Fire-rated sealing and fire stopping in Bramshott, Hampshire
Fire-rated and intumescent sealing of service penetrations and linear gaps across Bramshott, by CSCS-carded applicators. CHAS accredited and fully insured.
- Unsealed penetrations discovered above suspended ceilings
- Expanding foam used as fire stopping
- Old intumescent sealant that has split away
Fire stopping across Bramshott
Send drawings, photos or a joint schedule, or tell us about the site, and we’ll come back with a fixed quote.
Fire stopping for commercial buildings in Bramshott
We should be clear about what we do and don’t do. The designer, fire engineer or building control decides which fire stopping is required. We fit the specified fire-rated sealant following that specification and the maker’s installation guidance on buildings around Bramshott. We work on pipe penetrations, joints between fire-resisting walls and floors and cable penetrations, and the failures we’re asked to look at most are unsealed penetrations discovered above suspended ceilings and snag lists that include open service penetrations. Sealant contractors, mastic applicators, sealant specialists: whatever the job title on the order, in Bramshott it comes down to the same thing: the right product in a properly prepared joint.
Barn and farm-building conversions near places like Bramshott often combine new partitions with old walls. Where a pipe or cable passes through a fire-resisting wall, the seal must match the tested detail: product, substrate, gap and depth.
Work we carry out comes with a 12-month guarantee. Should something we installed fail, ring 01277 525 020 or send photos by email and we’ll come back to it.
- Place
- Bramshott (GU30)
- Wider area
- Hampshire
- Guarantee
- 12 months on our workmanship
- Quotes
- Quoted before any work starts
- Telephone
- 01277 525 020
- Page updated
- 3 November 2026
Diagnose, treat, sign off
In a busy building, the work is phased so only one area is out of use at a time. Each section is protected, cleaned back and sealed, then handed back before the next one starts. For a building around Bramshott, tell us how to find it and who will meet us. Send that with the details and we’ll confirm the plan with the quote.
- The specification and schedule come first, so we know which details apply.
- Access, permits and the order of areas are agreed with the site team.
- We compare every service penetration with its tested detail before sealing.
- Unsuitable material is removed and the opening cleaned so the seal starts clean.
- Backing and fire-rated sealant are installed to the detail and tooled.
- We tell you about openings that need a different product.
Before we start on site
- Make sure the joints can be reached
- Tell us which areas need to stay in use
- Arrange parking or a loading space
Getting a fixed quote
Specifications, drawings and tender packages are welcome with any enquiry, and we will price the work to it. For smaller jobs, photos and a description will do.
Related advice
Maintenance after handover
To get the most from the new sealant:
- Settle who seals which penetrations at the start of a project
- Make fire stopping part of every scope that crosses a fire-resisting wall
- Include service cupboards in routine inspections
- Record which product was used where
Allow the manufacturer’s stated cure time before boxing in or decorating. Not every fire-rated product can be painted.
Keep a register of where seals are and what they are made of. When a new service goes through, everyone knows which product and detail to match.
Leave it or put it right?
Fire stopping is a regular point raised at inspections and handover. Late discoveries can delay handover while openings are reopened and resealed which is why earlier is better. Converted and older buildings near places like Bramshott tend to move, and aged sealant cracks. A sealant with the right movement capability, correctly sized, lasts far better.
Whether it’s a single area or a whole estate, the same things set the price: scope, access, product and programme. Call for a quote and we will put a fixed figure on it.
Why us?
- Old sealant cut out, never sealed over
- Fully insured
- Constructionline member
- One contact handling all your sites
Cost factors for service penetrations
Quotes vary with the job. Expect it to depend on:
- Location, for remote and island sites
- Specialist products, such as fire-rated or hygienic sealants
- How much there is to seal
- Working within restricted access windows
Quantities, awkward access and phased working all shape the price. Site requirements like inductions and permits play a part as well.
Sending details for a quote
It doesn’t need to be a full survey. A few details are enough to get going:
- Rough lengths or quantities, or drawings if you have them
- Your programme or deadline
- Specification clauses that apply
- The type of building and who uses it
Let us know the site, the scope and your timescale, and a fixed quote will follow. The easiest way is to ring 01277 525 020 or email a schedule or drawings.
Fire stopping in Bramshott: the local picture
In England, Approved Document B covers fire stopping of openings and penetrations. The national BS 476 classes are due to drop out of it from 2 September 2029, leaving the European BS EN 13501-2 route, subject to transitional arrangements. Our part stays the same: the specified product, installed to its tested detail. Bramshott lies roughly 41 miles out from central London. Offices around the capital are refitted often, and the cabling that follows can breach fire-resisting walls; the gaps need the specified seal.
Hospital estates such as Holy Cross Hospital (2.7 miles east of Bramshott) are divided into fire compartments, and any service penetration through them should be sealed to the specified, tested detail. In a building such as Church of St Mary, any service penetration through a fire-resisting wall should be sealed to the specified detail. For a hotel such as Royal Anchor Hotel (1 mile south of Bramshott), penetration seals are worth checking after any refit or services upgrade.
Bramshott is about 8 miles south of Farnham, in Hampshire. Looking for fire stopping in Bramshott? We can help, as we do across Hampshire. Bramshott is one of 723 places in Hampshire on our list for service penetrations. Portsmouth is covered too, around 23 miles from Bramshott.
We take on service penetrations across the GU30 postcode area, for business premises of every kind. Buildings on Church Road, Limes Close and Woolmer Lane are within our area. Close to Bramshott, our area also takes in Hammer Bottom (2 miles east), Linchmere (2 miles south-east), Bramshott Chase (2 miles east), Hammer (2 miles east) and Woolmer Hill (2 miles east). Further afield, our area takes in Farnborough (14 miles north), Fleet (13 miles north), Aldershot (11 miles north), Alton (9 miles north-west), Petersfield (8 miles south-west) and Bordon (3 miles north-west).
Near you in Bramshott
Recent enquiries here include premises near Bohunt School and The Green Dragon Public House, among other places. For rail, the closest station is Liphook station, about 1.4 miles south of the centre. Other landmarks nearby include Chase Community Hospital (2.9 miles west). For a walk, there’s Lynchmere Commons and Wheeler's Down.
For managing agents and facilities managers
Facilities managers want contractors who arrive with the paperwork sorted. Tell us what site paperwork you need, such as RAMS, an insurance certificate or CSCS details, and we will confirm with the quote.
When you manage a building on behalf of an owner, clear figures and clear communication matter. We quote a fixed sum, confirm the scope and walk the finished work with you or your representative.
Towns and villages near Bramshott
Other services in Bramshott
Your questions answered
Is Bramshott off your patch?
No. Small places get the same service as large ones. We cover Greater London and the counties of the South East. Where we can, we group nearby jobs to make the most of each trip.
Is Passfield Industrial Estate, near Bramshott, within your area?
Yes. Our area takes in Bramshott and its surroundings, with estates and business parks such as Passfield Industrial Estate included. Send details of the unit and the work through our quote form for a quick quote.
What will the job cost?
We don’t publish prices, as every site differs. With photographs or drawings, we can give you a fixed quote.
Will you quote for a small job?
We quote for single jobs as well as large packages and programmes. Send details for a fixed quote.
What about RAMS and site documents?
Requirements differ from site to site, so list what you need, whether RAMS, insurance or CSCS details, and we’ll confirm with the quote.
What does an EI 60 rating mean?
BS EN 1366-3 covers penetration seals and BS EN 1366-4 covers linear joints. Classification follows BS EN 13501-2, where E is integrity, I is insulation and the number is minutes, as in EI 60. The rating applies to the product as tested.
Do you need to see the site first?
Photos, drawings or a schedule are often enough to quote. If the job needs a look first, we will arrange a visit.
What sealant work can’t fix
Some faults sit outside our scope, and we say so rather than covering them up:
- Deciding what a wall or floor needs, which belongs to the designer
- Fire risk assessments, a job for a competent assessor
- Approving the work on behalf of building control
If you are not sure, just call 01277 525 020 or email the details over and we will give you a straight answer.
Joints and surfaces we work on
- Service gaps in risers
- Cable penetrations
- Joints between fire-resisting walls and floors
- Small duct penetrations where the tested detail allows
- Linear gaps at wall heads
- Pipe penetrations