Fire Stopping in Point Clear
Work needed on a service penetration in Point Clear? We assess it, carry out the work and guarantee our workmanship for 12 months.
- Seals that don’t match their tested detail
- Damaged fire seals in risers and voids
- Service penetrations left open after M&E works
Fire stopping for businesses in Point Clear
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Fire stopping for commercial buildings in Point Clear
Facilities managers in Point Clear often find open service penetrations when ceilings come down for other work. Where the walls and floors already have a fire-stopping specification, we can work to it, matching the product and detail it names. With no specification in place, the first step sits with your designer or fire engineer, not with us. Site teams most often ask us about improvised or mixed-product fire seals and non-fire-rated filler around services, on joints between fire-resisting walls and floors, cable penetrations and service gaps in risers. For commercial sealant work in Point Clear, you deal with one contact from quote to sign-off, for single jobs and planned programmes alike.
For a smaller site near Point Clear, we plan to do all the penetrations in one go, so send the specification and photographs first. We install to the specification and the manufacturer’s guidance, leaving design and sign-off with the designer and building control.
What our 12-month guarantee covers is the way we did the job: the preparation, the sealing and the tooling. It doesn’t extend to damage, other trades’ later work or movement the joint was never designed to take.
- Where
- Point Clear (CO16)
- Wider area
- Essex
- Guarantee
- A 12-month guarantee
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Last updated
- 3 November 2026
When it isn’t the sealant
Not every problem is a sealant problem, and we’d rather tell you before you spend money. These need a different solution:
- Fire doors, dampers or other fire safety equipment
- Gaps in walls that were never built as compartment walls
- Writing the fire-stopping specification
If you’re not sure, just ring 01277 525 020 or send photos by email and we will give you a straight answer before you book.
Joints and surfaces we work on
- Linear gaps at wall heads
- Service gaps in risers
- Joints between fire-resisting walls and floors
- Pipe penetrations
- Small duct penetrations where the tested detail allows
- Cable penetrations
Doing it in-house
A short, simple internal joint is often within reach of a maintenance team. The usual problems come from preparation: sealing over old material, sealing onto damp or dusty surfaces, or a product that can’t take the movement.
Using site staff can make sense for a small touch-up, but anything bigger is another matter: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
When to call us in Point Clear
Some service penetrations were never sealed at all, often hidden above suspended ceilings or behind boxing. Inspections, refurbishments and ceiling access usually bring them to light.
Common reasons buildings call us in:
- Open linear gaps along the top of fire-resisting walls
- Unsealed penetrations discovered above suspended ceilings
- Damaged fire seals in risers and voids
- Fire-stopping items raised at inspection or handover
Halls and meeting rooms at places like Church of St James sometimes gain new services, and any compartment wall crossed needs the specified seal.
Comparing quotes
- How the existing material will be dealt with
- How joint depth will be controlled
- How they handle RAMS and site documents
- Who will actually carry out the work
Towns and villages near Point Clear
What else we do in Point Clear
How a job runs
Diagnose, treat, sign off: every visit follows that pattern. First comes an inspection and agreement on scope, then we prepare and seal each joint with the specified product, and the job ends with a walk round and sign-off. For a building around Point Clear, tell us how to find it and who will meet us. Send that with the details and we’ll confirm the plan with the quote.
- We start with your penetration schedule, drawings or specification.
- We plan the sequence of floors, risers and voids with you.
- Each opening is checked for wall or floor type, service, gap and depth.
- Foam, ordinary sealant and debris come out so the seal starts clean.
- The specified backing and sealant go in to depth and are finished neatly.
- Anything outside the detail is reported to you rather than sealed.
Preparing the site
- Clear stock, furniture or equipment away from the joints
- Tell us which areas need to stay in use
- Tell us what induction or permit system the site runs
Get a fixed quote
Need a figure for a tender or a budget? Send the scope and any drawings, and we will return a fixed quote you can plan around. If you have questions first, phone 01277 525 020 or email drawings and photos.
Related advice
Penetration seals near Point Clear
Point Clear lies roughly 53 miles out from central London. Tenant changes on commuter-belt business parks mean regular fit-outs, and new services through compartment walls; the gaps need the specified seal. Fire stopping of openings and penetrations in England falls under Approved Document B. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. Either way, we install the specified product to its tested detail.
In a hotel such as The Anchor Hotel, which lies north-west of Point Clear, new pipework or cabling through bedroom and corridor walls needs sealing with the specified product. Schools such as Colne Community School and College often have new data and services installed during holidays, and penetrations through fire-resisting walls should be checked afterwards.
Point Clear is about 5 miles west of Clacton-on-Sea, in Essex. Looking for fire stopping in Point Clear? We can help, as we do across Essex. Our Essex coverage takes in 644 places, from busy centres to rural villages. We also cover London, some 53 miles away.
We cover the CO16 postcode districts for service penetrations. Streets here include Oakmead Road, Seaview Terrace and Alpha Road. Close to Point Clear, our area also takes in Brightlingsea (1 mile north), Lee-over-Sands (2 miles south), St Osyth (2 miles east), East Mersea (2 miles west) and Seawick (3 miles south-east). Nearby towns on our patch include Colchester (9 miles north-west), Clacton-on-Sea (5 miles east), Harwich (14 miles north-east), Camulodunum (9 miles north-west), Heybridge (15 miles west) and Greenstead (8 miles north-west).
Near you in Point Clear
Locally, jobs take us to sites close to Ferry Boat Inn. The closest station to Point Clear is Great Bentley station, about 4.1 miles north of the centre. Not far away are Howlands Marsh.
Point Clear: questions and answers
Is Point Clear too small for you to travel to?
No. Small places get the same service as large ones. Our area covers London and the South East counties. We plan jobs in smaller places so return trips are kept to a minimum.
How does the removal of BS 476 from Approved Document B affect fire-rated sealing in Point Clear?
From 2 September 2029, Approved Document B drops its BS 476 references in favour of BS EN 13501-2 classification, with transitional arrangements. Our part doesn’t change: the specified product, to its tested detail.
Will your applicators have CSCS cards?
Yes. Our applicators hold CSCS cards, which many sites require.
Do you take on small jobs?
Single areas, one-off repairs and whole buildings are all quoted the same way: send details, get a fixed quote, we seal, guaranteed.
Is the work guaranteed?
Yes. Workmanship is guaranteed for 12 months on every job.
Will you come and look before quoting?
It depends on the job. Simple work can often be priced from photographs, and bigger or more complex jobs typically get a visit.
Can you handle several sites?
Yes. We take on portfolio and planned maintenance work, with each site phased to suit its occupants.
Aftercare for building managers
To get the most from the new sealant:
- Agree the fire-stopping specification before services go in
- Don’t let anyone top up a fire seal with the wrong product
- Leave fire sealant to cure fully before covering it
- Put resealing into every M&E and fit-out package
Store the specified product details somewhere the next contractor can find them. It makes later repairs much easier to match.
A simple record of seal locations and products helps. When a new service goes through, everyone knows which product and detail to match, and it helps at inspections.
Different surfaces, different methods
Plastic pipes
Waste and drainage pipes through floors are a frequent case. Whether sealant alone is acceptable depends entirely on the tested detail, and we won’t substitute it for a specified collar.
Linear joints
Joints at the top of partitions may need to move as the slab above deflects. The specified product and backing for that movement are what goes in.