Peene expansion joint sealing
Work needed on a movement joint in Peene? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Expansion joints filled with dirt and stones
- Spalled or broken joint edges in floors and decks
- Sealant peeling off one face of the joint
Expansion joint sealing for Peene sites
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
Expansion joint sealing in Peene, done properly
Long runs of brick or block have movement joints built in. Failed sealant here lets rain into the wall and can leave the joint full of debris. The old seal is cut away, backing rod goes in at depth, and a low-modulus masonry sealant is gunned and tooled. We work on brickwork movement joints, cladding panel joints and podiums and floor movement joints, and what we are called in for most is water dripping through deck or ramp joints and joints where the bead has lost adhesion. Whether you call it commercial sealant work, mastic application or joint sealing, the work in Peene is the same: failed joints cut out, faces prepared and the right sealant laid to the right depth.
In and around smaller places like Peene, the concrete floors we see are often in converted farm buildings, small workshops and storage units. Joints in those slabs take vehicles, trolleys and foot traffic, and need a filler or sealant to match.
A 12-month guarantee applies to all our work in Kent. If an installation problem shows up, call the office on 01277 525 020 or send photos by email and we will arrange a return visit.
- Where
- Peene (CT18)
- Region
- Kent
- Cover
- 12 months on our workmanship
- Quote
- Quoted before any work starts
- Telephone
- 01277 525 020
- Updated
- 3 November 2026
What affects the price in Peene
The price varies from site to site. It mainly depends on:
- Quantities, in metres or numbers
- Removal of failed or old sealant
- Joint width, depth and condition
- Distance, for remote addresses
The price depends on the quantity of joints, what has to come out first and how the joints are reached. Call for a fixed quote when you’re ready.
Before you send an enquiry
For an accurate fixed quote, we need to understand the site. Send us:
- The postcode of the building
- How the joints are reached, and at what height
- Rough lengths or quantities, or drawings if you have them
- When you need the work done
Quotes are fixed against the scope you send, so the cost is agreed before work starts. To start the process, give us a call on 01277 525 020 or use the quote form.
What else we do in Peene
FAQs: Peene
Can being near the sea in Peene affect the sealant we need?
It can. Wind-driven rain and, closer to the shore, salt air are harder on external joints. That puts more weight on product choice, primers where the manufacturer specifies them, and correct joint sizing.
Can you work at a site such as Shearway Business Park, by Peene?
Yes. We cover Peene and the area around it, including industrial estates, business parks and retail parks such as Shearway Business Park. To start, just speak to us on 01277 525 020 or send photos by email with the unit, the joints involved and your access times.
How do I request a quote?
The quote form is the simplest route, though you can also call 01277 525 020 or email the details over. Include photographs or drawings if you have them.
Why has the sealant in our expansion joints split?
It depends on how the sealant has let go: tearing down the centre means too much movement, and lifting off one side means poor adhesion. Sometimes the edge material itself has failed.
What guarantee do you give on joint sealing?
Our workmanship on movement joints carries a 12-month guarantee. The guarantee covers how we sealed, not damage caused afterwards.
Do you have public liability insurance?
Yes. We are fully insured, including public liability cover.
How do you deal with asbestos in old sealant?
Managing asbestos is the dutyholder’s responsibility, so for older buildings we ask for the asbestos register first. Work pauses if suspect material is found, until it has been tested.
Maintenance after handover
Your facilities or cleaning team can help the joints last. Share these points with them:
- Keep product details with the building records for the next reseal
- Put movement joints on the planned maintenance inspection round
- Sweep decks, ramps and floors so grit doesn’t collect in the joints
- Keep scrapers and ploughs from dragging across joint sealant
Grit is the slow enemy of a joint seal. Grit trodden or driven into the joint works at the surface until it tears. Regular sweeping keeps joint lines clear.
Rain gets into walls through torn brick and block movement joints. The first sign is often a damp patch indoors. Resealing promptly prevents internal damage.
Signs you need expansion joint sealing in Peene
Some joints were never sealed with the right product. Products not classed for the movement fail early. BS EN ISO 11600 classifies building sealants by movement capability.
Site and facilities staff are often the first to spot these:
- Expansion joints filled with dirt and stones
- Expansion joints split through the centre of the bead
- Damp inside where a wall movement joint has failed
- Water dripping through deck or ramp joints
For a centre such as Golden Valley Shopping Centre, 1.6 miles to the south-east of Peene, the service yard and car park joints normally need attention first.
Comparing quotes
- Whether primer will be used where the manufacturer specifies it
- Will failed sealant be removed rather than covered?
- Will RAMS and insurance details be available?
- Health and safety accreditation such as CHAS
Diagnose, treat, sign off
Our CSCS-carded applicators arrive with the sealants, primers and backing rod the job calls for. Any old material is cut back to clean, sound faces, primer goes on where the manufacturer specifies it, and each bead is tooled to a neat concave finish. Smaller jobs around Peene can be grouped with others nearby. You’ll have a fixed quote before work starts.
- The first job is to check each joint: how wide it is, how it moves and why the old seal let go.
- A fixed quote follows, naming the sealant and its movement class.
- Old sealant and filler are cut out and the joint faces cleaned back to sound material, and we tell you if any edges need repairing first.
- Closed-cell backing rod is set to depth, or bond-breaker tape in shallow joints.
- Primer goes on where the manufacturer specifies it, followed by the sealant, which is then tooled off.
- We check every joint before sign-off, and the work carries our 12-month guarantee.
What we need from you
- Send asbestos survey details if the building is pre-2000
- Point out any areas we must not close
- Move anything stored against the joints
Quotes
A good quote starts with a clear picture: the joints involved, quantities, access and the product called for. Share whatever details you have and we will fill any gaps with a visit.
Related advice
What the job involves on each surface
Concrete and precast panel joints
Precast and concrete panel joints move daily. We use a sealant classed for the movement, laid over backing to depth.
Brickwork and blockwork joints
Vertical movement joints in brick and block walls let the masonry grow and shrink. They take a low-modulus sealant with a movement class to suit laid over backing rod at the correct depth.
Why deal with it now?
Spot repairs can be useful on a tight budget. The remaining sealant is often close to failing too, and a second visit means paying for access again. We can price a patch and a full reseal side by side. Older rural buildings around Peene move with the seasons, and rigid or tired sealant can’t keep up. A sealant with the right movement capability, correctly sized, lasts far better.
The work involved drives the cost: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a quote and we will explain how it’s made up.
What you get with us
- CHAS accredited contractor
- Standard and matched colours in many product ranges
- One contact handling all your sites
- Constructionline member
Where floor joints take the most wear near Peene
Peene sits close to the coast, within about 2 miles. Open joints in coastal car parks and yards let in salt-laden water as well as grit, and edges left open tend to break up faster. Less than 3 miles from Peene there are at least three named estates and business parks. Sites like these are full of saw-cut floor joints, yard slabs and car park joints.
On a site such as Shearway Business Park, which lies east of Peene, the movement joints are in car park slabs, paving and building elevations. A campus such as University Centre Folkestone, 2.9 miles to the south-east of Peene, has long runs of movement joint in its buildings, decks and paving.
Peene is about 2 miles north-west of Folkestone, in Kent. Commercial clients in Peene use us for work on movement joints. We work across 931 places in Kent, from busy centres to rural villages. Our Brighton page has more on work in that area, about 57 miles away.
Business premises anywhere in CT18 are within our area for movement joints. If your building is just outside Peene, we cover Newington (1 mile south-west), Arpinge (1 mile north-east), Cheriton (1 mile south-east), Etchinghill (1 mile north-west) and Seabrook (2 miles south). Further afield, our area takes in Ashford (11 miles west), Canterbury (13 miles north), Dover (8 miles east), Deal (14 miles north-east), Hythe (3 miles south-west) and Tower Hamlets (8 miles east).
Near you in Peene
The closest station to Peene is Folkestone West station, about 1.8 miles south-east. Well-known places in the area include Elham Valley Countryside Centre And Railway Museum (less than half a mile west) and Folkestone Castle (1.8 miles east). For a walk, there’s Cheriton Hill.