or proprietary joint systems (a specialist supplier’s job)
- Concrete or masonry repairs along the arrises
Not sure which it is? You can call the office on 01277 525 020 or email the details over and we will tell you honestly.
What we seal
- Car park decks and ramps
- Cladding panel joints
- Podiums and floor movement joints
- Brickwork movement joints
- Blockwork control joints
- Precast concrete panel joints
Questions we are asked in Ruisgarry
Do we have to stop operations in Ruisgarry while the joints are sealed?
Rarely. Work is phased around your operations. Tell us which hours and entrances we can use and we will plan from there.
Does the sea air around Ruisgarry change the choice of sealant?
It can. Driven rain and salt are tougher on outside sealant than sheltered inland conditions. Product choice and preparation matter more, and sea-facing elevations are worth inspecting more often.
Can you seal joints in cold or wet weather?
Sealing onto a damp surface leads to adhesion failure so we’d rather rearrange than seal in the rain. We agree a revised date with you.
How do you deal with asbestos in old sealant?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and if asbestos is suspected, work stops until it’s tested. Removing asbestos is a job for asbestos specialists, not us.
Can weather delay the job?
For external joints, yes. The joint has to be dry and within the product’s temperature range, so frost, rain or cold mornings can delay outside work. Inside work is seldom held up.
Will your applicators have CSCS cards?
Yes. Our applicators hold CSCS cards, as many construction sites ask for.
Can the building stay open while you work?
Typically, yes. Phased work can be planned so areas stay in use.
When to call us in Ruisgarry
Sometimes the sealant holds but the substrate breaks away. If the edge of the joint is friable, the bond fails with it.
Site and facilities staff are often the first to spot these:
- Water dripping through deck or ramp joints
- Previous reseals laid over old sealant
- Damp inside where a wall movement joint has failed
- Chipped joint edges on forklift routes
For floors and slabs around Ruisgarry, the product is chosen for the traffic and the movement at each joint.
Questions to ask before you book
- What site paperwork they can supply
- Whether their applicators hold CSCS cards
- Their approach to joint depth and backing
- What level of public liability insurance do they hold?
Cost factors for movement joints
To price the job, we consider:
- The product specified
- How much there is to seal
- Backing rod, priming and other preparation
- Distance, for remote addresses
Cost follows what’s involved: stripping out, preparation, sealing, access and phasing. Call for a quote and we will explain how it’s made up.
Before you send an enquiry
It doesn’t need to be a full survey. These details are enough to start:
- Whether the building will be occupied during the work
- The asbestos register, for older buildings
- Clear photos of the problem areas
- Any specification or named product
A handful of photographs and a postcode is the fastest way to a quote. Send them through the quote form, or ring 01277 525 020 or email drawings and photos if you’d rather talk the job through.
Diagnose, treat, sign off
Before we leave any area, we remove the tape, clean down and inspect every joint with your site contact. Where the sealant needs time to cure before use, we tell you and sign the area. Jobs near Ruisgarry are often grouped with others in the same area, to make the most of each trip. Tell us how flexible your dates are.
- We start with photographs, approximate lengths and any drawings, visiting where needed.
- We compare each joint’s width with the movement and the sealant’s capability and tell you if the design looks wrong for the movement.
- Old sealant and debris are cut out of every joint.
- Edges are checked, and we tell you if any need repairing before sealing.
- A sealant suited to the movement and traffic is laid to depth and tooled.
- Areas reopen once cured, and the work carries our 12-month guarantee.
Getting the site ready
- Warn occupants and staff about the work
- Send asbestos survey details if the building is pre-2000
- Send your site hours and access windows
Getting a fixed quote
Specifications, drawings and tender packages are welcome with any enquiry, and we’ll price the work to it. Smaller jobs need nothing more than photographs and a few notes.
Advice
Expansion joint sealing in Ruisgarry: the local picture
Ruisgarry sits close to the coast, within about 1 mile. External movement joints in car parks, ramps and yards near the coast take salt and wind-driven rain on top of traffic, so it pays to keep them sealed. Ruisgarry is in the west of Scotland, the wetter side of the country. Open joints in external slabs take a lot of water. Dry spells are used for the external joints.
A joint near Ruisgarry that has lost its sealant lets in water and grit, and the edges suffer next.
Ruisgarry (Gaelic: Ruisigearraidh) is in Na h-Eileanan Siar. Anywhere in HS6, the process is the same: send details, get a fixed quote, we seal, and the work is guaranteed. Across Na h-Eileanan Siar, 87 places are covered, Ruisgarry among them.
Postcode districts covered here: HS6. Close to Ruisgarry, our area also takes in Clachan Shannda (4 miles south-west), Leverburgh (6 miles north-east), An t-Ob (7 miles north-east), Lochmaddy (8 miles south) and Locheport (12 miles south). Island and remote sites need extra planning, with travel, ferry crossings where needed and weather to allow for, so mention the location when you speak to us on 01277 525 020 or email drawings and photos.
What’s near Ruisgarry
For a walk, there’s Little Loch Borve and Borve Hill.