Coloured and colour-matched sealant in Ferring, West Sussex
Coloured sealant in Ferring, backed by over 20 years in commercial sealing. Fully insured and CHAS accredited.
- Colour changes after a rebrand or refit
- Marked sealant in hotel bathrooms
- Smeared sealant on stone or joinery
Coloured sealant near Ferring
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Coloured sealant for commercial buildings in Ferring
A coloured bead has to perform like any other sealant. Each joint is cleaned, backed to depth and tooled firmly onto both faces. Careful masking keeps the edges crisp. We work on powder-coated and anodised frames, cladding panels and natural stone and brick, and what we are called in for most is smeared sealant on stone or joinery and marked sealant in hotel bathrooms. Whether you call it commercial sealant work, mastic application or joint sealing, the work in Ferring is the same: the right product in a properly prepared joint.
In a smaller place such as Ferring, commercial buildings are normally a mix of shops, a pub or café, a school, a surgery and perhaps a few business units. Each job is modest, yet a joint in a small café needs the same cutting out, cleaning and sealing as one in a city office.
Every job ends the same way: guaranteed. You get a 12-month guarantee on our workmanship, and we explain exactly what that covers when we quote.
- Place
- Ferring (BN12)
- Wider area
- West Sussex
- Cover
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
How a job runs
We begin with a short walk round with whoever looks after the building, agreeing which joints are in scope, where to start and what must stay open. Then we strip out anything that has failed, prepare every joint and seal it. Several jobs near Ferring can be grouped on one trip. Tell us your site hours and we will plan around them.
- First we agree which sealant type the joint needs.
- We compare the target colour with the colours available.
- You approve the colour, on site if it’s critical.
- We cut out the existing bead, clean and set the depth.
- Edges are masked and the coloured sealant applied and tooled.
- Masking comes off and the work is checked with you.
Before we start on site
- Explain the parking and delivery arrangements
- Clear stock, furniture or equipment away from the joints
- Confirm the product named in the specification
Ask for a quote
Need a figure for a tender or a budget? We will quote against your scope and drawings that you can work with. If you have questions first, phone 01277 525 020 or email a schedule or drawings.
Read more
Also near Ferring
Also in Ferring
Keeping the joints sound
A few simple habits keep the new joints working:
- Plan full-run reseals on visible elevations
- Approve a sample bead on high-profile areas
- Don’t let trades patch coloured joints with a random sealant
- Clean coloured joints with mild products
Expect some change in appearance over the years. That is normal for exposed sealant.
Use one product and colour reference across a building or brand. Consistency makes future work simpler.
Questions we are asked in Ferring
Is Ferring too far out for you?
Not at all. Ferring is within our area. We cover Greater London and the counties of the South East. Good photos up front let us bring everything on the first visit.
Does your area include sites such as Goring Business Park, near Ferring?
Yes. Estates, retail parks and business parks around Ferring, Goring Business Park among them, are all within reach. Photos and a short description are enough for a first look.
How long do sealant joints last?
There isn’t a single answer, since movement, weather, cleaning and use all affect it. Regular inspection is the best way to catch problems early.
Can you fit around our working hours?
Give us your site hours and any access windows in your enquiry, and we will plan around them. You can reach the office between 8am and 5pm, Monday to Friday.
Can you send site paperwork?
Requirements differ from site to site, so tell us what you need and we will confirm it when we quote.
Do you seal on top of existing sealant?
No. Failed sealant is removed and the faces cleaned back to sound, dry material first, because fresh silicone will not bond with aged silicone.
Do you need to see the site first?
That depends on the size and complexity of the job. Straightforward work can often be priced from photos and measurements, and bigger or more complex jobs normally get a visit.
What happens if it’s left?
Standard white or grey sealant is cheaper to stock, but it doesn’t always suit the finish. On visible work, the small extra effort of a colour from the product’s range pays off at handover. For buildings in places like Ferring, one well-planned visit beats several small ones, so we’d suggest renewing all the joints that are going, not just the worst.
The specified product makes a difference, and so does the preparation. Access, phasing and site requirements come into it too.
Why us?
- 12 months’ guarantee on every job
- Colours chosen to suit frames, cladding or finishes where possible
- Coloured sealants to suit the setting, where available
- Health and safety: CHAS accredited
Take a look at what affects the cost or our accreditations.
Frontages, fit-outs and joints in Ferring
With the shore within about 1 mile, Ferring counts as a coastal location. Buildings near the sea put their external joints through more driven rain, with salt air nearer the beach. A matched colour is only half the brief on an exposed frontage. Rainfall across the South East, Ferring included, is lower than in many parts of the UK. External joints still need dry faces and the right temperature, and damp or frosty mornings can hold work up.
A hotel such as The Seaview Hotel, 1.5 miles to the west of Ferring, shows how much sealant a hospitality building has on show, from bathroom joints to the bar. On a business park such as Goring Business Park, which lies north-east of Ferring, sealant work tends to follow fit-outs: receptions, tea points, washrooms and frame perimeters.
Ferring is about 2 miles south-west of Worthing, in West Sussex. We cover Ferring, with the same fixed quotes and 12-month guarantee as everywhere else. Ferring is one of 373 places in West Sussex on our list for colour-matched joints. There’s a separate page for Brighton, about 14 miles away.
Business premises anywhere in BN12 are within our area. Buildings on Pebble Lane, Ferringham Lane and Grange Park are within our area for colour-matched joints. We also cover Kingston Gorse (1 mile south-west), Hangleton (1 mile north-west), West Kingston (1 mile west), Goring-by-Sea (1 mile east) and Angmering-on-Sea (1 mile west). Nearby towns on our patch include Bognor Regis (10 miles west), Chichester (15 miles west), Littlehampton (4 miles west), Shoreham-by-Sea (8 miles east), Lancing (6 miles east) and Rustington (3 miles west).
What’s near Ferring
Recent enquiries here include premises near Durrington Minature Railway and Chatsmore Catholic High School. Ferring’s nearest station is Goring-By-Sea station, about 0.9 miles north-east. Well-known places in the area include Rustington Museum (2.4 miles west) and Old Castle (2.6 miles north-east). Not far away are Highdown Hill.
Cost factors for colour-matched joints
To price the job, we consider:
- The site’s rules and procedures
- The product specified
- How much existing material needs removing
- The size and state of each joint
Whether it’s a single area or a whole estate, the same things set the price: scope, access, product and programme. Call for a quote and we will put a fixed figure on it.
Sending details for a quote
There’s no need for a formal survey. A few details are enough to get going:
- Whether an asbestos survey exists
- Where the site is, with the postcode
- Any dates the work must fit around
- Drawings or a marked-up plan, if available
The quickest route to a quote is a few photographs and the site postcode. Upload them with the quote form, or give us a call on 01277 525 020 or send details through our quote form to discuss it first.
Site staff or a sealant specialist?
Certain joints really need a specialist: fire-rated seals that must follow a tested detail, trafficked floor joints and external movement joints among them. A poor seal in places like these tends to cost more to put right later.
Site maintenance staff can often handle a short internal joint. The usual problems come from preparation: new sealant over old, damp or dusty faces, or the wrong product for the movement.
When to call us in Ferring
Older sealant changes colour over time. Sunlight, dirt and pollution can darken, yellow or chalk the surface, so joints that once matched no longer do. Resealing is the chance to reset the colour.
Look out for the following:
- Smeared sealant on stone or joinery
- A bead that fights the cladding or frame colour
- Coloured joints that have cracked with movement
- Shop fits that need consistent sealant colours across sites
Offices and shops close to stations such as Goring-By-Sea station (0.9 miles north-east of Ferring) tend to be busy all day, so sealant work is planned around opening hours.
Questions to ask before you book
- How they handle RAMS and site documents
- Their public liability cover
- Do they follow the manufacturer’s priming guidance?
- Which product they’ll use, and why it suits the joint