Expansion and movement joint sealing in Airlie, Angus
Planning work on a movement joint in Airlie? We look at it, seal it with the right product and hand it over with a 12-month guarantee.
- Sealant peeling off one face of the joint
- Hardened, cracked sealant on exposed facades
- Water dripping through deck or ramp joints
Expansion joint sealing for businesses in Airlie
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
On site: what to expect
In a busy building, the work is phased so only one area is out of use at a time. Each section is protected, cleaned back and sealed, then handed back before we move to the next. Jobs near Airlie are often grouped with others in the same area, to make the most of each trip. Let us know if your dates have any give.
- Photos, joint lengths and drawings come to us, or we visit.
- We compare each joint’s width with the movement and the sealant’s capability, and flag anything that needs an engineer.
- Every joint is cleared of the failed seal and any grit packed into it.
- Edges are checked, and we tell you if any need repairing before sealing.
- The right sealant goes in at the right depth, bonded to the two sides only.
- Areas reopen once cured, and the work carries our 12-month guarantee.
Before we start on site
- Warn occupants and staff about the work
- Tell us which areas need to stay in use
- Flag any permit to work we will need
Ask for a quote
To get a fixed quote, ring 01277 525 020 or email a schedule or drawings, telling us the site location and the nature of the job. You can also send details through our quote form.
Related advice
About our expansion joint sealing in Airlie
Floor movement joints in warehouses, retail and public buildings carry wheeled traffic. Unsupported edges break up under wheels, so the right filler or sealant for the traffic and movement matters. If the arrises are already broken, we will say so before sealing, and phased work keeps areas in use. We work on blockwork control joints, precast concrete panel joints and brickwork movement joints, and the failures we’re asked to look at most are previous reseals laid over old sealant and car park joints leaking onto vehicles below. Sealant applicators who only do sealant are a different proposition from a general trade with a gun in the van: on jobs in Airlie, preparation and product choice get the time they need.
For outside joints near Airlie, the Scottish weather sets the timetable: dry faces and the right temperature are essential, so dates have some give. Inside slabs aren’t affected and can be scheduled around the occupier.
Whoever the client is, the cover is the same: a 12-month guarantee on our workmanship. Faults in the structure, damage and other trades’ work fall outside it, and we say so plainly.
- Where
- Airlie (DD8)
- Wider area
- Angus
- Cover
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Slabs, ramps and loading bays in Airlie
Airlie is on Scotland’s drier eastern side. Frost and winter road salt still work into open joints in car parks and yards. Sealing them in drier months limits winter damage.
Around Airlie, open joints collect water and debris, and the arrises are the next to go. For floors and slabs around Airlie, the product is chosen for the traffic and the movement at each joint.
Airlie is about 9 miles west of Forfar, in Angus. Anywhere in DD8, the process is the same: details in, fixed quote out, then sealing and a 12-month guarantee. Airlie is one of 65 places in Angus on our list for movement joints. Dundee is covered too, some 12 miles away.
Anyone looking for expansion joint sealing in DD8 gets the same process as the rest of our area: details, then a fixed price, then sealing and a 12-month guarantee. With the A926 nearby, Airlie is straightforward for us to reach. We also cover Westmuir (3 miles north-east), Meigle (4 miles south-west), Alyth (5 miles west), Glamis (5 miles south-east) and Kirriemuir (5 miles north-east). Further afield, our area takes in Forfar (9 miles east), Monifieth (15 miles south-east), Letham (13 miles east), Newtyle (6 miles south) and Liff (11 miles south).
What’s near Airlie
Nearby you will also find Baikie Castle (0.6 miles south). For a walk, there’s Loch of Kinnordy and Mile Hill.
FAQs: Airlie
Is Airlie off your patch?
No. Small places get the same service as large ones. Every Scottish council area is within our area. Send photographs and a list of what needs doing, and we’ll plan the job to need as few trips as possible.
Does a site in Airlie have to shut while its joints are sealed?
In most cases the site keeps working. Joints are done in phases, a bay, aisle or deck at a time. We agree the sequence and timings with you before we start.
What causes movement joint sealant to fail?
Most often the movement is too much for the product or the joint width. That’s why we check width, depth and movement class before quoting.
Can you handle several sites?
Yes. Several buildings can share a single quote, and you deal with one contact throughout.
What exactly is a movement joint?
The general name is movement joint, and expansion joint is one common type. In everyday use the two names are often swapped.
Does weather matter for sealant work?
Outside, yes. Sealant needs a dry joint and a temperature within the product’s range, so damp, frosty or very cold days can stop external work. Internal work is rarely affected.
Can a joint be sealed if the edges are broken?
Spalled edges need repairing before a new seal will last and we will flag every length affected. A bead on a broken edge soon lets go.
Also in Airlie
Why it’s worth doing now in Airlie
Leaving a failed movement joint rarely stays a small problem. Grit and water fill the gap and the material either side breaks up. Acting at the first split keeps the cost down. For buildings near Airlie, dealing with all the failing joints at once saves return trips. Send photos and we will quote for everything together.
Larger quantities, tricky access or phasing all shape the price. Site requirements like inductions and permits play a part as well, along with the time of year for external work.
Why appoint us
- Over 20 years of commercial sealing
- Fully insured
- A range of standard colours, depending on the product
- Products installed to the manufacturer’s instructions
See what affects the cost and our accreditations and insurance.
When something else is needed
We seal joints; we don’t mend everything behind them. On its own, sealant can’t deal with:
- Proprietary pre-formed expansion joint systems
- Cracking or settlement that calls for an engineer’s assessment
- A joint that has to be widened or re-detailed before it can work
If you are not sure, just ring 01277 525 020 or send details through our quote form and we’ll give you a straight answer before you book.
Surfaces we seal
- Precast concrete panel joints
- Car park decks and ramps
- Cladding panel joints
- Brickwork movement joints
- Blockwork control joints
- Podiums and floor movement joints
How the quote is worked out
These are the things that shape the price:
- Backing rod, priming and other preparation
- Whether the work must be split into stages
- The site’s rules and procedures
- How much existing material needs removing
The specified product makes a difference, and so does the preparation, such as cutting out, priming or new backing rod. Access, phasing and site rules also count.
What we need to price the job
However big the job, the same details help:
- Any specification or named product
- When you need the work done
- Approximate linear metres or a joint schedule
- The asbestos register, for older buildings
If there’s a specification, drawings or a tender package, send it with your enquiry, and we will price the work to it. Smaller jobs need nothing more than photographs and a few notes.
What the job involves on each surface
Cladding panel joints
Cladding panels move more than masonry as they heat and cool. A sealant with the right movement class is chosen.
Joints between different materials
Different materials meeting at a joint rarely move in step. We choose a sealant that grips both faces priming where the maker calls for it.
General trades versus a specialist
A short, simple internal joint is often within reach of a maintenance team. The usual problems come from preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
Certain joints really need a specialist: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. A poor seal in places like these tends to cost more to put right later.