Expansion and movement joint sealing in Kent Street, Kent
Expansion and movement joint sealing in walls, decks and floors throughout Kent Street and nearby, by CSCS-carded applicators. Fully insured and CHAS accredited.
- Water getting into the wall through a failed joint
- Weathered movement joint sealant that no longer flexes
- New sealant over old, now failing
Expansion joint sealing for businesses in Kent Street
Tell us what needs sealing and where, with photos or drawings if you have them, and we’ll price it.
About our expansion joint sealing in Kent Street
Width, depth and product all have to work together. Joint width must suit the movement and the movement class of the sealant while depth is limited by backing rod or, in shallow joints, a bond-breaker. For wider joints, the width-to-depth ratio is often around 2:1, as the manufacturer advises. The enquiries we see most involve previous reseals laid over old sealant and chipped joint edges on forklift routes, on car park decks and ramps, blockwork control joints and brickwork movement joints. Whoever orders the work in Kent Street, the brief is typically the same: a clear scope, tidy work and joints that don’t fail again.
For a site near Kent Street, measurements and photos up front mean one trip where possible, with the right materials on hand. Tell us the joint widths if you can, and what drives or walks over them.
We stand by our work with a 12-month guarantee. It covers how we prepared and applied the sealant.
- Location
- Kent Street (ME18)
- Region
- Kent
- Guarantee
- 12 months on every job
- Price
- Fixed quote, scope in writing
- Phone
- 01277 525 020
- Page updated
- 3 November 2026
When something else is needed
Not every problem is a sealant problem, and we are upfront when that’s the case. It won’t fix:
- Movement on a scale no sealant is meant to absorb
- Leaks coming from the membrane rather than the joint seal
- Concrete or masonry repairs along the arrises
Not sure which it is? You can call the office on 01277 525 020 or send photos by email and we’ll tell you honestly.
Surfaces we seal
- Blockwork control joints
- Precast concrete panel joints
- Car park decks and ramps
- Podiums and floor movement joints
- Brickwork movement joints
- Cladding panel joints
Why act early in Kent Street
Leaving a failed movement joint rarely stays a small problem. Grit and water fill the gap and the material either side breaks up and the job grows to repairs as well as sealing. Acting at the first split keeps the cost down. Converted and older buildings near places like Kent Street tend to move, and aged sealant cracks. The right product, sized to the joint, copes much better.
The specified product makes a difference, as does the preparation each joint needs, from cutting out to priming and backing rod. Access, phasing and site rules also count.
Why clients in Kent Street choose us
- Clear, fixed quotes
- Matching to RAL references, product permitting
- Fully insured
- Constructionline member
Read our cost guide or our accreditations.
FAQs: Kent Street
Is Kent Street too small for you to travel to?
Not at all: smaller places are covered as well as towns. London and every South East county are within our area. Where we can, we group nearby jobs to make the most of each trip.
Can you work on a hospital site such as Maidstone Hospital?
Yes, provided the work is planned with the site’s estates team. Each area is agreed with the ward or department and the estates team in advance.
How long will the new sealant last?
There isn’t a single answer, since movement, weather, cleaning and use all affect it. Regular checks let you plan resealing before leaks or damage.
When can the area be used after sealing?
Curing time varies by product, and we confirm it on the day, and sign any area that should be left alone.
Why has the sealant in our expansion joints split?
Typically the joint is moving more than the sealant can take. We review the joint design as well as the sealant before pricing so the same failure isn’t repeated.
Can you work on car park ramps and decks?
Yes, we do. Tyre loads, grit and de-icing salts make these some of the hardest joints to keep sealed, and we will tell you if any edges need repairing first.
What if there’s asbestos in the old mastic?
Asbestos is possible in some older mastics, particularly in buildings from before 2000. Before we disturb old sealant in an older building, we ask to see the asbestos register or survey, and work stops until any suspect material has been tested. We don’t remove asbestos-containing materials.
Also near Kent Street
Other services in Kent Street
Maintenance after handover
Your facilities or cleaning team can help the joints last. Share these points with them:
- Treat a small split as a warning, not a cosmetic issue
- Keep scrapers and ploughs from dragging across joint sealant
- Keep traffic off new joints until the cure time is up
- Record the sealant used and the date in the O&M file
Fresh joint sealant needs its full cure time before it takes traffic or water. The time varies with product, conditions and joint depth and we will tell you when each bay or area can reopen. Keeping the area coned off until then avoids tyre marks and damage.
Unsupported floor joint edges spall under forklift and pallet-truck wheels. Damaged edges make the floor rough and wear wheels faster, and the damage spreads along the joint. Sealing early protects the edges.
How the job changes by surface
Concrete and precast panel joints
Precast and concrete panel joints move daily. The sealant needs the right movement capability and a controlled depth.
Internal floor movement joints
Floor joints include saw-cut joints and construction joints. Trafficked floor joints often get a semi-rigid filler and a flexible sealant where the joint moves more.
From enquiry to sign-off
Where the site stays busy, the work is phased so only one area is out of use at a time. Each section is protected, cleaned back and sealed, then handed back before we move to the next. Rural sites near Kent Street may need directions, gate codes or a contact on site. Add it to your enquiry and we’ll build it into the plan.
- We start with photos, approximate lengths and any drawings, visiting where needed.
- Joint widths and expected movement are checked against what the sealant can take.
- Old sealant and debris are cut out of every joint.
- Edges are checked, and we tell you if any need repairing before sealing.
- The right sealant goes in at the right depth, bonded to the two sides only.
- Each area is handed back after its cure time, under our 12-month guarantee.
Before we start on site
- Point out any areas we must not close
- Arrange parking or a loading space
- Send asbestos survey details if the building is pre-2000
Ask for a quote
To get a fixed quote, phone 01277 525 020 or use the quote form with the site address and an outline of the work. Our quote form is another easy route.
Advice
Expansion joint sealing around Kent Street: how the place shapes the job
The South East is one of the drier parts of the UK. Even so, yard and car park joints are only sealed when they’re dry and clean, and where de-icing salt is spread in winter, open joints let it in. Kent Street is about 26 miles from central London. Distribution warehouses and industrial estates are common around the motorway corridors that serve the capital.
In a school such as Kings Hill School, movement joints in brick, block and hall floors tend to be forgotten until they leak. A healthcare site such as Maidstone Hospital (4.3 miles east of Kent Street) depends on car parks, ramps and service yards whose joints take traffic all day.
Kent Street is about 6 miles west of Maidstone, in Kent. Anywhere in ME18, it works the same way: details in, fixed quote out, then sealing and a 12-month guarantee. We work across 931 places in Kent, large and small. We also cover London, around 26 miles from Kent Street.
If you need expansion joint sealing in ME18, the process matches everywhere else we work: send details, get a quote, we seal, guaranteed. Among the streets we cover are Kent Street and Malling Road, and sites on any of them can send details for a fixed quote. If your building is just outside Kent Street, we cover Herne Pound (1 mile south-west), Mereworth (1 mile south), New Pound (1 mile west), Pizien Well (1 mile south-east) and Swanton (1 mile south-west). Further afield, our area takes in Maidstone (6 miles east), Dartford (14 miles north-west), Sevenoaks (9 miles west), Royal Tunbridge Wells (10 miles south-west), Gravesend (11 miles north) and Tonbridge (7 miles south-west).
Near you in Kent Street
Recent enquiries here include premises near The Queens Head Public House and Manor Park Country Park, among other places. Kent Street’s nearest station is Wateringbury station, about 2.1 miles south-east of the centre. Other landmarks nearby include Beechin Wood Archery Museum (2.5 miles north-west) and Maidstone Hospital (4.3 miles east).
What we are called out for in Kent Street
On trafficked joints, wheels and salts do the damage. Tyres and wheels press on the edges and the sealant, while grit and salts work into any gap. The product has to be suited to the traffic.
What tends to prompt an enquiry:
- Sealant pulling off the joint face
- Previous reseals laid over old sealant
- Expansion joints filled with dirt and stones
- Chipped joint edges on forklift routes
Business parks such as Kings Hill Business Park, 0.8 miles north-east of Kent Street, have car parks, paved areas and long brick and panel elevations, all with movement joints.
Questions to ask before you book
- Proof of insurance
- Is the sealant right for the movement and the substrate?
- Is depth set with backing rod, or bond-breaker tape in shallow joints?
- Their pre-qualification and accreditations