Gordon expansion joint sealing
Our CSCS-carded applicators take on expansion and movement joint sealing in walls, decks and floors in Gordon. Send details for a fixed quote.
- Expansion joints split through the centre of the bead
- Previous reseals laid over old sealant
- Water getting into the wall through a failed joint
Need expansion joint sealing in Gordon?
Photos, a specification or a quick description of the joints is enough to start a fixed quote.
Expansion joint sealing in Gordon
Our movement joint work takes in walls, panels, decks and floors: vertical joints in brick and block facades, joints between precast or cladding panels, concrete slab and deck joints, ramps, podiums and internal floors. Every one calls for a sealant picked for its movement, exposure and traffic. The enquiries we see most involve expansion joints split through the centre of the bead and water dripping through deck or ramp joints, on podiums and floor movement joints, car park decks and ramps and blockwork control joints. Looking for mastic applicators who cover Gordon? Mastic Doctor has worked for contractors, FMs and building owners since 2005, with CSCS-carded applicators.
Travel to smaller places like Gordon is planned so the work is done in one trip where possible. Photos, approximate widths and what uses the floor help us bring the right materials.
What our 12-month guarantee covers is the way we did the job: the preparation, the sealing and the tooling. It doesn’t extend to damage, other trades’ later work or movement the joint was never designed to take.
- Where
- Gordon (TD3)
- Wider area
- Scottish Borders
- Cover
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Call
- 01277 525 020
- Last updated
- 3 November 2026
Joints that move: notes for Gordon
Gordon is on Scotland’s drier eastern side. Freezing weather and salt still attack open external joints. Autumn is a sensible time to seal them.
In and around Gordon, the right filler or sealant for each joint depends on the traffic and the movement it takes.
Gordon is about 10 miles north-east of Galashiels, in the Scottish Borders. Anywhere in TD3, it works the same way: details in, fixed quote out, then sealing and a 12-month guarantee. Gordon is one of 91 places we cover in the Scottish Borders for movement joints. For work in that direction, see our Edinburgh page.
We cover the TD3 postcode districts. Streets here include Main Street, Station Road and Murrayfield. Nearby places we also cover include Smailholm (4 miles south), Westruther (4 miles north), Greenlaw (4 miles north-east), Stichill (5 miles south-east) and Earlston (5 miles south-west) for movement joints. Further afield, our area takes in Galashiels (10 miles south-west), Kelso (7 miles south-east), Selkirk (14 miles south-west), Jedburgh (14 miles south), Duns (11 miles north-east) and Melrose (8 miles south-west).
What’s near Gordon
Well-known places in the area include Mellerstain House (2.5 miles south). The countryside around Gordon includes Gordon Moss and Brotherstone Hill.
What happens if it’s left?
A torn seal left alone typically gets worse. Grit and water fill the gap and the material either side breaks up. Acting at the first split keeps the cost down. In Scotland, wind-driven rain finds a failed joint quickly, so it’s worth renewing joints around Gordon before they leak.
Cost follows what’s involved: stripping out, preparation, sealing, access and phasing. Call for a fixed quote and we’ll explain how it’s made up.
Why appoint us
- A range of standard colours, depending on the product
- Products installed to the manufacturer’s instructions
- One contact handling all your sites
- RAL and finish matching where the product range allows
Read how commercial sealant jobs are priced and our accreditations.
Towns and villages near Gordon
Also in Gordon
When to bring in a specialist
There’s also the paperwork. Many sites expect CSCS cards, RAMS and proof of insurance, and our CSCS-carded applicators are used to working under those rules.
Site maintenance staff can often handle a short internal joint. Where it goes wrong is preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
Diagnose, treat, sign off
At the end of each section, we remove the tape, clean down and inspect every joint with your site contact. Where the sealant needs time to cure before use, we tell you and sign the area. Travel to smaller Scottish places like Gordon is planned so the job is finished in one visit where possible, so photographs, sizes and a full list matter. Outside work also needs a suitable weather window.
- Photos, joint lengths and drawings come to us, or we visit.
- Joint widths and expected movement are checked against what the sealant can take and tell you if the design looks wrong for the movement.
- Old sealant and debris are cut out of every joint.
- Edges are checked, and we tell you if any need repairing before sealing.
- A sealant suited to the movement and traffic is laid to depth and tooled.
- Areas reopen once cured, and the work carries our 12-month guarantee.
Before we start on site
- Make sure the joints can be reached
- Point out any areas we must not close
- Point out parking and an unloading spot
Quotes
The quickest route to a quote is a few photos and the site postcode. Upload them with the quote form, or call 01277 525 020 or send details through our quote form if you’d rather talk the job through.
Advice
Signs you need expansion joint sealing in Gordon
Weathering wears down sealant on exposed elevations and decks. UV hardens the surface, and the sealant loses its ability to stretch, so it can’t follow the movement any more.
Look out for the following:
- Chipped joint edges on forklift routes
- Car park joints leaking onto vehicles below
- Torn sealant in brick or block movement joints
- Expansion joints filled with dirt and stones
Around Gordon, open joints collect water and debris, and the arrises are the next to go; we will tell you if the edges need repairing first.
Before you book anyone
- Which product they’ll use, and why it suits the joint
- Whether old or failed sealant will be cut out, not overlaid
- How they handle RAMS and site documents
- Their public liability cover
Building owners, agents and FMs in Gordon
For main contractors, we work as the sealant subcontractor, on new build and refurbishment alike. Programme, specification and site rules come first.
As a CHAS accredited contractor and Constructionline member, we’re straightforward to vet for your supplier list. We’re fully insured, and our insurance certificate can go with the quote.
Honest limits
Part of a good diagnosis is knowing where sealant stops. We’ll tell you if the real problem is any of the following:
- Leaks coming from the membrane rather than the joint seal
- Changing the joint layout or spacing of a structure
- Broken or spalled joint edges, which need repairing before any sealant goes in
Not sure which it is? You can call 01277 525 020 or send details through our quote form and we’ll tell you honestly before you book.
Where we work in Gordon
- Brickwork movement joints
- Precast concrete panel joints
- Podiums and floor movement joints
- Cladding panel joints
- Blockwork control joints
- Car park decks and ramps
Common questions from Gordon clients
Is Gordon too far out for you?
No. Places such as Gordon are covered as much as the big towns. We work across every Scottish council area. Where we can, we group nearby jobs to make the most of each trip.
Do we have to stop operations in Gordon while the joints are sealed?
In most cases the site keeps working. Joints are done in phases, a bay, aisle or deck at a time. Tell us which hours and entrances we can use and we will plan from there.
Can you fit around our working hours?
Mention the site’s hours and access windows in your enquiry, and we’ll plan around them. Our office runs Monday to Friday, 8am until 5pm.
Can you seal car park deck joints?
Yes. Tell us how the car park is used and which areas must stay open and we’ll plan around them.
Are you CHAS accredited?
Yes. We are CHAS accredited and a Constructionline member, which helps with supplier vetting.
Can you follow the specification on our project?
Yes. The specification and the manufacturer’s installation guidance are what we work to, and we raise anything unclear before work begins.
What sealant do you use in movement joints?
We choose a sealant with a movement capability that suits the joint. Hybrid or MS polymer products suit some mixed-material joints.