Facade Sealing contractors in Gogar
Sealant work in Gogar for main contractors, managing agents and facilities managers: facade joint and window perimeter sealing on commercial buildings, quoted at a fixed price.
- Old perimeter mastic that has dried out
- Draughts around frames and panels
- Staining on stone next to old sealant
Need facade sealing in Gogar?
Share the site address and what’s failing, and we’ll reply with a fixed quote or arrange a visit.
How we handle facade sealing in Gogar
Most facade joint failures trace back to the joint, not just the sealant. The width has to suit the expected movement and the sealant’s movement capability, and closed-cell rod sets the depth, keeping the bond to two faces with the ratio the sealant maker recommends, often around 2:1. Site teams most often ask us about failed seals around shopfront and entrance frames and unsightly perimeter sealant on a visible elevation, across perimeter joints where frames meet the structure, shopfront frames and cladding panel joints. One point of contact handles commercial sealant work in Gogar from the first photographs to the final walk-round, whether it’s one building or several.
Outside mastic in Scotland needs a dry, frost-clear joint, and in a place like Gogar that means watching the forecast. A little flexibility in the programme lets external joints go in on suitable days.
A 12-month guarantee applies to all our work in Edinburgh. If an installation problem shows up, give us a call on 01277 525 020 or email drawings and photos and we will arrange a return visit.
- Place
- Gogar (EH12)
- Region
- Edinburgh
- Guarantee
- A 12-month guarantee
- Quote
- Quoted before any work starts
- Call
- 01277 525 020
- Page updated
- 3 November 2026
Maintenance after handover
Sealant joints are maintenance items, and how long they last depends on how they’re treated. We suggest:
- Ask about asbestos in pre-2000 mastic
- Combine resealing with other works that need access
- Avoid patch repairs on failed facade joints
- Inspect facade joints on a regular cycle
If new signage, brackets or services are fixed through a sealed joint, the seal needs making good. Ask the installer to reseal it properly with a compatible product.
Check older buildings for asbestos before disturbing old mastic. Older sealants can contain asbestos.
Places near Gogar
What else we do in Gogar
What sets the cost
Sealant work doesn’t have a standard rate, since sites vary so much. What we take into account:
- Location, for remote and island sites
- The size and state of each joint
- Whether old sealant has to be cut out first
- How much there is to seal
Cost follows what’s involved: removing old material, preparing the joints, the product, the access and how the work is phased. Call for a quote and we will explain how it’s made up.
What to include in your enquiry
For an accurate fixed quote, we need a clear picture of the site. Useful things to include:
- The product your specification calls for
- The postcode of the building
- Access details, including height
- Photos of the joints, close up and from further back
The quickest route to a quote is a few photographs and the site postcode. Upload them with the quote form, or speak to us on 01277 525 020 or email a schedule or drawings if you’d rather talk the job through.
From enquiry to sign-off
At the end of each section, we remove the tape, clean down and inspect every joint. Where the sealant needs time to cure before use, we tell you and sign the area. For work around Gogar, we aim for one trip, which is why we ask for photos and a full list first. External joints need a dry spell as well.
- We start with photographs, drawings or a visit to see the joints and agree access.
- Product choice follows the joint’s movement and substrate.
- The existing bead comes out in full and both faces cleaned back.
- Primer goes on where the product data asks for it.
- Rod goes in to fix the depth, then the joint is sealed and tooled.
- We go over the completed work with you before leaving.
Preparing the site
- Point out parking and an unloading spot
- Tell us which areas need to stay in use
- Tell us what induction or permit system the site runs
Get a fixed quote
Tell us about the building, the joints and when you need the work done, and a fixed quote will follow. To get it moving, speak to us on 01277 525 020 or email the details over.
Related advice
Signs you need facade sealing in Gogar
The wrong product causes its share of trouble: acetoxy-cure silicone may mark stone or corrode certain metals, and an interior product won’t last outdoors. Neutral-cure, facade-grade products are what most external joints need.
Common reasons buildings call us in:
- Damp patches beside frames after rain
- Previous reseals run over old sealant
- Hard, chalky sealant that no longer flexes
- Facade joints cracked through the middle
Hotels like DoubleTree by Hilton Hotel Edinburgh Airport, 1.2 miles to the north-west of Gogar, rarely close for long, so refurbishment mastic is phased floor by floor.
Before you book anyone
- Their public liability cover
- Their pre-qualification and accreditations
- Will RAMS and insurance details be available?
- Is the sealant right for the movement and the substrate?
General trades versus a specialist
Certain joints really need a specialist: for instance fire-rated seals that must match a tested detail, trafficked floor joints and external movement joints. A poor seal in places like these tends to cost more to put right later.
For a quick touch-up, site staff may be fine, but larger jobs are different: a specialist brings efficiency, a consistent finish and a 12-month guarantee.
Surface by surface
Coping and flashing joints
Where the specification calls for sealant at copings or flashings, we can seal them. These joints take full exposure to weather.
Precast concrete panels
Precast arrises sometimes crumble or carry old residue. We clean back to sound material and flag edges that need repair first.
Mastic packages on Gogar sites
With the shore within about 3 miles, Gogar counts as a coastal location. On a coastal site, facade and perimeter joints face driven rain and, closer to the beach, salt, so we check the specified product suits the exposure before the first bead. The area within 2 miles of Gogar holds plenty of hotels. Hotel schemes tend to have fixed reopening dates, so the mastic is programmed tightly with the other trades.
Recladding or extending a unit at a site like West Craigs Industrial Estate (0.7 miles north-east of Gogar) brings panel joints and frame perimeters into the programme. Extensions at sites like Spire Murrayfield Hospital, 2.6 miles east of Gogar, normally sit beside working departments, and the mastic follows strict access rules.
Gogar is about 5 miles west of Edinburgh, in Edinburgh. Across the EH12 postcode area, it works the same way: details in, fixed quote out, then sealing and a 12-month guarantee. Our Edinburgh coverage takes in 174 places.
We take on facade joints across the EH12 postcode area. Close to Gogar, our area also takes in West Craigs (1 mile north-east), Maybury (1 mile north-east), Hermiston (1 mile south-east), East Craigs (1 mile north-east) and Ingliston (1 mile west). Nearby towns on our patch include Edinburgh (5 miles east), Leith (7 miles north-east), Bonnington (6 miles east), Greenside (6 miles east), Broughton (6 miles east) and Bellevue (6 miles east).
Landmarks near Gogar
For rail, the closest station is Edinburgh Gateway station, roughly 0.5 miles north-east. Nearby you’ll also find Craigcrook Castle (2.8 miles north-east) and Corstorphine Hospital (2.3 miles east). Open spaces near Gogar include Dundas Loch and Corstorphine Hill.
Questions about Gogar
Does your area include sites such as West Craigs Industrial Estate, near Gogar?
Yes, sites like West Craigs Industrial Estate are within our area, along with the rest of Gogar. To start, just call 01277 525 020 or send details through our quote form with the unit, the joints involved and your access times.
Can you work around term dates at a campus such as Heriot-Watt University?
Yes. We plan campus work around teaching, exams and residence turnarounds. Any paperwork you need, from RAMS to our insurance certificate and CSCS details, is confirmed with the quote.
Are your applicators CSCS-carded?
Yes. Our applicators hold CSCS cards.
Can you work while the building is occupied?
Usually, yes. We phase the work so most of the building stays in use.
Will you quote for a small job?
We quote for single jobs as well as large packages and programmes. Send details for a fixed quote.
How long do sealant joints last?
There’s no fixed lifespan: movement, exposure, cleaning, traffic and the product all play a part. Sealant joints are maintenance items, so inspect them regularly.
What type of sealant goes on window perimeters?
Most facade and window perimeter joints take a low-modulus neutral-cure silicone. Some joints call for hybrid, PU or polysulphide instead, depending on the substrate and the specification.